Festo DGC-40-600-G-PPV-A Rodless Cylinder

انهيار رمز النموذج

Material No.: 532449 = Base part number for standard DGC series rodless cylinder مع 40 مم تتحمل

`DGC-40-600-G-PPV-A`

1. DGC: Mechanical rodless linear actuator (steel band sealed rodless cylinder)
2. 40: Piston bore diameter Ø40 mm
3. 600: Effective stroke 600 مم
4. ز: Basic slide without integrated guide (piston slide only, no built-in guiding system. External linear guide is mandatory to bear loads and tilting moments)

GF: Integrated plain bearing guide; KF: Integrated recirculating ball bearing guide; ز: Basic version without guide

5. PPV: Adjustable pneumatic end cushioning on both ends, throttle-controlled damping at stroke limits
6. أ: Built-in sensor grooves on both profile sides for mounting SME/SMT proximity switches for position detection
7. المواصفات الفنية الأساسية

2.1 Pneumatic Performance

عملية: مزدوج المفعول

ضغط التشغيل: 1.5 ~ 8 حاجِز (0.15 ~ 0.8 MPa), rated working pressure 6 حاجِز

Theoretical push/pull force at 6 حاجِز: 754 ن

Air port: G1/4 on side of both end caps

Cushioning: Independently adjustable PPV air cushion at both ends

Maximum operating speed: ≤3 m/s

Repetitive positioning accuracy: ±0.1 mm (only valid with external guiding support)

2.2 حمولة & Moment Limits (Critical for G Version without Built-in Guide)

The G variant has no integrated guide. All radial forces and tilting moments must be absorbed by an external linear guide; the cylinder only transmits axial thrust:

Allowable static radial load Fy/Fz: 1380 ن

Allowable tilting moments: Mx: 28 ن · م; My: 54 ن · م; Mz: 33 ن · م

2.3 البيئية & Material Data

واسطة: جاف, filtered compressed air per ISO 8573-1 [7:-:-]

درجة الحرارة المحيطة: -10 ~ +60 درجة مئوية (النموذج القياسي, non-explosion-proof)

Seals: نبر / PU polyurethane

Profile & slide: Extruded aluminum alloy; sealing band: الفولاذ المقاوم للصدأ

Corrosion resistance class: CRC1, suitable for standard indoor automation environments

امتثال: بنفايات, شهادة CE

2.4 Weight Data (DGC-40-G)

Base weight at zero stroke: 2113 ز

Weight increase per 10 مم السكتة الدماغية: 49 ز

Total weight of this 600 mm stroke model: 5053 ز

Moving mass of slide: 732 ز

3. بناء & تعليمات التثبيت
4. Mounting options: Standard T-slots on bottom and side faces of the extruded profile, compatible with T-slot nuts, HPC foot brackets and flange accessories
5. Sensor mounting: Continuous sensor grooves on both sides of the profile, compatible with SME-8 / SMT-8 magnetic switches
6. Positioning reference: Mating locating pin holes on top and side surfaces of the slide for fixture alignment
7. Stroke limit configuration: No mechanical hard stops as standard; additional hydraulic shock absorbers (YSR series) or mechanical stoppers are required
8. Standard Delivery & الملحقات الاختيارية

Standard Included Components

Main cylinder unit DGC-40-600-G-PPV-A

Cushion adjustment screws on both ends

M8 mounting threaded holes on slide top face

Continuous sensor grooves (magnetic switches not included)

Common Optional Accessories

1. Position feedback: SME-8M-DS-24V-K-2,5-OE magnetic proximity switch
2. Mounting brackets: HPC-40 foot support, ZBH locating bushings
3. End-of-stroke damping: YSR-20-20 hydraulic shock absorber for two-end limiting
4. Stroke clamping unit: 1H-PN (holds position when air supply cuts off)
5. Pneumatic fittings: QS-1/4-8 push-in tube connector
6. طلب & Model Selection Guidelines

Suitable Applications

X-axis long-stroke feeding, transfer and door actuation for automated machinery

التعبئة والتغليف, woodworking, machine tool loading/unloading, reciprocating coating axes

Light-load mechanical systems equipped with separate external linear guides

Selection Pitfalls for G Variant

1.-G` has no integrated guide. It cannot bear lateral forces or tilting moments independently. An external linear rail is mandatory; خلاف ذلك, the sealing band will wear rapidly and the slide may jam.

