Schneider 3-pole main contacts LC1D38BD

Schneider TeSys Deca series, 3-главные контакты полюса, 24Катушка постоянного тока. Designed for motor start/stop, HVAC and automation control cabinets. Встроенные вспомогательные контакты 1НО+1НЗ..

✅ Model Code Definition

ЛК1: Standard contactor

Д: ТеСис Д (Дека) ряд

38: Rated operational current 38A @ AC-3, 400В

БД: 24Катушка постоянного тока В (integrated coil surge suppression)

📌 Key Electrical Specifications

🛠️ Typical Applications

Прямой онлайн, star-delta and forward/reverse control of 3-phase asynchronous motors

системы отопления, вентиляции и кондиционирования, водяные насосы, фанаты, воздушные компрессоры

Оборудование автоматизации, packaging machinery and production line control cabinets

Direct coil drive by PLC 24VDC digital outputs (no intermediate relay required)

🧩 Compatible Accessories

Тепловое реле перегрузки: серия ЛРД (LRD35…), snap-fit directly below the contactor

Вспомогательный контактный блок: LA1DN (for extra NO/NC contacts)

Модуль механической блокировки: LA9D4001 (for forward/reverse interlock)

Подавление перенапряжений: Integrated inside coil, no external component needed

🔁 Alternative & Compatible Selection

1. AC coil variants within the same series: LC1D38M7 (220ВАК), LC1D38B7 (24ВАК)
2. Отечественная альтернатива: CJX2-3811 DC24V (note differences in dimension, terminals and mechanical life)

⚠️ Важно: BD = 24VDC, B7 = 24VAC. Coils are NOT interchangeable.

📋 Certifications & Стандарты

МЭК 60947-1/-2/-4-1, CCC, cULus. Complies with IEC60335-1 flame retardant standard and A2L refrigerant safety certification for HVAC.

🧪 Second-hand Inspection Checklist

1. Катушка: Continuity check on A1/A2. Apply 24VDC; armature pulls in without noise or overheating.
2. Основные контакты: L1/L2/L3 ↔ T1/T2/T3. Conductive when closed, high resistance when open; inspect contact erosion.
3. Вспомогательные контакты: 13-14(НЕТ), 21-22(Северная Каролина). Switch synchronously with main contacts.
4. Механический: No sticking; housing free of cracks or carbon blackening.

HS Code Reference

8536410000 (Electromagnetic contactor, voltage ≤60V)

Typical Engineering Application Cases for LC1D38BD

Core advantages: Катушка постоянного тока 24 В, direct PLC drive without intermediate relay; built-in surge suppression and certified mirror NC contact; 18.5kW max 3-phase motor @ AC-3, 50A for AC-1 resistive loads

Случай 1: Chilled water pump DOL start for HVAC BMS (Building Automation System)

Нагрузка: 15kW 3-phase chilled water pump, 380В, motor rated current ≈28A

Схема управления: ПЛК (Сименс / Schneider M241) DO directly drives LC1D38BD 24VDC coil

Главная цепь: 3P circuit breaker → LC1D38BD → LRD35 thermal overload relay → pump motor

Логика управления: BMS outputs 24VDC based on water temperature/pressure differential to energize contactor and start pump. Built-in 1NO auxiliary contact feeds running status back to PLC; built-in mirror NC contact for fault acquisition.

Обоснование выбора: DC coil provides strong anti-interference. BMS cabinets commonly adopt DC24V control. Wide temperature range -5~+60℃ suits high-temperature equipment rooms. 45Узкий корпус мм экономит место в шкафу.

Аксессуары: LRD35 thermal relay (28~36A), Монтаж на DIN-рейку.

Случай 2: Air compressor motor control (OEM machinery manufacturer)

Нагрузка: 18.5kW screw air compressor main motor, 400В

Схема управления: PLC directly drives LC1D38BD with pressure switch interlock for shutdown

Схема: Circuit breaker → LC1D38BD → LRD thermal relay → air compressor motor

Функции: Частый старт-стоп (Макс 3600 циклов/час). DC coil pulls in stably without AC hum. Built-in coil surge suppression protects PLC output points against back EMF.

Примечание: AC-3 operation reaches the 38A rating limit. Derating evaluation is recommended for heavy-duty frequent cycling.

