Phoenix MCR-C-UI-UI-DCI-2810913

1. Model Code Breakdown Explanation

2. Core Specification Data Sheet

2.1 Basic Electrical Specifications

2.2 Механический & Environmental Specifications

2.3 Сертификация & Согласие

3. Full Series Part Number List (MCR-C-UI-UI-DCI Family)

4. Cross-reference: Obsolete & Competitor Replacement List

4.1 Internal Phoenix Replacement

4.2 Cross-brand Equivalent Comparison

5. Среда применения & Отраслевые случаи

5.1 Recommended Applications

1. Промышленная автоматизация: Signal isolation between PLC and field sensors/actuators to eliminate ground loop interference
2. Process Industry: Safe transmission of analog signals for chemical, фармацевтический, еда & beverage in explosion-proof environment
3. Новая Энергия: Pitch control monitoring for wind turbine, PV inverter signal acquisition, substation remote signaling renovation
4. Железнодорожный транзит: Signal isolation for train control & on-board equipment with superior EMC resistance
5. Очистка воды: PLC automation system for municipal water plant, safe integration of process sensor signals

5.2 Not Recommended Applications

1. Intrinsically Safe hazardous area (Select MCR-EX intrinsic safety series instead)
2. Ultra-low temp (<-20°С) or ultra-high temp (>+65°С) среда
3. Special project requiring isolation voltage higher than 1.5kV
4. High-frequency signal processing above 30Hz bandwidth

5.3 Типичные случаи применения

Случай 1: Automotive Production Line

Приложение: Signal isolation for welding robot controller & pressure transmitter

Проблема: Severe EMI from welding current causes distorted sensor readings

Решение: Install MCR-C-UI-UI-DCI isolator, 1.5kV galvanic isolation, conversion error＜0.1% to guarantee precise pressure control

Случай 2: Municipal Wastewater Treatment Plant

Приложение: Conversion & isolation between pH sensor and PLC analog input

Проблема: Different equipment ground potential drift leads to unstable output

Решение: Adopt 3-port isolation to cut ground loop; convert 0–10V sensor signal to standard 4–20mA for up to 1000m long-distance cabling

6. Selection Tips & Quick Reference Rules

Правила быстрого выбора

1. Model Identification: MCR-C=standard size; UI=universal I/O; DCI=DC galvanic isolation
2. Ключевые характеристики: 3-way isolation @1.5kV, 0–10V/4–20mA, 0.1%FS accuracy,11ms step response
3. Вариант обновления: Compact space saving → MACX MCR series PN:2811284
4. Application Rule: Ground loop trouble →3-port isolation; long cable run →4–20mA output
5. Air Shipment Compliance & CE Certification Summary

7.1 Air Transport Compliance

Lithium Battery Check: No built-in lithium cell, classified as non-restricted goods without special shipping marking

Классификация транспорта: Complies with IATA DGR Class9, acceptable as general cargo

Упаковка: Original factory carton preferred; ESD bag protection recommended

7.2 CE Certification Info

Applicable Standards: EN61000-6-2 (Иммунитет), EN61000-6-4 (Эмиссия)

DOC Download: EU Declaration of Conformity available on Phoenix official website (Doc No.:083097087_04_DoC_EU.pdf)

Valid Scope: All EU member states & regions accepting CE marking

8. Руководство по устранению неполадок

Phoenix MCR‑C‑UI‑UI‑DCI (2810913) On-site Installation Manual

1. Safety Precaution (Mandatory Reading)

Класс защиты: IP20, indoor dry cabinet installation only

Выдерживать напряжение: In-Out 1.5kV AC/60s; Power-Signal 1kV AC/60s, overvoltage withstand test prohibited

Защита от ЭСР: Static-sensitive component; discharge body static by touching grounded metal before handling

Hazardous Area: Suitable for Zone2 / Class I Div.2 only; MCR‑EX IS series for Intrinsically Safe location

Источник питания:18–30V DC (Nominal 24V DC); reverse polarity will permanently damage unit, confirm polarity prior to power-up

2. Unpacking & Inspection

2.1 Packing List

Isolation amplifier MCR‑C‑UI‑UI‑DCI (2810913) ×1

This installation manual ×1

Factory test certificate ×1

2.2 Visual Check

No housing crack, intact snap latch, non-deformed & rust-free terminals

Confirm model & part No.: MCR‑C‑UI‑UI‑DCI / 2810913

3. Среда установки & Clearance Requirement

3.1 Ambient Condition

Рабочая температура: -20°C ~ +65°C

Температура хранения: -25°С ~ +70°С

Влажность:10%~90% non-condensing

Min.30cm clearance away from strong EMI source (ЧРП, large motor, трансформатор)

