ABB machinery drive ACS355-01E-02A4-2

ABB ACS355 series general machinery drive, 0.37 kW / 0.5 HP, single-phase 200–240 V input, IP20 protection, rated output current 2.4 UN. Suitable for speed control and energy-saving operation of small machinery.

1 Model Code Explanation

2 Key Technical Data

3 Key Features

3.1 Flexible Control

Predefined application macros: constant torque, fan/pump, PID control, etc..

Local/remote control switching via keypad, terminals or fieldbus

Built-in PID controller for closed-loop flow, pressure, etc..

3.2 Reliable Protection

Surintensité, surcharge, surtension, sous-tension, surchauffe, phase loss protection

Motor over-temperature protection (requires external PTC)

Short-circuit and earth-fault protection

3.3 Easy Operation

Compatible control panel with ACS350/510/550 series

Parameter copy function for fast commissioning

MTBF > 100,000 hours for continuous operation

4 Applications typiques

Small conveyors, machines d'emballage

Ventilateurs, pompes (small HVAC systems)

Mixers, centrifuges and small processing machines

Automatic doors, roller shutters

Medical equipment, instruments de laboratoire

Textile, printing and other light industrial machinery

5 Installation & Commissioning Guidelines

5.1 Exigences d'installation

Must be installed in an enclosed electrical cabinet

Ambient temperature: 0–40°C (derate 10% at 40–50°C)

Mount vertically, keep ≥ 100 mm clearance above and below for cooling

Avoid dust, oil, corrosive gases

Input protection: 10 A MCCB (C-curve) or fuse recommended

5.2 Basic Commissioning Steps

1. Pre-power check: Verify wiring (L1/N input, U/V/W output), couple aux bornes, proper earthing
2. Parameter initialization

Group 99: set motor rated voltage, actuel, pouvoir, speed

Select application macro (Standard, PID, etc.)

3. Control configuration

Local control: via control panel

Remote control: via DI terminals or optional Modbus RTU

4. Operation test

No-load test: run at 5–10 Hz, check rotation and stability

Load test: gradually apply load, verify current and temperature

Adjust acceleration/deceleration time (1–10 s recommended)

6 Cross-Brand Replacement Options (0.37 kW, 1-phase 220 V, IP20)

7 Selection & Conseils d'entretien

7.1 Recommended Options

Braking function: optional braking resistor (75 Ω / 50 W recommended)

Communication: add RS485 module

Enhanced EMC: additional input EMC filter

7.2 Entretien

Clean cooling channels every 6 mois

Check terminal torque annually

Avoid frequent starts/stops (≤ 20 times per day)

Storage temperature: -25°C à +60°C, dry environment

ABB ACS355-01E-02A4-2

Installation and Commissioning Manual

Overview: This manual provides complete instructions for safety, installation, wiring, parameter setting and commissioning of the ACS355-01E-02A4-2 drive (0.37 kW / 0.5 HP, single-phase 200–240 V) for general machinery speed control and energy saving.

1 Safety Instructions (Must Read)

1.1 Electrical Safety

Power-off procedure: Disconnect all power before installation, wiring or maintenance. Wait 5 minutes for internal capacitors to discharge.

Earthing: PE terminal must be reliably earthed (earth resistance ≤ 4 Ω)

Protection contre les surintensités: Install 10 A MCCB (C-curve) or fuse on input side

Insulation test: Only test motor cables; do NOT apply voltage to the drive itself

1.2 Mechanical Safety

Rotating parts (shaft, coupling, pulley) must be guarded

Mount vertically on solid surface to avoid vibration

Do not modify internal circuits or structures

1.3 Environmental Safety

Température de fonctionnement: 0–40°C (derate 10% at 40–50°C)

Humidité: 5–95% RH, non-condensing

IP20: must be installed in enclosed cabinet

2 Product Overview and Model Identification

2.1 Model Explanation (ACS355-01E-02A4-2)

2.2 Spécifications de base

3 Installation Procedure

3.1 Preparation

1. Unpack and inspect drive for damage
2. Choose well-ventilated, dust-free location inside cabinet
3. Outils: Tournevis cruciforme (PH2), pince à dénuder, crimping tool, multimètre, insulation tape

3.2 Montage

1. Mount vertically on flat metal plate
2. Keep ≥ 100 mm above/below, ≥ 50 mm left/right clearance
3. Fix with M4 screws, tightening torque: 1.2–1.5 N·m

4 Electrical Wiring

4.1 Terminal Description (ACS355-01E Series)

4.2 Étapes de câblage

1. Power wiring: L1/N to mains, PE to earth, U/V/W to motor
2. Control wiring (Standard macro example):

DI1: Forward (FWD), DI2: Reverse (REV), DI3: Reset

AI1: Speed reference (0–10 V)

3. Check torque, insulation, and phase sequence

5 Parameter Settings

5.1 Keypad Functions

▶/■: Commencer / Arrêt

▲/▼: Adjust value

ENTER: Confirm

ESC: Back

LOC/REM: Local / Remote

5.2 Quick Motor Settings (Group 99)

5.3 Common Application Parameters

6 Commissioning Flow

6.1 Pre-Power Check

Correct power and control wiring

Motor and drive area clear

Cabinet ventilation OK

Input voltage: 200–240 V single-phase

6.2 First Power-Up

Close MCCB, display shows REM or LOC

Check for fault codes

Verify Group 99 motor parameters

6.3 Motor Identification (Facultatif)

Set 9910 = 2 (ID Run)

Press ENTER; drive runs motor briefly

Completed when shown COMPLETE

6.4 No-Load Test

Switch to LOCAL

Run at 5 HZ, check rotation

Increase to rated frequency, check noise and vibration

6.5 Load Test

Switch to REMOTE

Control speed via AI1

Check output current ≤ 2.4 UN

Adjust acc/dec to avoid overcurrent

Test protection functions

7 Troubleshooting

7.1 Common Fault Codes

7.2 Typical Issues

8 Entretien

8.1 Entretien courant

Clean cooling channels every 6 mois

Check terminal torque annually

Log operating current and temperature

8.2 Long-Term Storage

Température: -25°C à +60°C

Sec, ventilated environment

Power on for 1 hour every 6 mois

9 Appendix: Options and Replacements

9.1 Recommended Options

Braking resistor: 100 Ω / 50 W

EMC filter

RS485 Modbus RTU module

Shielded cable for control wiring

9.2 Cross-Brand Alternatives (0.37 kW, 1-phase 220 V, IP20)

Manual Version: V1.0 (based on ABB official ACS355 manual, adapted for ACS355-01E-02A4-2)

Effective Date: February 2026

Copyright: ABB Group, Tous droits réservés