Случай 3: Water treatment — duty/standby mutual interlock control cabinet for sewage lift pumps

Нагрузка: Two 15kW sewage pumps, duty-standby auto-switching by liquid level

Конфигурация: 2 × LC1D38BD + LA9D4001 mechanical interlock module

Логика: Pump starts on high liquid level. If main pump trips (thermal relay fault), PLC automatically switches to standby pump. Mechanical interlock prevents simultaneous closure and short circuit.

Safety feature: Built-in mirror NC contact for safety loop and fault diagnosis, meeting water treatment control cabinet safety specifications.

Приложение: Municipal sewage, factory circulating water, rainwater lift pumping stations.

Случай 4: Forward/reverse circuit for conveyor motors in packaging machinery / производственные линии

Нагрузка: 11~15kW belt conveyor motor requiring forward and reverse rotation

Конфигурация: 2 × LC1D38BD (KM1 forward, KM2 reverse) + LA9D4001 mechanical interlock

Контроль: PLC 24VDC digital outputs drive each contactor coil separately. Electrical interlock (using built-in NC auxiliary contacts) plus mechanical interlock provides double protection to prevent power short circuit.

Преимущество: DC coil has better EMI immunity than AC coils in workshops dense with inverters and sensors, reducing accidental pull-in faults.

Случай 5: Star-delta reduced voltage starting for 18.5kW dust extraction fan

Нагрузка: 18.5kW dust removal fan with high inrush current, star-delta starting adopted

Конфигурация: 3 × LC1D38BD, serving as main contactor, star contactor and delta contactor respectively

Логика: PLC outputs 24VDC sequential control; star reduced-voltage start first, then time-delayed switch to delta full-voltage operation. Built-in contactor auxiliary contacts provide status feedback and electrical interlock.

Примечание: High inrush current occurs at delta switching in star-delta circuits; contact life must be reviewed.

Случай 6: AC-1 resistive load: Industrial heating module control

Нагрузка: 3-phase heating elements, total resistive load ≤33kW (AC-1 50A @400V)

Особенность: Resistive load has no starting inrush current. AC-1 rated 50A capacity higher than motor duty. PLC 24V DO directly controls heating circuit on/off.

Приложение: Духовки, constant temperature units, process heating equipment.

Случай 7: Cleanroom air handling unit for medical facilities (medical HVAC)

Нагрузка: 15kW supply air fan for operating room clean air conditioning

Функции: Medical equipment demands high reliability and low EMI. LC1D38BD DC coil with built-in surge suppression, no electromagnetic noise from AC coils. Complies with IEC60335 HVAC safety standard, suitable for A2L refrigerant HVAC equipment, widely used in hospital BMS control cabinets.

Общий выбор & Construction Key Points (Valid for All Cases)

1. DC coil critical note: BD = 24VDC, MUST NOT be connected to AC24V. PLC output capacity must meet coil power consumption (~15VA).
2. Вспомогательные контакты: Built-in 1NO (running feedback) +1Северная Каролина (mirror safety contact, NOT for normal latching). Add LA1DN auxiliary contact block for more contacts.
3. Защита от перегрузки: Must be fitted with LRD thermal overload relay, set per motor nameplate current and shall not exceed motor rated current.
4. Utilisation category distinction

АС-3 (normal motor start-stop): 38А, max 18.5kW @400V

АС-1 (pure resistive heating): 50А

АС-4 (frequent jogging, plug braking): требуется снижение номинальных характеристик

Not Suitable Applications

Direct-on-line starting of 3-phase motors above 18.5kW (АС-3)

High-power capacitor switching (use dedicated LC1DxxKQ capacitor contactors)

Взрывоопасные зоны (explosion-proof series required)

LC1D38BD (TeSys D DC Coil) Контур & Монтажные размеры

Without attached accessories (вспомогательные контакты, тепловое реле, механическая блокировка), Версия катушки постоянного тока

Outline Dimensions (Ш × В × Г)

45 мм × 85 мм × 92 мм

Ширина: 45мм (DIN rail module, 1 module unit)

Высота: 85мм

Глубина: 92мм (from mounting backplate to front face)

Panel screw mounting holes (DC coil specific, round holes for M4)

Horizontal center distance between two holes: 35 мм

Vertical center distance between two holes: 70 мм

Screw size: М4, two round holes (⚠️ AC coil LC1D38M7 uses slotted holes; mounting layout differs from BD DC version)

Монтаж на рельсе

Совместим со стандартной DIN-рейкой 35 мм. (TH35-7.5), установка на клипсе, no drilling required.

