Контактор,автоматический выключатель,солнечный инвертор,электрический счетчик,солнечные батареи
This is a low-inertia (high dynamic performance) серводвигатель из Сименс SIMOTICS S-1FL6 series. It is specially matched with SINAMICS V90 series servo drives to form a cost-effective and high-dynamic servo system.
The motor features a rated power of 0.75 кВт, rated torque of 2.39 N·m and rated speed of 3000 об/мин. It is equipped with a built-in TTL incremental encoder (2500 pulses per revolution). The output shaft is designed with parallel key and without holding brake. Its protection class reaches IP65 (with standard shaft seal). With fast response, high acceleration and stable operation, it is ideal for various motion control applications requiring superior dynamic performance.
Разбивка кода модели
| Сегмент кода | Описание |
| 1FL6 | General servo motor series SIMOTICS S-1FL6, standardly matched with SINAMICS V90 drives |
| 42 | Размер кадра: shaft height 40 мм, low-inertia type, corresponding to 0.75 номинальная мощность кВт |
| 2AF21 | Electrical specification: |
| 2 = 200~240 V three-phase AC power supply | |
| A = Incremental TTL encoder, 2500 pulses per revolution | |
| F = Standard industrial version | |
| 21 = Hardware interface standard version | |
| 1АА1 | Mechanical configuration: |
| 1 = Output shaft with parallel key, tolerance class N | |
| A = Without holding brake | |
| A = Straight power connector + straight encoder connector |
Основные технические параметры
- Производительность & Электрические параметры
| Элемент | Спецификация |
| Номинальная мощность | 0.75 кВт |
| Номинальный крутящий момент | 2.39 N路m |
| Stall Torque | 2.39 N路m |
| Номинальная скорость | 3000 об/мин |
| Maximum Permissible Speed | 5000 об/мин |
| Номинальный ток | 2.6 А |
| Peak Current | 7.8 А (3 times of rated current) |
| Torque Constant | Приблизительно. 0.92 Nm/A |
| Номинальная рабочая частота | 200 Гц |
| Источник питания | 200 ~ 240 V three-phase AC |
- Механический & Параметры окружающей среды
| Элемент | Спецификация |
| Rotor Moment of Inertia (without brake) | 0.351 × 10⁻⁴ kg·m² |
| Flange Shaft Height | 40 мм |
| Output Shaft Type | Plain shaft with parallel key, tolerance class N |
| Класс защиты | IP65 (Standard shaft seal equipped) |
| Ambient Operating Temperature | 0 ~ +40 ℃ (continuous operation under rated load) |
| Тип монтажа | Фланцевый монтаж, IM B5 |
| Overall Weight | Приблизительно. 2.1 кг (without holding brake) |
- Кодер & Интерфейсы
| Элемент | Спецификация |
| Тип кодера | Incremental TTL differential encoder |
| Разрешение | 2500 pulses per revolution with Z-phase zero signal |
| Signal Output | A/B/Z three-phase differential output, TTL level |
| Cable Outlet Type | Straight power connector + straight encoder connector |
| Совместимый диск | Only compatible with SINAMICS V90 200V series servo drives |
Complete Model List for the Same Frame (40 mm Shaft Height, Низкая инерция, 0.75 кВт)
| Номер заказа | Тип кодера | Конфигурация тормоза | Тип разъема |
| 1FL6042-2AF21-1AA1 | 2500-line incremental TTL | Without brake | Straight connector |
| 1FL6042-2AF21-1AB1 | 2500-line incremental TTL | С тормозом | Straight connector |
| 1FL6042-2AF21-1LA1 | 2500-line incremental TTL | Without brake | 90° elbow connector |
| 1FL6042-2AF21-1LB1 | 2500-line incremental TTL | С тормозом | 90° elbow connector |
| 1FL6042-2BF21-1AA1 | 21-bit single-turn absolute encoder | Without brake | Straight connector |
| 1FL6042-2CF21-1AA1 | 20+12-битовый многооборотный абсолютный энкодер | Without brake | Straight connector |
Matching Selection & Replacement Instructions
- Recommended Matching Drives
Pulse control version: 6SL3210-5FB10-8UF0 (0.75 кВт, 200 V class, Frame FSB)
PROFINET communication version: 6SL3210-5FE10-8UF0 (0.75 кВт, 200 V class, Frame FSB)
Voltage and power ratings must be strictly matched. Mismatched combination will trigger drive alarms and even burn out motor windings.