3.2 Mounting Spacing

Mount: Standard 35mm DIN rail (EN60715), any mounting direction allowed

Side gap between adjacent modules ≥5mm

Vertical top/bottom clearance ≥20mm for heat dissipation & обслуживание

Install at upper/middle cabinet position; avoid dusty bottom compartment

4. DIN Rail Mount & Dismount Steps

4.1 Монтаж

1. Clean DIN rail from grease & burr, ensure reliable rail grounding
2. Flip upward the orange top latch of module
3. Hook upper notch onto top edge of DIN rail then press down module bottom
4. Audible click sound confirms locked & fixed without wobble

4.2 Dismounting

1. Cut off module power & all field signals first; no live removal allowed
2. Lift orange release latch upward
3. Lift module bottom upward to detach from DIN rail then take out
4. Определение терминала & Спецификация проводки

5.1 Terminal Pinout (Left to Right)

5.2 Wiring Standard

Cable strip length:8мм (too long → short circuit; too short → poor contact)

Размер проводника: Solid/Flexible 0.2–2.5mm² (AWG24–14); ferrules required for stranded flexible wire

Screw torque:0.5~0.6N·m for M3 terminal, avoid over-tightening thread slip

Shield cable: Single-end cabinet grounding (transmitter end floating) to eliminate ground loop

5.3 Typical Wiring Examples

Ex1: 4–20mA Input →4–20mA Output (2-wire transmitter)

Transmitter + →1.2(IN I)

Transmitter − →1.3(GND1)

2.2(OUT I) →PLC AI+

2.3(GND2) →PLC AI−

3.1→24V DC+;3.2→24V DC−

Ex2:0–10V Input→0–10V Output (Voltage sensor)

Sensor +→1.1(IN U)

Sensor −→1.3(GND1)

2.1(OUT U)→PLC AI+

2.3(GND2)→PLC AI−

3.1→24V DC+;3.2→24V DC−

6. DIP Switch Configuration (Factory preset for 2810913:0–10V/0–10V)

6.1 Switch Location (Side housing; remove cover to access)

S1: Input Configuration

S1‑1:OFF=0–10V; ON=4–20mA

S1‑2:OFF=Unipolar; ON=Bipolar(±5V/±10V)

S2: Конфигурация выхода

S2‑1:OFF=0–10V; ON=4–20mA

S2‑2:OFF=Unipolar; ON=Bipolar(±5V/±10V)

6.2 Factory Default (2810913)

S1:OFF/OFF (Unipolar 0–10V Input)

S2:OFF/OFF (Unipolar 0–10V Output)

6.3 Setting Procedure

1. Cut off power supply then remove 2 cross-head screws to open cover
2. Toggle DIP switches as required with fully seated position
3. Refit housing & tighten screws before power-on test
4. Power-up & Commissioning

7.1 Pre-power Inspection (Обязательный)

Full wiring check: No cross-connection, short circuit or loose terminal

DC supply test: 24V DC ±10% measured across pin3.1 &3.2

Isolation test: No continuity between Input/Output/Power with multimeter continuity mode

7.2 Светодиодная индикация состояния

PWR(Зеленый): Steady ON=Normal Supply; OFF=Power fault/reverse polarity

RUN(Зеленый): Blinking=Running normally; Solid/OFF=Module malfunction

7.3 Калибровка (Optional for high precision requirement)

Zero Adjustment: Feed zero input signal, trim ZERO potentiometer for zero output

Span Adjustment: Feed full-scale input, trim SPAN potentiometer for full-scale output

Точность: ≤0.1%FS, max temperature drift ≤±2%

8. On-site Quick Troubleshooting

8.1 Power LED Dark

Причина: Reverse polarity, abnormal voltage, свободная проводка | Action: Correct polarity, measure voltage, retighten terminals

8.2 Zero Output Signal

Причина: Неправильная проводка, mismatched DIP setting, перегрузка | Action: Перемонтировать, reset switches, check load impedance

8.3 Unstable Swinging Output

Причина: Improper shield grounding, high supply ripple, nearby EMI | Action: Single-point ground, install power filter, relocate away from interference source

8.4 Out-of-spec Accuracy

Причина: Thermal drift, zero/span shift, mismatched load | Action: Recalibrate, улучшить вентиляцию, adjust load

9. Periodic Maintenance

Every 6-month routine: Power off to clean terminal/housing, recheck screw torque & recalibrate accuracy

Forbidden operation: Hot plug/unplug, overvoltage/overtemperature running, unauthorized internal circuit disassembly

10. Техническая поддержка & Alternative Part

Manufacturer Support: Phoenix Contact China

Upgrade Replacement: MACX MCR‑UI‑UI (2811284):12.5ширина мм, lower power consumption, faster response speed