アレン・ブラッドリー 1747-AENTR アダプター

位置決め: SLC500 rack EtherNet/IP remote I/O adapter (NOT an SLC processor). It converts the existing 1746 SLC I/O rack into an EtherNet/IP slave, which is scanned and controlled by Logix コントローラー (CompactLogix, ControlLogix). It is the most commonly used gateway module for phased upgrades of legacy SLC systems.

✅ 基本仕様

シリーズ: A/B series; Latest firmware V2.003

ポート: 1 ×RJ45, 10/100 Mbps オートネゴシエーション, イーサネット/IP (CIP)

Mandatory mounting requirement: Must be installed in Slot 0 of the SLC chassis, replacing the original SLC processor position

バックプレーン: 1746 SLC backplane with SLC backplane master function

Connection resources: マックス. 96 クラス 1 (real-time I/O) connections, 最大. 8 クラス 3 (explicit message) connections

Network topology: スターをサポートします, linear, DLR (Device Level Ring)

IP構成: ディップスイッチ / BOOTP / DHCP; DIP switch set to `888` = factory reset

電源: Powered by the SLC chassis power supply, 消費電力約. 5 W

Software requirement: スタジオ 5000 / RSLogix5000 V20 or newer; matching EDS/AOP files required

Manuals: User manual 1747-UM076; Installation manual 1747-IN521

✅ 一般的な用途

1. Retrofit of legacy SLC systems: Retain all 1746 I/O modules and field wiring. Only replace the Slot 0 processor with 1747-AENTR and upgrade the main controller to CompactLogix/ControlLogix for phased migration without full shutdown.
2. Replacement of legacy remote I/O adapters: Substitute 1747-ASB (RIO), 1747-ACN15/ACNR15 (コントロールネット).
3. Operate as an EtherNet/IP slave for CIP explicit read/write access by HMI or SCADA hosts.

✅ Lifecycle & Migration Alternatives

状態: EOL, end-of-production date 2027-02-15. It is an engineering replacement part with no direct pin-compatible drop-in replacement.

Long-term migration options:

オプションA: Migrate the complete chassis to Compact 5000 I/O (5069 シリーズ)

オプション B: Keep existing field wiring and adopt 1746-to-5069 adapter base

Spare parts are only available as new-old-stock or used units. For second-hand units, verify firmware, イーサネットポート, backplane connector and indicator lamps.

✅ Indicator Definitions

わかりました: モジュールのステータス

LINK: Ethernet link status

I/O: SLC backplane I/O status

通信: CIP connection status

FORCE: Force signal active

✅ Key Common Faults

1. CIP 0x0010 fault: The controller holds an active connection lock on the module. Inhibit the module in Studio5000 before modifying IP settings, then remove inhibit after configuration.
2. Flashing COMM red & RPI timeout: Do not configure a short RPI for SLC analog modules (1746-NI4, OAP12 etc.). Recommended RPI: 50~100 ms, 最大 320 MS; short RPI causes frequent packet loss.
3. Invalid DIP IP setting (000 or value >254 and not 888): Module automatically uses BOOTP/DHCP for IP assignment.
4. Not all legacy 1746 modules are supported by AENTR; verify the support list in manual before configuration.

✅ Confusing Model Distinction

1794-セントラル: フレックス I/O (1794) EtherNet/IP adapter for Flex chassis, NOT compatible with SLC 1746 chassis

1747-L5xx: Native SLC processors with backplane master capability, functionally different from AENTR

1747-AENTR Common Faults, 症状, Root Causes & 救済策

前提条件: Module must be installed in SLC chassis Slot 0, occupying the processor slot; powered by SLC backplane; mainstream firmware V2.003; Studio5000 minimum V20; not all legacy 1746 modules are supported.

1. CIP 0x0010 (Hex 0010) 故障 (Most Frequent)

症状: Error when modifying IP or disabling BOOTP/DHCP via BOOTP/RSLinx; prompt “Set Attribute Single failed”; configuration cannot be written from controller side; IP reverts to DHCP after power cycle.

根本的な原因: クラス 1 I/O connection has been established by the controller. The module is connection-locked and rejects configuration writes from external tools.

Remedy Steps

1. Go online in Studio5000, right-click 1747-AENTR → Properties → Connection → ✅ Check Inhibit Module, apply, and terminate the I/O connection.
2. Modify IP and disable BOOTP/DHCP via BOOTP/RSLinx/web page to save static IP.
3. Remove inhibit after configuration is completed to restore communication.

代替: Put controller in Program mode or disconnect Ethernet cable; cable pull during production is not recommended.

2. COMM Red Flashing, I/O Timeout, RPI Timeout, Intermittent Slave I/O Faults

症状: OK 緑色に点灯, LINK steady green, COMM red flashing; slave modules (especially 1746-NI4, OAP12 analog modules) drop out periodically; RPI timeout logged.

根本的な原因

RPI configured too low for analog modules (デフォルト 20 MS; SLC backplane bandwidth is limited)

バックプレーンの接触不良, insufficient chassis power rating

Incompatible legacy 1746 module present

High backplane bus load or aged module hardware

救済策

1. Set analog module RPI to 50~100 ms, 最大 320 MS; adjust the AENTR adapter RPI accordingly.
2. 電源を切る, reseat all 1746 modules and clean gold fingers; verify SLC power supply capacity.
3. Cross-check against supported module list and remove incompatible modules.
4. Check backplane slot timeout counters via embedded web diagnostics to locate faulty slot.
5. OK Steady Red, Power-On Self-Test Failure, No Communication

症状: OK red solid after power-up, LINK off, module cannot be browsed in RSLinx.

