비&R 3DO479.6 출력 모듈

기본정보

시리즈: 비&R 시스템 2005 (더 이상 사용되지 않음)

이름: DO479 Digital Transistor 출력 모듈

전체 모델 번호: 3DO479.6

핵심 전기 사양

Mandatory Matching Terminal Blocks (Not included with module)

3TB170.9: 20-pin screw terminal block

3TB170.91: 20-pin spring-cage terminal block

Comparison of Similar Models within the Series

Replacement Solution for Phase-Out (System2005 → X20)

⚠️ Not plug-and-play compatible. Modifications required for backplane, terminal wiring and IO mapping in program.

옵션 1: Best functional match for new projects

X20DO4649

16~하다, 24VDC Sink, 0.5에이, grouped isolation, 진단 없음; electrically closest to 3DO479.6

옵션 2: With fault diagnostics (Recommended for equipment retrofits)

X20DO4529

16~하다, 0.5에이, with short-circuit diagnostics, convenient for on-site troubleshooting

Engineering Notes

1. Model Distinction: 3DO479.6 ≠ 3DO487.6. The latter offers higher current capacity and channel diagnostics; avoid mixed procurement.
2. Load Limitation: Freewheeling diodes are recommended for inductive loads (솔레노이드 밸브, 실린더) 트랜지스터 고장을 방지하기 위해.
3. Spare Part Status: Original manufacturer production discontinued. Available stock mainly includes used/refurbished units and limited new surplus; lead time and price fluctuate significantly.
4. Wiring Guidance: Sink output configuration. Connect 24V+ to load, then load to DO terminal; internal module circuit connects to 0V.

일반적인 애플리케이션 시나리오

포장 기계, 섬유 장비, 소규모 생산 라인, driving 24V solenoid valves, indicator lights and miniature relays.

Complete Troubleshooting Guide for B&R 3DO479.6

Important Premise: The 3DO479.6 has no built-in channel diagnostic feedback! The PLC program cannot detect short-circuit or hardware damage on channels. LEDs and multimeter measurements are required to distinguish module failures from external wiring/load faults.

1. Normal Operating Status Reference
2. Backplane power supply healthy: RUN green LED steady ON
3. Channel LED status: PLC output ON → corresponding LED ON; PLC output OFF → LED OFF
4. 출력 유형: NPN Sink

표준배선: 24V+ → Load → DO Terminal; internal module path connects to 0V when energized.

2. Step-by-Step Troubleshooting (From Simple to Complex)

단계 1: Inspect Power Supply and Backplane (Eliminate base/backplane faults first)

1. Verify stable 5V backplane power supply for System2005 rack;
2. Remove and re-seat the module, check backplane pins for oxidation or bending;
3. Cross test by swapping module positions: install the tested 3DO479.6 into a known good rack slot; install a confirmed good unit into the current slot.

If fault disappears after relocation → Backplane / base fault

If fault persists after relocation → Fault resides in module hardware or program configuration

Common RUN LED faults

RUN LED completely OFF: Loss of backplane power, internal module fuse blown or hardware failure

RUN LED flashing: Bus communication error (고문, backplane, incorrect CPU address configuration)

단계 2: Preliminary LED Check (Quick screening)

Force corresponding channel ON via PLC software:

1. ✅ Channel LED illuminates → Bus communication intact, module receives command correctly
2. ❌ LED fails to light after forcing ON

First verify IO address and hardware configuration match;

If address is correct and LED still off → Internal module logic circuit failure

중요한: LED only confirms command reception. LED ON does NOT guarantee valid output at terminals!

단계 3: Multimeter Measurement (Separate module faults from external load faults)

Measurement condition: External 24VDC load power connected

Meter setting: DC 전압

Normal Operating Condition (Channel ON)

Voltage between DO terminal and 24V 0V ≈ 0～2V (transistor conducting)

Channel OFF: Voltage between DO terminal and 0V ≈ 24VDC

Fault Phenomenon Judgement Table

⚠️ Critical test method: Disconnect all external wiring!

Remove all field cables from terminal block, conduct forced output test under no-load condition:

Abnormal performance under no-load → Module hardware failure

Normal no-load test, failure occurs only with load connected → External short circuit, leakage load or faulty solenoid coil

3. Unique Pitfalls for 3DO479.6 (Frequent Misjudgements)
4. No software diagnostics

Unlike the 3DO487.6, this module provides no short-circuit or wire-break feedback. PLC system alarms cannot be used to judge channel integrity.

2. Grouped power supply design with two independent circuits

Terminals are divided into two groups with separate external 24V load power supply.

Loss of power for one group disables all channels within that group while the other group remains functional. This is often mistaken for module damage.

