Привод для машин ABB ACS355-01E-02А4-2

ABB ACS355 series general machinery drive, 0.37 кВт / 0.5 HP, single-phase 200–240 V input, защита IP20, rated output current 2.4 А. Suitable for speed control and energy-saving operation of small machinery.

1 Пояснение кода модели

2 Ключевые технические данные

3 Ключевые особенности

3.1 Flexible Control

Predefined application macros: constant torque, fan/pump, PID control, и т. д..

Local/remote control switching via keypad, terminals or fieldbus

Built-in PID controller for closed-loop flow, давление, и т. д..

3.2 Reliable Protection

Перегрузка по току, перегрузка, перенапряжение, пониженное напряжение, перегрев, phase loss protection

Motor over-temperature protection (requires external PTC)

Short-circuit and earth-fault protection

3.3 Easy Operation

Compatible control panel with ACS350/510/550 series

Parameter copy function for fast commissioning

среднее время безотказной работы > 100,000 hours for continuous operation

4 Типичные применения

Малые конвейеры, упаковочное оборудование

Фанаты, насосы (small HVAC systems)

Миксеры, centrifuges and small processing machines

Автоматические двери, roller shutters

Medical equipment, laboratory instruments

Textile, printing and other light industrial machinery

5 Установка & Руководство по вводу в эксплуатацию

5.1 Требования к установке

Must be installed in an enclosed electrical cabinet

Температура окружающей среды: 0–40°C (derate 10% at 40–50°C)

Монтировать вертикально, keep ≥ 100 mm clearance above and below for cooling

Avoid dust, масло, corrosive gases

Input protection: 10 A MCCB (C-кривая) or fuse recommended

5.2 Basic Commissioning Steps

1. Pre-power check: Verify wiring (L1/N input, U/V/W output), оконечный крутящий момент, proper earthing
2. Parameter initialization

Group 99: set motor rated voltage, текущий, власть, скорость

Select application macro (Стандартный, ПИД, и т. д.)

3. Control configuration

Local control: via control panel

Remote control: via DI terminals or optional Modbus RTU

4. Тест работы

No-load test: run at 5–10 Hz, check rotation and stability

Load test: gradually apply load, verify current and temperature

Adjust acceleration/deceleration time (1–10 s recommended)

6 Cross-Brand Replacement Options (0.37 кВт, 1-фаза 220 В, IP20)

7 Выбор & Maintenance Tips

7.1 Recommended Options

Braking function: optional braking resistor (75 Ой / 50 W recommended)

Коммуникация: add RS485 module

Enhanced EMC: additional input EMC filter

7.2 Обслуживание

Clean cooling channels every 6 месяцы

Check terminal torque annually

Avoid frequent starts/stops (≤ 20 times per day)

Температура хранения: -25°С до +60°С, dry environment

ABB ACS355-01E-02А4-2

Installation and Commissioning Manual

Обзор: This manual provides complete instructions for safety, installation, проводка, parameter setting and commissioning of the ACS355-01E-02A4-2 drive (0.37 кВт / 0.5 HP, single-phase 200–240 V) for general machinery speed control and energy saving.

1 Safety Instructions (Обязательно прочтите)

1.1 Электробезопасность

Power-off procedure: Disconnect all power before installation, wiring or maintenance. Wait 5 minutes for internal capacitors to discharge.

Earthing: PE terminal must be reliably earthed (earth resistance ≤ 4 Ой)

Защита от перегрузки по току: Install 10 A MCCB (C-кривая) or fuse on input side

Испытание изоляции: Only test motor cables; do NOT apply voltage to the drive itself

1.2 Mechanical Safety

Rotating parts (shaft, coupling, pulley) must be guarded

Mount vertically on solid surface to avoid vibration

Do not modify internal circuits or structures

1.3 Environmental Safety

Рабочая температура: 0–40°C (derate 10% at 40–50°C)

Влажность: 5–95% RH, неконденсирующийся

IP20: must be installed in enclosed cabinet

2 Product Overview and Model Identification

2.1 Модель Объяснение (ACS355-01E-02А4-2)

2.2 Основные характеристики

3 Installation Procedure

3.1 Подготовка

1. Unpack and inspect drive for damage
2. Choose well-ventilated, dust-free location inside cabinet
3. Инструменты: крестовая отвертка (PH2), wire stripper, crimping tool, мультиметр, insulation tape

3.2 Монтаж

1. Mount vertically on flat metal plate
2. Keep ≥ 100 mm above/below, ≥ 50 mm left/right clearance
3. Fix with M4 screws, момент затяжки: 1.2–1.5 N·m

4 Electrical Wiring

4.1 Terminal Description (ACS355-01E Series)

4.2 Этапы подключения

1. Power wiring: L1/N to mains, PE to earth, U/V/W to motor
2. Control wiring (Standard macro example):

DI1: Forward (FWD), DI2: Reverse (REV), DI3: Перезагрузить

AI1: Speed reference (0–10 V)

3. Check torque, изоляция, and phase sequence

5 Parameter Settings

5.1 Keypad Functions

▶/■: Начинать / Останавливаться

▲/▼: Adjust value

ENTER: Confirm

ESC: Back

LOC/REM: Local / Удаленный

5.2 Quick Motor Settings (Group 99)

5.3 Common Application Parameters

6 Commissioning Flow

6.1 Pre-Power Check

Correct power and control wiring

Motor and drive area clear

Cabinet ventilation OK

Input voltage: 200–240 V single-phase

6.2 First Power-Up

Close MCCB, display shows REM or LOC

Check for fault codes

Verify Group 99 motor parameters

6.3 Motor Identification (Необязательный)

Set 9910 = 2 (ID Run)

Press ENTER; drive runs motor briefly

Completed when shown COMPLETE

6.4 No-Load Test

Switch to LOCAL

Run at 5 Гц, check rotation

Increase to rated frequency, check noise and vibration

6.5 Нагрузочный тест

Switch to REMOTE

Control speed via AI1

Check output current ≤ 2.4 А

Adjust acc/dec to avoid overcurrent

Test protection functions

7 Поиск неисправностей

7.1 Распространенные коды неисправностей

7.2 Typical Issues

8 Обслуживание

8.1 Регулярное техническое обслуживание

Clean cooling channels every 6 месяцы

Check terminal torque annually

Log operating current and temperature

8.2 Long-Term Storage

Температура: -25°С до +60°С

Dry, ventilated environment

Power on for 1 hour every 6 месяцы

9 Appendix: Options and Replacements

9.1 Recommended Options

Braking resistor: 100 Ой / 50 Вт

EMC filter

RS485 Modbus RTU module

Shielded cable for control wiring

9.2 Кросс-брендовые альтернативы (0.37 кВт, 1-фаза 220 В, IP20)

Manual Version: V1.0 (based on ABB official ACS355 manual, adapted for ACS355-01E-02А4-2)

Effective Date: February 2026

Copyright: ABB Group, Все права защищены