Контактор,автоматический выключатель,датчик,Кодер,ПЛК,Конвертер
PR18S-BC10DNO is an M18 cylindrical plastic housing diffuse-reflective photoelectric sensor from LANBAO (Шанхай Ланбао Зондирование) Серия PR18S. It adopts a dedicated control IC for stable performance and integrates multiple circuit protections. Rated IP67 for dust and water resistance, it is a general-purpose object detection component widely used in industrial automation. It comes standard with a 2-meter PVC cable (суффикс: -Е2).
- Расшифровка кода модели
The full standard model is PR18S-BC10DNO-E2. The definition of each code is as follows:
PR18S: Серия продуктов, featuring M18×1 thread, PBT plastic housing and diffuse-reflective detection principle
BC10: Detection specification
BC: Диффузно-отражающий (direct reflection) detection mode
10: Rated sensing distance of 10cm (зафиксированный, нерегулируемый)
Д: Power supply type, DC 10~30VDC
Н: Тип выхода, НПН
О: Выходная логика, Нормально открытый (НЕТ; output turns on when an object is detected)
-Е2 (Default suffix): Кабельный вывод, standard 2m PVC cable; suffix -C stands for M12 4-pin connector type
- Основные технические характеристики
| Категория | Спецификация |
| Detection Mode | Диффузное отражение (direct reflection) |
| Источник света | 880nm Infrared LED |
| Номинальное расстояние срабатывания | 10см (на основе 90% reflectivity white card, нерегулируемый) |
| Напряжение питания | 10 ~ 30 В постоянного тока |
| Тип выхода | 3-wire NPN Normally Open (НЕТ) |
| Максимальный ток нагрузки | ≤300mA |
| Текущее потребление | ≤25mA |
| Время ответа | ＜8.2ms |
| Точность повторения | ≤5% Sr |
| Диапазон гистерезиса | 3% ~ 20% Sr |
| Функции защиты | Защита от обратной полярности, защита от короткого замыкания, защита от перегрузки, surge protection |
| Индикатор состояния | Желтый светодиод (lights up when object is detected) |
| Материал корпуса | PBT Engineering Plastic |
| Габаритные размеры | M18×1 thread × 53.5mm (body length) |
| Класс защиты | IP67 (Compliant with IEC Standard) |
| Рабочая температура | -15℃ ~ +55 ℃ |
| Влажность окружающей среды | 35% ~ 95%RH (без конденсации) |
| Сертификаты | CE, UL |
- Full Model List of DC Diffuse-Reflective Sensors in the Same Series
| Расстояние срабатывания | НПН НЕТ | НПН НК | ПНП НЕТ | ПНП НК | NPN NO+NC | PNP NO+NC |
| 10см (Нерегулируемый) | PR18S-BC10DNO | PR18S-BC10DNC | PR18S-BC10DPO | PR18S-BC10DPC | PR18S-BC10DNR | PR18S-BC10DPR |
| 40см (Регулируемый) | PR18S-BC40DNO | PR18S-BC40DNC | PR18S-BC40DPO | PR18S-BC40DPC | PR18S-BC40DNR | PR18S-BC40DPR |
Примечание: All models are equipped with -E2 (2м кабель) по умолчанию; replace the suffix with -C for connector version.