3. High risk of channel burnout without freewheeling diodes for inductive loads

Solenoid valves and relay coils without parallel freewheeling diodes generate reverse electromotive force, breaking down output transistors, resulting in permanent ON or failed output channels.

4. Typical Signs of Permanent Hardware Damage
5. Single channel fails to output (LED ON with no terminal conduction)
6. Uncontrolled permanent channel conduction (transistor breakdown)
7. Complete failure of all channels within one group (faulty grouped driver circuit)
8. RUN LED does not light after power-up; no indicator response (blown internal fuse or main circuit failure)
9. Intermittent operation after minor short-circuit events
10. Quick Troubleshooting Summary
11. Swap slot position to rule out backplane faults;
12. Disconnect field wiring and perform no-load testing to isolate external faults;
13. Force channel status and compare LED status with multimeter voltage readings;
14. Abnormal no-load performance = module fault; normal no-load performance with loaded failure = peripheral circuit fault.
15. 수리하다 & Spare Part Recommendations

The module belongs to the discontinued System2005 platform. On-board component repair is not recommended due to poor long-term reliability after surface-mount component replacement.

Spare part solutions:

Temporary replacement: Used 3DO479.6 modules

Long-term retrofit: Migrate to X20DO4649; requires terminal wiring modification and IO address adjustment in PLC program.

Complete Procedure for Verifying 3DO479.6 Integrity

Core Premises:

✅ 3DO479.6 no channel diagnostic feedback, PLC alarms cannot assess channel status;

✅ Output type: NPN Sink;

✅ Two independent groups for external load power supply;

✅ LED only indicates command reception, LED ON ≠ valid terminal output.

준비

도구: 24V DC 전원 공급 장치, 디지털 멀티미터, 비&R programming software, terminal screwdriver

Core principle: Test under no-load condition first, then test with load. Distinguish module hardware faults and external wiring faults.

단계 1: Check Rack and Communication (Confirm overall module operation)

1. Mount module on System2005 backplane, power on and observe RUN LED

계속 켜져 있음: Backplane 5V power and bus communication normal

흘러넘치다: Poor backplane contact, backplane power failure or internal module burnout

RUN flashing: Incorrect bus address, faulty backplane or module hardware defect

2. Cross-slot testing (most effective method)

Install unit under test into a confirmed good rack slot; install a known good 3DO479.6 into the current slot.

Fault persists after relocation → Suspect module hardware

Fault disappears after relocation → Original rack/base/backplane fault

If RUN LED fails to light, module hardware damage is highly probable.

단계 2: No-Load Channel Test (비판적인! Remove all external wiring)

Disconnect all field cables from terminal block. Only keep backplane connection; disconnect external load power supply.

Force channel ON/OFF via programming software and measure voltage between DO terminal and 0V using multimeter:

Acceptable Benchmark

Channel forced ON: DO ↔ 0V ≈ 0～2V (transistor conducting)

Channel forced OFF: DO ↔ 0V ≈ 24V (transistor cut off)

Test Result Judgement

1. Channel forced ON, LED lit, voltage remains constant at 24V

👉 Internal channel transistor open circuit, module channel damaged

2. Channel permanently shorted to 0V even when OFF

👉 Output transistor breakdown, module damaged

3. All channels within one group fail while the other group works normally

👉 Faulty grouped power supply / driver circuit on module

4. All channels pass no-load testing → Module hardware intact; fault lies in external wiring, load or external 24V power supply

단계 3: Loaded Verification (Only performed after passing no-load test)

Reconnect wiring and energize external 24V load supply, repeat forced output test.

Normal no-load behaviour, failure occurs under load:

① External short-circuit; ② Load current exceeds 0.5A rating; ③ Missing freewheeling diode for inductive loads

✅ Module itself is undamaged!

Common Misjudgement Scenarios

1. All channels in one group stop output, other group works normally

👉 First check external 24V power supply for this group. Loss of external power is not equivalent to module failure.

2. LED lights up but solenoid valve does not actuate

LED only confirms command reception; terminal voltage measurement is mandatory.

3. Intermittent solenoid valve operation

Mostly caused by missing freewheeling diodes; reverse voltage gradually destroys output channels (detectable via no-load testing).

Checklist of Typical Module Failure Symptoms

Any of the following strongly indicates module damage:

1. No RUN LED illumination after power-up, no indicator activity;
2. Under no-load condition, LED turns ON on forced command but terminal cannot conduct;
3. Permanent channel conduction to 0V under no-load status;
4. Multiple channels malfunction under no-load test;
5. Obvious overheating, odour or bulging components when powered on.

On-Site Quick Inspection Formula

Remove field wires → No-load measurement;

Swap rack slots → Eliminate backplane faults;

LED status is not equivalent to output; rely on multimeter readings;

Abnormal no-load test = faulty module; normal no-load, loaded failure = peripheral fault.

