OMRON F3SG-4RE1630P30 Световая завеса безопасности

Application Scenarios of ОМРОН F3SG-4RE1630P30 (1630mm Height, 30mm Hand Protection, Type4 PL e)

This light curtain features 1.63m protective height and 30mm detection resolution dedicated to hand protection, with highest safety Category 4 / СИЛ 3. It has no muting function and only basic OSSD outputs, suitable for equipment requiring physical barrier to stop hands entering hazardous areas, covering machining, автоматизация, логистика, резина & пластик, robot industries:

Stamping & Forging Equipment (Core High-Risk Applications)
Safety protection for operating openings of air/hydraulic presses
Safety isolation at feed inlets of press brakes & plate shears
Material pick-up stations for hot & cold forging machines

Функции: 1630mm height fully covers hand intrusion range of standing operators; configurable with manual reset + EDM monitoring to meet machine tool safety standards.

Разбивка кода модели

Модель: F3SG-4RE1630P30

Сегмент	Код	Определение
F3SG	Ряд	F3SG-R Basic Safety Light Curtain (Entry-level model; no muting, no cascade function)
4	Safety Type	Тип 4 highest safety rating, ПЛ е / СИЛ 3 / Категория 4
RE	Подсерия	RE = Basic simplified version; no muting, no cascade, no beam coding, only basic safety outputs
1630	Protected Height	Effective protective height: 1630 мм
П	Тип выхода	Dual PNP OSSD safety outputs
30	Разрешение	30mm hand protection, beam pitch 20mm, minimum detectable opaque object: φ30mm

Электрическое ядро & Характеристики безопасности

2.1 Mandatory Safety Certifications

МЭК 61496-1: Тип 4

ИСО 13849-1: ПЛ е / Категория 4

МЭК 61508: СИЛ 3

Соответствует EN 60204-1, Категория 0 machine safety stop

2.2 Optical Detection Parameters

Protected Height: 1630 мм

Beam Pitch: 20 мм

Total Beams: 80 beams

Minimum Detectable Opaque Object: φ30 mm (hand protection grade)

Detection Range: 0.3 м ~ 20 м

Maximum Response Time: 9 РС

Synchronization: Optical synchronization, no dedicated sync wiring required

2.3 Электрические параметры

Напряжение питания: 24 В постоянного тока ±20 % (SELV Safety Extra Low Voltage)

Выходы безопасности: 2-channel PNP OSSD, max load per channel: 300 мА

Residual Voltage: ≤2 V

Ток утечки: ≤1 mA

Transmitter Current Draw: ≤120 mA; Receiver Current Draw: ≤150 mA

Разъем: M12 straight plug; Transmitter: 5-приколоть, Получатель: 8-приколоть, factory fitted with 0.3m short cable

2.4 Относящийся к окружающей среде & Механические свойства

Габаритные размеры: 35(Вт) × 35(ЧАС) × 1630(л) мм

Защита от проникновения: IP67 (when connectors fully tightened)

Рабочая температура: -10 ℃ ~ +55 ℃

Температура хранения: -25 ℃ ~ +70 ℃

Влажность: 35%~85% RH, неконденсирующийся

Устойчивость к вибрации: 10~55 Гц, amplitude 0.7mm, 20 cycles per 3 топоры

Ударная устойчивость: 100 м/с², 1000 shocks per 3 топоры

Материал корпуса: PBT engineering plastic; Optical window: PC polycarbonate

Вес нетто (Transmitter + Receiver Set): ~1.2 kg

Описание функции (Limitations of RE Basic Series)

✅ Standard Built-in Functions

Two independent OSSD safety outputs; outputs cut off immediately upon beam occlusion
DIP switch selectable: Auto-reset / Manual-reset, EDM external device monitoring enable/disable
Красный & Green LED status indicators (Власть, Sync, Occlusion, Вина)
Long-distance mode optimized for detection range 10~20 m

❌ Неподдерживаемые функции (Not available on RE basic model)

Muting function

Multi-unit cascade connection

Anti-interference beam coding

Auxiliary signal output (only dual safety outputs available)

M12 Connector Pin Definition

Transmitter (5-pin M12)

1: 24V DC+

2: 0V GND

3: Optical Sync

4: Неиспользованный

5: Щит

Получатель (8-pin M12)