根本的な原因

Hardware failure or corrupted firmware

Factory reset via DIP 888 failed

Poor backplane power supply, damaged Slot 0 backplane contacts

Module installed in wrong slot (not Slot 0)

救済策

1. Confirm installation in Slot 0 and test with a known-good SLC chassis power supply.
2. Set DIP switch to 888, power cycle for factory reset; reassign IP via BOOTP.
3. If OK remains red after reset: module hardware failure, ユニットを交換する.
4. LINK Off / 点滅, No Network Connectivity, RSLinx Cannot Find Module

症状: OK normal, LINK off or amber flashing, ping fails.

根本的な原因: イーサネットケーブルの損傷, defective switch port, speed mismatch, IP subnet mismatch, IPアドレスの競合.

救済策

1. Replace with qualified industrial Ethernet cable and change switch port; ensure switch port is 10/100M auto-negotiation (do not force gigabit).
2. Set DIP to 000, power up to obtain IP via BOOTP; ensure PC and module are on the same subnet.
3. Check network for IP conflict.
4. IP Reverts After Power Cycle, Static IP Will Not Save

症状: Static IP assigned and BOOTP disabled in BOOTP tool, but IP reverts to DHCP after power cycle.

根本的な原因: Only IP address changed, BOOTP/DHCP client toggle not disabled; 0x0010 connection lock prevents the disable command from being written to Flash memory.

救済策: Inhibit module first, then set BOOTP/DHCP to Manually Configure on module configuration page, confirm successful write, then remove inhibit.

6. AENTR Disconnect After Program Download (Known Bug for CompactLogix 5370 L3)

症状: より多い 5 I/O modules in chassis; AENTR loses communication after second program download, controller USB/Ethernet port also unresponsive.

根本的な原因: Rockwell known firmware defect.

Temporary workaround: Disconnect AENTR Ethernet cable before download; reconnect after controller enters Run mode. Long-term fix: Upgrade controller firmware or replace controller model.

7. Electronic Key Fault (Hex 0103)

症状: モジュール障害, type mismatch / keying failure alarm.

根本的な原因: AOP revision or firmware revision in project does not match physical hardware; or configured slot I/O model differs from actual installed module.

救済策

1. Read actual firmware revision from module and match firmware version in Studio5000 module definition.
2. Verify the part number of every 1746 module in chassis; avoid mixed use with compatible/disabled keying mode.
3. Reimport the matching AOP file.
4. FORCE Lamp Solid On

症状: FORCE indicator illuminated.

根本的な原因: One or more I/O tags are forced.

救済策: Clear all force tags in the force window of Studio5000.

9. Single Slave I/O Module Fault, Adapter Communication Normal

症状: AENTR communicates normally, only one slot module faults while other I/O runs fine.

根本的な原因: Failed 1746 モジュール, poor base contact, unsupported module model, local module power fault.

救済策: Swap the suspect module to another slot for cross-testing; verify module health; check support list.

Indicator Quick Reference

わかりました: Module status｜Green = Normal; Red = Fault / POST fail; Amber = Initializing

LINK: Ethernet link｜Solid = Link up; Blinking = Traffic present; Off = No link

通信: CIP I/O connection｜Green = I/O connection healthy; Red blink = Connection fault / timeout

I/O: SLC backplane I/O status｜Red = Backplane / slave module fault

FORCE: Force active

Standard On-Site Troubleshooting Sequence

1. Confirm mounting position: Slot 0 のみ
2. Read indicator status to isolate fault domain: network, adapter hardware or backplane I/O
3. Browse via RSLinx to confirm module accessibility and read firmware
4. If browsable: Inhibit module prior to IP/configuration edit; inspect RPI settings
5. If not browsable: Check cable, スイッチ, 電源, factory reset via DIP
6. Single backplane slot fault: Isolate by module swapping
7. Firmware corruption: Re-flash firmware with ControlFLASH Plus

Second-Hand Unit Inspection Checklist

1. Verify factory reset via DIP 888 works reliably
2. BOOTP assignment and embedded web page accessible
3. Stable steady green OK lamp after power-up, no fault
4. Chassis bench test: マウント 1746 DI module, build I/O tree in Studio5000, 走る 30 minutes without RPI timeout
5. Inspect Ethernet port and backplane gold fingers for corrosion or bad solder

Allen-Bradley SLC500 Full Model List (1747 Controller Family + 1746 Chassis & I/O Family, All EOL Discontinued)

注記: SLC500 consists of two main families: 1747 (Processors, Communication Adapters, Scanners) そして 1746 (Chassis, Power Supplies, デジタル I/O, アナログI/O, Specialty I/O). The whole platform is discontinued; spare parts are traded as new-old-stock or used hardware.

1. 1747 Processors (CPU)｜SLC5/01 ~ SLC5/05

2. 1747 Communication Adapters / Scanners (1747-AENTR Listed Here)

3. 1746 Chassis

4. 1746 Chassis Power Supplies

5. 1746 DI デジタル入力

6. 1746 デジタル出力DO

7. 1746 Combination I/O (ディ+ドゥ)

8. 1746 Analog I/O AI/AO

9. 1746 Specialty Modules (高速カウンター, 位置決め, BASIC etc.)

10. 付属品

1746-C7, 1746-RT25, 1747-BA (Lithium battery), 端子台, covers, expansion cables etc.

Supplementary Notes for Retrofit Projects

1. 1747-AENTR Compatibility Limit: Not all 1746 modules are supported. Early specialty modules (legacy HSCE, BAS) may not be recognized; analog module RPI must not be too short.
2. Easy Confusion: 1794-AENTR is Flex I/O adapter, not part of SLC500 (1746) family.
3. Migration Path: Preferred upgrade route for full SLC replacement: CompactLogix + 5069 Compact5000 I/O.