- Замена & Совместимость
Direct replacement with identical functions: 1FL6042-2AF21-1LA1 (only 90° elbow connector, identical electrical performance; applicable when installation space is limited)
Functional upgrade replacement: For position retention after power failure, select multi-turn absolute encoder model 1FL6042-2CF21-1AA1. The drive shall support absolute encoder protocol accordingly.
Prohibited replacement: Do not replace with high-inertia models of the same power (например. 1FL6044 series), due to incompatible shaft height, voltage and installation dimensions.
Типичные применения
Упаковочное оборудование: Film feeding, flying shear and fixed-length cutting stations for labelers, horizontal packaging machines and bag making machines
Погрузочно-разгрузочные работы: Small pick-and-place devices, linear modules and loading/unloading mechanisms for electronic components
3C assembly: High-precision positioning and high-speed reciprocating axes for screw drivers, dispensers and chip mounters
Light industry equipment: Tension and position control for screen printers, small winding machines and indexing tables
General automation: High-dynamic scenarios such as small manipulators, conveyor positioning and feeding of inspection stations
Распространенные неисправности & Troubleshooting Matrix
| Явление неисправности | Root Cause | Step-by-Step Solutions |
| Drive reports encoder fault (например. F31110) | Loose encoder connector / oxidized pins; damaged cable; electromagnetic interference; defective encoder | 1. Выключить питание, re-plug the motor-side encoder connector and check for retracted or oxidized pins. 2. Replace with a new shielded cable for testing. 3. Route encoder cables separately away from power cables and implement single-end grounding. 4. Replace the motor if hardware failure is confirmed. |
| Motor overload alarm and overheating housing | Механические помехи; excessive load inertia ratio; excessive loop gain; continuous operation under over-rated load | 1. Power off and rotate the shaft manually to eliminate mechanical sticking or excessive resistance. 2. The recommended load inertia ratio for low-inertia motors is ≤5:1. Install a reducer or switch to high-inertia model if over limit. 3. Properly reduce speed loop / position loop gain. 4. Optimize motion profile and lower continuous load rate. |
| Vibration and abnormal noise during operation | Improper control parameter tuning; loose coupling/flange; encoder signal interference; worn bearing | 1. Gradually reduce position loop gain to eliminate vibration. 2. Fasten mounting bolts and coupling set screws. 3. Check shielding and grounding of encoder cables. 4. If abnormal noise still exists during no-load running, inspect bearing lubrication and wear. |
| No torque output and motor fails to run after power-on | Открытая цепь / poor contact of power cables; drive enable signal disconnected; тормоз (необязательный) not released; defective drive power stage | 1. Measure voltage and continuity of three-phase power cables and fasten connectors. 2. Check enable signal from PLC and drive parameters. 3. For braked models, confirm normal 24 V power supply for brake. 4. Replace the drive to locate the faulty component. |
Standard Models of Matched V90 Drives
The model 1FL6042-2AF21-1AA1 is a 200~240 V three-phase, 0.75 kW low-inertia incremental encoder servo motor. It is exclusively matched with SINAMICS V90 drives of the same voltage and power rating. Two official standard models with different control interfaces are available, which can be directly connected and automatically identify motor parameters.
| Control Version | Full Order Number | Основные функции | Размер кадра |
| PTI Pulse Train Version | 6SL3210-5FB10-8UA0 | Equipped with pulse/direction and analog setpoint interfaces; supports USS / Modbus RTU communication; suitable for pulse control with general PLC and motion control cards | FSC |
| PROFINET Bus Version | 6SL3210-5FB10-8UF0 | Integrated dual-port PROFINET switch, supports PROFIdrive protocol; suitable for bus-based positioning control with S7-1200/1500 PLC, supports standard telegram 1/105/111 | FSC |
Key Matching Instructions
- Согласование электрических параметров
Both drives accept 200~240 V AC input (однофазный / three-phase applicable) with rated output current of 4.7 А. It fully matches the motor rated current 2.6 A and peak current 7.8 А, enabling the motor to operate at 3 times overload capacity.