1: 24V DC+

2: 0V GND

3: OSSD1 PNP Output

4: OSSD2 PNP Output

5: EDM Monitoring Input

6: Reset Input

7: Optical Sync

8: Щит

Типичные сценарии применения
Perimeter safety protection for industrial robot workcells
Hand protection for stamping & injection molding machine operating zones
Safety isolation at inlet/outlet of automated conveyor lines
Human intrusion detection for large machine tools & assembly lines with 1.6m protective height
Safety light curtain for AGV traffic aisles in warehouses
Optional Matching Accessories (Ordered Separately)
F39-JD□RA: M12 extension cables (5m/10m/20m)
F39-BT Standard Mounting Bracket, F39-BTLP Long Bracket
F39-SG Splash Guard (for environments with cutting fluid & тяжелая пыль)
F39-LZ Laser Alignment Tool (fast calibration for long-distance installation)
Alternative Replacement Models
Direct drop-in equivalent (same specs): F3SG-4RE1630N30 (NPN output version)
Upgraded SR series (long-term supply recommended): F3SG-4SR1630-25 (Тип 4, расширенные функции, supports muting & cascade)
Lower safety Type 2: F3SG-2RE1630P30 (PL d, not applicable for high-risk pressing machinery)
Установка & Руководство по вводу в эксплуатацию
Minimum mounting distance between light curtain and hazard zone ≥0.3m; calculate safety distance matching machine braking time
Optical alignment after installation: steady green LED = normal operation; flashing LEDs indicate misalignment or out-of-range distance
EDM external monitoring must be enabled for high-risk equipment to detect safety relay contact welding faults
Reset mode configuration: Manual reset mandatory for presses/stamping machines; auto-reset allowed for conveyor lines
Avoid direct intense light irradiation on optical windows to prevent infrared interference and false triggering
Quick Troubleshooting Matrix

Явление неисправности	Первопричина	Решение
Steady red LED, no safety output	Beam occlusion, misaligned transmitter/receiver, сломанный кабель	Clean optical window, realign light curtain, inspect M12 connectors
Alternating red & green flashing	Distance out of 0.3~20m range, strong light interference	Shorten installation distance, install light shield, activate long-distance DIP switch
Locked state after power-up, cannot reset	Open EDM circuit, incorrect DIP switch settings	Check feedback wiring of safety relay, reset DIP switches
Safety outputs fail to cut off load	Excessive load current, inductive load without freewheeling diode	Reduce load current, install freewheeling diode parallel to inductive loads

Injection Molding & Die Casting Equipment

Open pick-up ports replacing safety doors for vertical & horizontal injection molding machines
Feeding & part extraction windows for aluminum & zinc alloy die-casting machines
Operating station isolation for rubber vulcanizers & экструдеры

Приложение: Manual loading/unloading of mold products, preventing hands entering clamping & extrusion hazard zones.

Machining Industry
Open loading/unloading channels for CNC milling machines & обрабатывающие центры
Manual feed side protection for lathes, шлифовальные машины & band saws
Manual loading stations for sheet metal & fiber laser cutters

Преимущества: IP67 dust & liquid resistance, tolerates cutting fluid and metal dust; 30mm resolution prevents finger intrusion into cutting tool hazard zones.

Industrial Robot Workcells
Access gates of 6-axis robot handling & assembly safety fences
Manual intervention channels for palletizing & welding robots
Safety passages for robot grinding & coating stations

Описание: 1.63m height fits adult standing passage; power cut-off for robots upon personnel intrusion, complies with PL e machinery safety requirements.

Automated Conveying & Packaging Lines
Входное отверстие & outlet protection for carton sealers & упаковочные машины
Hazard zone isolation for stretch wrapping & pallet strapping machines
Separation stations of production lines & manual sorting workstations
Dual-side safety light curtains for AGV & forklift traffic aisles

Working Condition: Auto-reset configurable for assembly lines; machine stops upon accidental intrusion and resumes automatically after personnel leave.

Литиевая батарея & 3C Electronic Automation Equipment
Manual operation windows for battery slitting & намоточные машины
Feed inlets of phone housing CNC & pressing equipment
Open stations for battery testing & assembly machines

Преимущества: 24V SELV low voltage eliminates electric leakage risk; low electromagnetic interference compatible with precision electronics production lines.

Warehouse & Logistics Lifting Equipment
Side safety protection for small freight elevators & lifts
Manual access openings of automated racking systems
Hazard gap isolation for roller conveyors & transfer machines
Wood & Stone Processing Machinery
Feed inlet protection for sliding table saws, sanders & stone cutting machines
Operating zone isolation for wood door & panel polishing equipment

Неподходящие сценарии применения (Limitations of RE Series)

Processes requiring material passing through protective area (Muting function unavailable; machine stops when any workpiece passes, F3SG-SR series recommended instead)
Multi-curtain splicing via cascade connection (RE series does not support cascade)
Long-term vehicle & large workpiece access passages (Muting function mandatory to avoid frequent unexpected shutdowns)

Response Time Parameters of OMRON F3SG-4RE1630P30