AIRTAC DMSE-PNP Cylinder Magnetic Sensor

Complete standard model: DMSE-P020 / DMSE-P030 / DMSE-P050, commonly referred to as DMSE-PNP in the industry. E-profile slot type, 3-wire PNP output, non-contact electronic cylinder magnetic sensor.

Определение модели

DMSE-P020

DMS: Electronic magnetic sensor series

Э: E-profile (fits E-slot of АРКТИКА SE / SAE series cylinders)

П: 3-wire PNP output; N = NPN output

020: Cable length 2 m; 030 = 3 m; 050 = 5 m

Connector version: DMSE-PM08 (M8 male connector, 0.5 m cable)

Основные электрические характеристики

3-Wire Wiring Definition

Коричневый: DC24 V Positive

Синий: 0 V Negative

Черный: Выходной сигнал PNP (connect to PLC input terminal)

ПНП-выход: High-level signal (приблизительно. напряжение питания) on black wire when magnet is detected. Suitable for PLC sinking-type input terminals.

Compatible Cylinders

Specially designed for E-slot cylinders: SE, SAE series cylinders.

Cannot be directly mounted on SC / SDA cylinders. SC uses G-profile DMSG; SDA uses J-profile DMSJ, corresponding mounting brackets are required.

Comparison within the Same Series

1. DMSE-Pxxx: E-slot, for SE/SAE cylinders, ПНП; DMSE-Nxxx = NPN version
2. DMSG-Pxxx: G-slot, for SC/SGC cylinders
3. DMSJ-Pxxx: J-slot, for SDA/TCL cylinders
4. DMSH-Pxxx: H-slot, for ACQ compact cylinders

Рекомендации по выбору

1. Confirm cylinder groove profile: Э / Г / Дж / ЧАС; wrong profile prevents installation.
2. PLC input type: PNP output matches PLC sinking-type input.
3. Длина кабеля: 2 m(020), 3 m(030), 5 m(050); M8 connector version supports quick harness plug-in.
4. Advantages of electronic type: Высокочастотная работа, длительный срок службы. No mechanical contacts compared with CMS reed-switch series, suitable for high-speed reciprocating motion.

Common Replacements

Отечественная альтернатива: Domestic E-profile PNP magnetic sensor with parameters DC5-30V, 200 мА, E-section profile.

Взаимозаменяемый: DMSE-P020 ↔ DMSE-P030 differ only in cable length.

AIRTAC DMSE-PNP (DMSE-P020) Установка

Direct-mount type: Fits E-shaped slot of SE / SAE cylinders; no extra bracket required, clip directly into the side E-groove of cylinder barrel.

Step-by-Step Installation Procedure

1. Ослабьте установочный винт: Use small flat-blade screwdriver to turn the set screw on sensor head counter-clockwise (do not remove it completely).
2. Slide into groove: Insert DMSE sensor from the end of the E-shaped side groove on SE/SAE cylinder barrel. Keep flat bottom surface of sensor tight against groove base.

⚠️ Only for SE, SAE cylinders with E-slot. Not applicable for SC/SDA or other slot-profile cylinders.

3. Position adjustment: Manually move cylinder piston, slide magnetic sensor to desired detection position (signal triggers when piston magnet ring passes this position).
4. Tighten and fix: Fasten the head set screw

Recommended torque: 0.15-0.20 Н·м, maximum ≤0.25 N·m. Excessive torque will crack plastic housing.

Important: Screw tip must NOT protrude from sensor bottom surface; otherwise it will jam and scratch cylinder groove.

5. Verification test: Manually cycle cylinder piston to confirm reliable signal triggering. Re-adjust screw if position needs fine-tuning.

Installation for Cylinders without E-slot

If your cylinder is non-SE/SAE without E-shaped groove:

DMSE has no universal hoop bracket and cannot be fitted directly. Select magnetic sensors with corresponding profile (DMSG / DMSJ / DMSH) and use dedicated mounting brackets.

Электропроводка (3-wire PNP)

Коричневый: DC24 V+

Синий: 0 В / Земля

Черный: Выходной сигнал PNP (connect to PLC sinking-type input point)

Key Installation Notes

1. Cylinder must be equipped with built-in magnet ring, otherwise magnetic sensor cannot detect signal.
2. Prevent cable from following cylinder reciprocating movement; reserve cable slack. Minimum bending radius ≥19 mm to avoid cable fatigue fracture.
3. Keep away from strong magnetic fields (solenoid coils, welding equipment etc.) во избежание ложного срабатывания.
4. Do not use sensor as mechanical stop. Cylinder shall be equipped with built-in buffer; forbid piston impact onto sensor.
5. Retighten screws periodically. Equipment vibration may cause position shift.