- Определение проводки (3-wire Cable Version)
Brown wire: Мощность положительная (+10~30 В постоянного тока)
Blue wire: Power negative (0В / Земля)
Black wire: Выходной сигнал (НПН НЕТ; output conducts when object is detected, connect to the negative side of load)
- Типичные применения
Workpiece presence detection and counting on automated production lines
Material detection for packaging and printing industries
Object recognition and sorting trigger on warehouse conveyor lines
Limit positioning and home position detection for equipment stations
Missing part and falling part detection for small components
- Матрица поиска и устранения распространенных неисправностей
| Явление неисправности | Первопричина | Пошаговые решения |
| Indicator off and no output after power-on | 1. Обратная полярность питания | 1. Check brown and blue wires and rewire correctly |
| 2. Supply voltage out of 10~30VDC range | 2. Measure supply voltage with multimeter to ensure it is within rated range | |
| 3. Internal cable breakage | 3. Replace cable or conduct cross test with spare sensor | |
| No signal output even when object is detected | 1. Object beyond effective sensing distance | 1. Reduce the distance between sensor and object with proper margin |
| 2. Low reflectivity of measured object (pure black / light-absorbing material) | 2. Use high-reflective surface or select 40cm long-distance model | |
| 3. Wrong wiring of output circuit | 3. Verify complete connection of black output wire and load circuit | |
| Ложное срабатывание & continuous output with no object | 1. Highly reflective objects in background | 1. Adjust mounting angle to avoid reflective background |
| 2. Strong ambient light directly irradiating the receiver lens | 2. Install light shield to block strong direct light | |
| 3. Severe electromagnetic interference | 3. Route sensor cables away from power cables and ensure proper grounding | |
| Fluctuating and unstable output signal | 1. Object stays at the detection boundary | 1. Fine-tune mounting distance to stay away from critical zone |
| 2. Dust or dirt covering the lens | 2. Clean the lens with a soft dry cloth |
- Альтернативные модели
Upgraded model of the same brand: PR18-BC10DNO (Nickel-copper alloy metal housing with higher mechanical strength, идентичные электрические параметры)
Межбрендовые эквивалентные альтернативы: OMRON E3Z-D61, Schneider XUB5BNANL2
PR18S-BC10DNO is a standard M18 plastic housing diffuse-reflective photoelectric sensor manufactured by LANBAO. See physical specifications below:
- Detailed Mounting Dimensions
This sensor adopts threaded cylindrical mounting. Dimensions and mounting regulations are specified as follows:
| Элемент | Спецификация |
| Main Thread | M18 × 1mm (Metric fine thread) |
| Effective Thread Length | 30мм |
| Sensor Body Length (Excluding cable/connector) | Приблизительно. 53.5мм (cable version) |
| Sensing Face Diameter | Φ18mm |
| Стандартные аксессуары | 2 шт. Контргайки M18, 1 pc anti-loose washer |
| Recommended Mounting Hole | Φ18.5mm through hole |
| Minimum Spacing for Side-by-Side Installation | ≥40mm (to prevent optical crosstalk) |
Инструкции по монтажу
- Fix the sensor on cabinet panels, brackets and other mounting positions via two lock nuts; the extension length is adjustable.
- Align the sensing face towards the moving direction of measured objects. The tilt angle is recommended ≤15°, otherwise the effective sensing distance will be reduced.
- This is a non-flush mount sensor. Do not embed the sensing face into metal mounting surface; keep the sensing face fully exposed.
- Определение проводки & Connection Instructions
9.1 Standard Cable Version (Suffix -E2, 2m PVC Cable, 3-проволока)
| Цвет провода | Функция | Описание |
| Коричневый | Мощность Позитив (В+) | Connect to 10~30VDC positive terminal |
| Синий | Мощность отрицательная (Земля) | Connect to power 0V / negative terminal |
| Черный | Выходной сигнал (ВНЕ) | NPN нормально открытый (НЕТ) выход |
9.2 Wiring Principle of NPN NO Output
This model is NPN sinking output:
When no object is detected: Output terminal is floating, internal transistor cuts off with no signal output.
When object is detected: Internal transistor turns on, black output wire connects to blue power negative terminal and outputs low level (0В).
Типичная проводка (Connect to PLC Sinking Input)
Brown wire → 24V+ of switching power supply
Blue wire → 0V of switching power supply & PLC common terminal (КОМ)
Black wire → PLC digital input terminal
Wiring for Relay / Indicator Load
One end of load connects to 24V+, the other end connects to sensor black output wire.
Sensor blue wire connects to 24V-.
Single-channel load current shall not exceed 300mA. Для индуктивных нагрузок, connect a freewheeling diode in reverse parallel.
9.3 M12 Connector Version (Suffix -C, 4-pin Male Connector)
Назначение выводов (View from sensing face, numbered clockwise):
- Приколоть 1: Коричневый (Власть +)
- Приколоть 3: Синий (Власть -)
- Приколоть 4: Черный (Выходной сигнал)
- Приколоть 2: Запасной (Неиспользованный)
- Монтаж & Меры предосторожности при подключении
- Polarity Protection: Do not reverse power polarity. The built-in reverse polarity protection prevents burnout, but the sensor will not work normally under reversed connection.
- Load Limit: Maximum output load current is 300mA. Do not drive high-power loads directly; use intermediate relays for transition.
- Экологические требования: Avoid direct sunlight or strong LED light on the sensing window, and keep away from mirror or polished metal reflective surfaces in the background.
- EMC Requirements: Separate sensor cables from power cables (инвертор, servo cables) with a distance of ≥20cm. Do not lay them in the same conduit.
