Fluke 376-FC AC/DC Clamp Meter

FC Meaning: счастливая случайность-Соединять, Bluetooth wireless connection, supporting mobile APP data logging, trend graphing and on-site report generation.

Part of the 370-FC series industrial-grade clamp meters. Supplied standard with an 18-inch iFlex flexible current probe (optional for 375-FC).

Основные характеристики

Ключевые особенности

1. VFD Low-pass Filter: Optimized for VFD output measurements, suppresses carrier-frequency interference for accurate motor-drive readings; not available on 374-FC.
2. In-Rush Surge / Starting Current Mode: Filters noise to accurately capture motor inrush current, matching real-world conditions seen by protective devices.
3. Fluke-Connect Bluetooth Wireless: Remote readings via mobile device, регистрация данных, trend curves, on-site PDF report generation; ShareLive video call for collaborative troubleshooting, keeping users away from arc-flash hazards.
4. Мин / Макс / Average recording: Captures intermittent fault fluctuations.
5. iFlex Flexible Coil: Enables measurements in confined spaces and on large-diameter cables without cable disconnection.

Стандартный упаковочный лист

376-FC clamp meter main unit

i2500-18 iFlex flexible current probe (18-дюйм)

Test leads and test probes

TPAK magnetic hanging strap

Мягкий чехол для переноски

User manual and safety manual

Сравнение серий (374-ФК / 375-ФК / 376-ФК)

Совет по выбору: Choose 376-FC for 1000A AC/DC, frequent VFD testing, high-current work and wireless logging. Choose 375-FC for applications within 600A.

Типичные применения

Industrial motors, variable-frequency drives, distribution panels, UPS, Фотоэлектрические инверторы

Plant electrical maintenance, equipment commissioning, диагностика неисправностей, motor inrush-current testing

On-site remote reading, data archiving and test-report generation

Использование & Примечания по техническому обслуживанию

1. The iFlex flexible coil measures AC only, DC measurements must use the meter’s physical jaws.
2. Enabling the VFD filter reduces bandwidth; disable it for standard power-frequency measurements.
3. In-Rush mode captures transient startup events and shall not be used for steady-state readings.
4. Second-hand inspection checklist: Undamaged jaws, intact iFlex coil, functional Bluetooth, sound lead insulation, valid calibration status.

Fluke 375-FC vs 376-FC Key Differences

Both support Fluke-Connect Bluetooth, VFD filter, In-Rush mode, DC-mV and True-RMS, with identical safety ratings. Differences lie in jaw current range, iFlex inclusion and crest factor.

Plain-language Explanation

1. 375-ФК: 600A upper limit

Suitable for most low-voltage distribution panels, motors and loads up to 400A. iFlex coil is sold separately. Cost-effective for routine plant maintenance where 600A is sufficient.

2. 376-ФК: 1000A jaw + factory-fitted iFlex

Designed for 800-1000A loads, шины, high-power UPS and high-power VFDs. Ready-to-measure up to 2500A AC out-of-box with no extra probe purchase.

⚠️ Note: iFlex flexible coil measures AC only. High DC current must be measured by the meter’s built-in jaws.

Руководство по выбору

Most operating conditions ≤600A, rare high-AC-current work → 375-FC

Frequent 800-1000A measurements, regular large-AC-current testing, no wish to buy iFlex separately → 376-FC

Second-hand Purchase Notes

Many used 375-FC units do not include iFlex. Genuine complete 376-FC units come with the i2500-18 flexible coil.

For both models verify: VFD filter function, In-Rush mode, Bluetooth connectivity, jaw movement and lead insulation integrity.

Различия в приложениях: Fluke 375-FC vs 376-FC

Feature sets are nearly identical: VFD filter, In-Rush surge, Fluke-Connect Bluetooth and DC-mV are all present. Application gaps stem from two core points:

① Maximum jaw current: 600A AC/DC for 375-FC; 1000A AC/DC for 376-FC

② iFlex is factory-supplied on 376-FC but must be purchased separately for 375-FC.

🟢 375-FC Application Scope (600A jaw, iFlex optional)

For general-purpose plant maintenance with steady-state load current ≤600A and rare >600A DC measurements.

1. Medium-small VFD-driven motors: 30-200 kW motors, MCC cabinets; measure operating current, startup inrush and VFD output (VFD filter enabled).
2. General low-voltage distribution panels: Feeder circuits, ≤400A molded-case breaker loops; routine inspection and preventive maintenance with data logging.
3. DC-side work: DC power panels, small-capacity UPS and DC busbars, for DC currents no higher than 600A.
4. Коммерческие здания, HVAC and general equipment commissioning: iFlex probe may be purchased later if occasional high-AC-current measurement is needed.
5. Maintenance teams: Majority circuits sit below 600A; cost-optimized choice when iFlex is not used daily.

⚠️ 375-FC Limitations

Jaw DC measurement is capped at 600A. DC above this value cannot be measured (iFlex works for AC only).

Flexible coil is not supplied; extra procurement required for large cables or tight-fit busbar measurements.

🔴 376-FC Application Scope (1000A jaw, iFlex standard)

Targets high-current scenarios, frequent 600-1000A AC/DC measurements and regular flexible-probe usage for large cables / шины.

1. Heavy-duty industrial motors: 200-450 kW motors with operating current at or above 600A; motor inrush testing and high-power VFD circuit diagnostics.
2. High-power UPS, low-voltage busbars and incoming cabinets: Transformer secondary and 800-1000A incoming-feed circuits; direct high-DC-current readings via main jaws.
3. PV and energy-storage PCS converters: Mixed AC-DC environments; capable of near-1000A DC readings which cannot be achieved by the 375-FC.
4. Frequent iFlex-probe deployments: Congested cable trays, busbars and oversized cables that cannot fit within standard jaws; 2500A-AC measurement capability available immediately out-of-box.
5. System integration, project commissioning & EPC sites: Mixed-spec loads covering low-ampere loops through kilo-ampere incoming feeds; one-meter coverage; remote readings for test-reporting and arc-flash hazard mitigation.

⚠️ 376-FC Caveat

iFlex remains AC-only; 1000A DC is measured exclusively through the physical meter jaws.

Справочник по быстрому выбору

Common Field Pitfall Reminder

The iFlex flexible probe measures AC only.

👉 High DC current must always use the meter’s hard jaws regardless of model; flexible coils offer no DC capability.

Therefore for energy-storage / PCS DC-side currents above 600A, the 375-FC will overflow; 376-FC is mandatory.