Быстрое устранение неполадок

Нет выходного сигнала: ① Verify cylinder has magnet ring; ② Check whether sensor aligns with piston magnet ring; ③ Over-torque causing housing deformation; ④ Reversed power-supply wiring.

Ложное срабатывание: Strong surrounding magnetic interference; too-small spacing between two magnetic sensors.

AIRTAC DMSE-PNP (DMSE-P020) Выходные характеристики

Тип выхода: 3-wire PNP, transistor output, Нормально открытый (НЕТ), sourcing output

Level Logic

When cylinder magnet ring is detected: Signal wire (черный) outputs high-level voltage nearly equal to supply DC24 V.

No magnet detected: Signal wire is high-impedance state (нет вывода).

Электропроводка

1. Коричневый: DC24 V positive
2. Синий: DC0 V negative
3. Черный: PNP signal output terminal

PNP sourcing output: Sensor sources 24 V voltage outward.

✅ Совместимость: PLC sinking-type input module

❗Caution: Cannot connect directly to PLC sourcing-type input, signal will not be recognized.

Electrical Output Specifications

Output structure: Bipolar transistor, non-contact electronic design

Max load current: 200 мА

Load voltage range: DC5-30 V

Max load power: 6 Вт

Режим вывода: Factory preset Normally Open (НЕТ), no Normally Closed version available

Частота ответа: 1000 Гц, suitable for high-frequency cylinder reciprocation

Load Connection Methods

1. Connect to PLC sinking-type input: Black wire connects to PLC input channel; PLC common COM terminal connects to 24 V-. When magnet is detected, input channel receives 24 V and PLC turns ON.
2. Connect to relay coil: One end of relay coil connects to black signal wire; the other end connects to 0 V. Relay energizes upon magnet detection.

Распространенные недоразумения

1. DMSE-Pxx: PNP sourcing output; DMSE-Nxx: NPN sinking output.
2. This is electronic sensor, not dry-contact relay. It requires DC power supply; cannot be used as passive switch.
3. Without piston magnet ring, no signal will be generated regardless of wiring.

Simple memory rule: PNP outputs high-level voltage; NPN pulls signal down to 0 V.

AIRTAC DMSE-PNP (DMSE-P020) Спецификация материала

DMS-series electronic magnetic sensor, divided into housing, кабель, крепежные детали, internal potting compound.

1. Sensor Main Housing

Материал: Impact-resistant PBT engineering plastic (Белый корпус, blue cable retainer ring also PBT).

Properties: Impact-resistant, wear-resistant, resistant to general oil contamination; operating temperature-10 ℃ ~ +70 ℃; IP64 protection; 50 G shock resistance.

Примечание: Пластиковый корпус; tightening torque shall never exceed 0.25 N·m, over-torque causes cracking.

2. Output Cable (Standard A05 General-purpose Version)

Jacket: High-flexibility PVC grey cable, 3-core copper conductors, anti-bending performance for robot / cable-chain applications.

A06 oil-resistant version: Special oil-resistant cable (yellow retainer ring, IP68), model suffix -W for DMSE-P-W oil-resistant & waterproof variant.

3. Set Screw

Stainless steel flat-head machine screw, for locking sensor into cylinder E-slot.

4. Internal Construction

Magnetic sensing components + PCB circuit board, epoxy resin potting. Circuit is fully sealed inside plastic housing to achieve dust-proof and water-proof performance.

DMS is electronic type, no reed-switch glass tube. (CMS series adopts reed-switch glass tube).

Version Differentiation

1. Standard DMSE-P020: PBT housing + PVC high-flex cable, IP64, blue cable retainer.
2. Oil-resistant waterproof DMSE-P020-W: PBT housing + oil-resistant cable, yellow retainer ring, IP68, suitable for cutting-fluid and splash-water environments.

Material-Related Usage Precautions

1. PBT housing shall avoid immersion in strong acid, strong alkali and strong solvents.
2. PVC cable shall avoid contact with strong organic solvents, otherwise accelerated aging and cracking will occur.
3. Plastic housing shall not suffer hard-object impact or knocking.