비&R System2005｜Full Series Matching Models for 3DO479.6

Platform: 체계 2005 (더 이상 사용되지 않음); 3DO479.6 16-channel NPN transistor output module

1. Mandatory Terminal Accessories (Ordered Separately)

2. Digital Output Modules Interchangeable within the Same Rack

3. Commonly Used Matching Digital Input Modules

4. Mixed IO Modules (에서 + ~하다)

3DM476.6: 16에서 + 8~하다

3DM486.6: 16에서 + 16~하다

5. System Infrastructure (Backplane, 전원공급장치, CPU, 통신 모듈)

전원 공급 장치 모듈 (Leftmost slot on rack)

3PS465.9: 50여, standard mainstream unit (추천)

3PS477.9: High-power alternative

CPU Controllers

3CP340.60-1 / 3CP360.60-1 / 3CP380.60-1 / 3CP382.60-1

Communication Interface Modules (3IF Series, compatible on same rack)

3IF661.9, 3IF671.9, 3IF672.9, 3IF761.9, 3IF772.9, 3IF789.9 (Profinet/Profibus/CANopen/Ethernet)

Backplane Carriers (3BP Series, select based on slot count)

3BP152.4, 3BP155.4, 3BP180.4 (5-슬롯 / 8-슬롯 / 12-슬롯)

6. Analogue Modules (선택적 확장)

3AI375.6, 3AI775.6, 3AM050.6, 3AM055.6, 3UM161.6 (Combined AI+DI)

Important Compatibility Reminders

1. All above models can be mixed and installed on the same System2005 backplane with shared bus communication;
2. Terminal blocks are NOT interchangeable!

DO479/487/480 series require 3TB170.9 / .91 (20-핀)

32DI modules use TB718 terminals; do not mix.

3. Retrofit reminder: Migration to X20 platform is not plug-and-play. Modifications needed for backplane, wiring and PLC IO mapping.
4. Procurement note: 3DO479.6 ≠ 3DO487.6. Direct replacement is prohibited; availability of channel diagnostics is the core difference.

비&R System2005｜Project Procurement List for 3DO479.6 (Forwardable to Suppliers)

Platform: 체계 2005 (Fully Obsolete, only surplus new stock or tested used/refurbished units available)

Core Module: 3DO479.6 16-channel NPN transistor output module, no channel diagnostics

1. Core IO Modules

2. Matching Terminal Blocks (Supplied Separately, NOT included with modules!)

✅ Procurement Tip: 1 unit of 3DO479.6 requires 1 unit of 3TB170.9 or 3TB170.91

3. Rack Infrastructure (For complete PLC assembly)

전원 공급 장치 모듈 (Leftmost rack slot)

3PS465.9: 24VDC 입력, 50여, 표준 모델 (추천)

3PS477.9: High-power alternative

CPU Controllers (Select as required)

3CP340.60-1

3CP360.60-1

3CP380.60-1

3CP382.60-1

Communication Interface Modules (3IF Series)

3IF661.9: RS232+RS485

3IF671.9, 3IF672.9: 할 수 있다 / Serial interfaces

3IF789.9: 프로피버스-DP

3IF791.9: X2X Link expansion bus

Backplane Carriers (3BP Series, select slot quantity)

3BP152.4: 5-slot carrier

3BP155.4: 8-slot carrier

3BP180.4: 12-slot carrier

4. Analogue Expansion Modules (선택 과목)

3AI375.6: Analogue input module

3AI775.6: Multi-channel analogue input module

3AM050.6 / 3AM055.6: Analogue output module

Important Procurement Terms (Forward to suppliers together)

1. Series requirement: 비&R System2005 series. Full model suffix must be confirmed, no abbreviations. Distinguish 3DO479.6 / 3DO487.6 to avoid incorrect delivery.
2. Supply status: Original production discontinued. Priority to confirm surplus new stock or fully tested used units; modules must pass power-on and channel function testing prior to delivery.
3. Terminal compatibility: Only 3TB170.9 / 3TB170.91 fit 3DO479.6; other TB series terminals cannot be mounted.
4. 전기적 사양: 3DO479.6 is NPN Sink output with no software channel diagnostics. Do not interchange directly with diagnostic-equipped 3DO487.6.
5. Long-term retrofit suggestion: New projects are not recommended to adopt System2005. Recommended replacement model: X20DO4649 (Hardware incompatible; backplane, wiring and PLC program modifications required).

Simplified Spare Parts Inquiry Template (Direct Copy for RFQ)

Requirement List:

1. 3DO479.6 × ___ pcs
2. 3TB170.9 (나사식 터미널) × ___ pcs

OR 3TB170.91 (스프링 터미널) × ___ pcs

Requirements: All units to undergo power-on and channel output function testing before shipment.