2. For heavy loads, high precision or large tilting moments, upgrade to DGC-40-600-KF-PPV-A (integrated recirculating ball guide with zero clearance and greatly improved load capacity).
3. For strokes longer than 1000 mm running at high speed, add intermediate HPC support brackets to prevent profile deflection.
4. Install protective bellows accessory for dusty environments or applications with cutting fluid splashes.
5. Direct Replacement Models with Same Bore & سكتة دماغية
6. High-precision integrated guide alternative: DGC-40-600-KF-PPV-A (derived from same part number series 532449)
7. Cost-effective plain bearing guide alternative: DGC-40-600-GF-PPV-A
8. Compact short-stroke substitute: DGPL series guided rodless cylinder
9. Domestic equivalent alternatives: Airtac HTD40×600, SMC MY3B40-600
10. الأخطاء الشائعة & صيانة
11. Stick-slip motion / insufficient thrust: Cushion throttle fully closed, insufficient supply pressure, foreign debris trapped on sealing band
12. Air leakage: Worn end cap seals, damaged stainless steel band, aged cushion screw sealing rings
13. Slide jamming: Deformation caused by excessive lateral load, misalignment without external guiding
14. Maintenance cycle: Maintenance-free up to 5000 km under standard operating conditions; clean and lubricate the sealing band every 2000 km in dusty environments

Overall Installation Dimensions of Festo DGC-40-G-PPV-A (رقم الجزء. 532449)

1. Cross-section Profile Dimensions (Valid for All Strokes, وحدة: مم)

1.1 Profile Overall Width & ارتفاع

Total profile width B1 = 111.5

Total profile height H1 = 40

Height from bottom mounting reference surface to sealing band centerline: 55.75

1.2 T-slot Mounting Grooves (قاع & Side Faces Identical)

T-slot opening width T1=13.5, groove depth 2.1 مم, inner groove width 18 مم

Compatible T-slot nut: M8 standard type

1.3 Air Port Specification

G1/4 ports on both end cap sides; port center height from bottom surface: 16 مم

1.4 Dual-side A-type Sensor Grooves (Full-length)

Groove width 6 مم, عمق 8 مم, fits SME-8 / SMT-8 magnetic switches

2. Slide Mounting Dimensions (DGC-40-G Slide without Built-in Guide)
3. Total slide width: 111.5 مم (matches profile width)
4. Height of slide top mounting surface H3=93.8 mm
5. Top fixture mounting threads

4 main threaded holes M8, thread depth 9 مم

Central locating pin hole D1=Ø9 H7 (match with ZBH-9 locating bushing)

4. Overall slide length L1=278.4 mm
5. Clearance for cushion travel: Single-side pneumatic cushion travel length 29.5 مم (PPV cushion)
6. Overall Cylinder Length Calculation Formula

Fixed end cap extension length L2=258 mm for DGC-40-G

Total cylinder length L_total = Stroke + L2 = Stroke + 258 مم

For this 600 mm stroke model:

L_total = 600 + 258 = 858 مم

End Cap Related Dimensions

Distance from outer face of each end cap to extreme cushioned slide position: 29.5 mm per side

Protrusion length of side-mounted cushion adjustment screw: 8 مم

M6 tapped holes on both end caps for mounting HPC-40 foot brackets

4. Matching Dimensions for HPC-40 Foot Support Brackets (Standard Base)

Center distance between mounting holes on foot bracket: 90 مم

Fastening bolt: م8, locked via profile T-slots

Single bracket thickness: 19 مم; brackets used in pairs at both ends

5. Critical Clearance & Space Reservation Requirements
6. Full slide travel range: 0 ~ 600 مم
7. Single-side cushion occupied travel: 29.5 mm → usable mechanical contact stroke = 600 29.5×2 = 541 مم
8. Minimum clearance reserved at both ends for cushion adjustment operation: ≥15 mm
9. Maximum allowable protrusion height of fixture bolts on slide top: ≤6 mm to avoid scratching the sealing band
10. Quick Reference Dimension Table (وحدة: مم)

7. احتياطات التثبيت

1.-G` variant has no integrated guide. The cylinder body is only fixed by bottom T-slots; all lateral loads must be supported by an external linear guide.

2. Total length of 600 mm stroke unit is 858 مم. For horizontal mounting under heavy load, add one intermediate HPC-40 support bracket to prevent profile sagging.
3. M8 fixture screws on slide top must not be screwed deeper than 9 مم, to avoid damaging internal piston assembly.
4. Magnetic switches are inserted into full-length A-type grooves on both sides; switches can be installed at any position along the full 600 مم السكتة الدماغية.