- Encoder Compatibility
Both drives natively support the motor’s TTL incremental encoder (2500 lines per revolution with zero signal). No additional encoder card is required. Motor nameplate parameters can be read automatically after power-on without manual input.
- Selection Restrictions
Do not use 400 V class V90 drives (order number starting with `5FE`). Mismatched voltage will directly burn out motor windings.
It is not recommended to use drives with higher power rating. Although the motor can run, mismatched protection thresholds will lead to failure of overload protection and potential safety hazards.
Дополнительные примечания
Updated hardware models of the same power (например. suffix 8UA1, 8UF1) are only hardware revisions with identical functions and interfaces, which can be used as direct replacements. If the motor is later upgraded to absolute encoder type, no drive replacement is required; only parameter modification is needed.
Standad Order Numbers for Pre-assembled Cables
1FL6042-2AF21-1AA1 is a 200 V low-inertia servo motor with incremental encoder, no brake and straight connectors. Only power cables and encoder cables are required. Adopt Siemens MOTION-CONNECT 300 series pre-assembled cables, plug-and-play with IP65 protection class. The power cable is connected to drive via terminals, while the encoder cable uses dedicated connectors.
- Power Cables (4×2.5 mm², для 200 В 0.75 kW low-inertia motor)
Motor-side straight connector, fully compatible with motor straight outlet interface.
| Длина кабеля | Full Order Number | Спецификация |
| 3 м | 6FX3002-5CK32-1AD0 | 4×2.5 mm² shielded power cable |
| 5 м | 6FX3002-5CK32-1AF0 | 4×2.5 mm² shielded power cable |
| 10 м | 6FX3002-5CK32-1AH0 | 4×2.5 mm² shielded power cable |
| 20 м | 6FX3002-5CK32-1BA0 | 4×2.5 mm² shielded power cable |
- Encoder Cables (for 2500-line incremental TTL encoder)
Matched with built-in incremental TTL encoder, with differential shielding.
| Длина кабеля | Full Order Number | Спецификация |
| 3 м | 6FX3002-2CT20-1AD0 | 3×2×0.20 + 2×2×0.25 mm² shielded signal cable |
| 5 м | 6FX3002-2CT20-1AF0 | 3×2×0.20 + 2×2×0.25 mm² shielded signal cable |
| 10 м | 6FX3002-2CT20-1AH0 | 3×2×0.20 + 2×2×0.25 mm² shielded signal cable |
| 20 м | 6FX3002-2CT20-1BA0 | 3×2×0.20 + 2×2×0.25 mm² shielded signal cable |
- Optional Brake Cable (Not required for this motor, for reference only)
If replaced with braked motor of the same frame (например. 1FL6042-2AF21-1AB1), an extra brake cable is needed.
| Длина кабеля | Full Order Number | Спецификация |
| 5 м | 6FX3002-5BK02-1AF0 | 2×0.75 mm² shielded control cable |
Выбор & Application Notes
- Connector Matching: The above cables are equipped with straight connectors on motor side, perfectly matching motors with suffix 1AA1. For motors with elbow connectors (suffix 1LA1), select cables with the second letter B (например. 6FX3002-5CK32-1BD0).
- Length Limit: The maximum length of standard pre-assembled cables for 200 V low-inertia series is 20 м. 7 m and 15 m cables are only for 400 V high-inertia motors and not available for this series.
- Installation Scenario: MOTION-CONNECT 300 cables are designed for fixed installation. Not applicable for cable chains and continuous reciprocating motion. Select high-flexibility cables for dynamic operation.
- Спецификация проводки: Route power cables and encoder cables separately with a spacing of ≥20 cm. Implement reliable single-end grounding for shielding layer to avoid encoder signal loss or alarms caused by electromagnetic interference.
- Custom Cable Solution: For on-site customized length, purchase separate motor-side connectors for crimping: Power connector: 6FX2003-0LL13; Incremental encoder connector: 6FX2003-0SL11.