Cabinet Layout Recommendations

1. Mounting LRD thermal relay at bottom: overall height increases; reserve adequate clearance.
2. Mounting LA1DN auxiliary contact block on top: extra depth and height required.
3. Multiple contactors side-by-side: 45ширина мм, can be mounted tightly on rail without gap. Reserve heat dissipation gap for high-temperature environments.

Operating Principle of Schneider LC1D38BD Contactor

LC1D38BD is an electromagnetic contactor with DC coil (Серия TeSys D). Essentially, it is a remotely controlled electrical switch driven by 24VDC electromagnet, using low DC signal to switch high-power 3-phase main circuit.

1. Basic Structure
2. Electromagnetic actuation section (Катушка А1/А2): 24V DC excitation coil, fixed core, moving armature, возвратная весна
3. Основные контакты (power circuit L1/L2/L3 → T1/T2/T3): 3 pairs of normally-open main contacts, rated 38A AC-3, carrying high current for 3-phase motors / heating loads
4. Вспомогательные контакты (обратная связь по сигналу): Built-in 1NO (13-14)+1Северная Каролина (21-22) mirror auxiliary contacts for status feedback and electrical interlock
5. Дуговая камера: Extinguishes electric arc when main contacts open, protecting contacts from rapid erosion

✅ Key feature for BD model: DC coil with integrated surge suppressor.

2. Full Operating Sequence

2.1 Катушка под напряжением (Pull-in action)

Apply DC24V to A1 and A2 via PLC or external control circuit:

DC coil generates constant magnetic field, magnetizing fixed core, overcoming return spring force and pulling in moving armature.

Armature drives contact carrier synchronously:

3 pairs of main NO contacts close → 3-phase main circuit energized, motor/load powered on

Auxiliary contacts switch simultaneously: 13-14(НЕТ) закрывается; 21-22(Северная Каролина) открывается

Characteristic of DC coil: constant current after pull-in, no vibration or hum from AC coils.

2.2 Coil De-energized (Drop-out action)

DC24V control signal removed:

Magnetic field of coil disappears, return spring pulls armature back.

All main contacts open, cutting high-current main circuit.

Auxiliary contacts reset: 13-14(НЕТ) открывается; 21-22(Северная Каролина) restores closed state.

Built-in surge suppression absorbs back EMF generated at coil de-energization, protecting upstream PLC output points.

3. Core Differences Between DC Coil (БД) and Conventional AC Coil
4. катушка переменного тока: operates on alternating magnetic field, prone to vibration and hum; высокий пусковой ток; contact bounce under voltage fluctuation.
5. LC1D38BD DC24V coil:

Stable magnetic field, armature free of vibration, тихая работа

Pull-in current ≈ holding current, low inrush

Built-in freewheeling suppression, ideal for direct PLC DO drive

Disadvantage: Must never connect to AC supply; AC input burns coil immediately.

4. Typical Functions of Auxiliary Contacts

1НЕТ (13-14): Running status feedback to PLC to detect contactor pull-in state

1Северная Каролина (21-22, mirror contact): Цепи безопасности, fault detection, electrical interlock (forward/reverse circuits)

⚠️ Mirror contact property: NC contact cannot close when main contacts are welded shut, complying with safety circuit requirements.

5. Mandatory Protection Logic for Engineering

The contactor only performs switching and has NO overload protection:

Fit LRD thermal overload relay in main circuit: on motor overload, thermal relay NC contact opens contactor coil circuit to cut motor power.

Circuit breaker installed upstream: fast short-circuit protection for main power supply.

One-sentence summary:

Apply DC24V to A1/A2; electromagnetic force actuates internal contacts to close high-power 3-phase main circuit. Remove 24V supply; spring resets and opens main circuit. Low-voltage 24V signal remotely switches high-power loads. Auxiliary contacts provide status feedback and safety interlock.