Honeywell 2108N4000H Combustible Gas Detector - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

วีแชท: +86-13184948252 วอทส์แอพพ์: 0086-13811255435 อีเมล: kent@bestcontactor.com

เกี่ยวกับ ติดต่อ |

 Honeywell 2108N4000H Combustible Gas Detector - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

ไฟฟ้า/

Honeywell 2108N4000H Combustible Gas Detector

Honeywell Searchpoint Optima Plus (2108N4000H) ความผิดพลาด & Warning Troubleshooting Table Reading methods: ฮาร์ท 475/375 Communicator, SHC1 Handheld Interrogator, EDD Device Description File; W=Warning, F=Fault. Under fault condition, output defaults to 0mA (this HART version can be set to 1mA). Some faults are latched and require manual clearing or power cycle reset. Error Code Status English ...

  • รายละเอียดสินค้า

ฮันนี่เวลล์ Searchpoint Optima Plus (2108N4000H) ความผิดพลาด & Warning Troubleshooting Table

Reading methods: ฮาร์ท 475/375 Communicator, SHC1 Handheld Interrogator, EDD Device Description File; W=Warning, F=Fault. Under fault condition, output defaults to 0mA (this HART version can be set to 1mA). Some faults are latched and require manual clearing or power cycle reset.

Error CodeสถานะEnglish Nameคำอธิบายข้อผิดพลาดOn-site Troubleshooting StepsLatched
0ว / เอฟTemperature Limit ExceededOperating temperature near or out of -40~+65℃ range1. Measure ambient temperature of the detectorเลขที่
2. Check direct sunlight or overheating from heat tracing
3. ปรับปรุงการระบายอากาศ & shading; relocate if over-temperature
4ว / เอฟBad 24V SupplySupply voltage outside 18~32VDC operating range1. วัดแรงดันไฟฟ้าที่ขั้วต่อภายใต้โหลด (not no-load power supply)เลขที่
2. Check cable voltage drop, short circuit and wire gauge
3. Verify power capacity and restart the loop
5ว / เอฟBad 4-20mA LoopAnalogue output deviation >0.5มิลลิแอมป์, cannot output correct signal1. ตรวจสอบขั้ว, shielding grounding and loop resistance✅ Latched
2. Avoid hot-plugging multimeter probes
3. วงจรไฟฟ้า; if fault remains, output circuit is damaged
6ว / เอฟNegative Gas ReadingNegative zero drift of gas reading1. Confirm clean atmosphere with no hydrocarbon gasเลขที่
2. Remove dust filter and clean optical window
3. Perform zero calibration; eliminate condensation and solvent interference
8ว / เอฟObscured Optics (Optical Contamination)เลนส์ & gas chamber blocked by oil, dust or water vapour, optical path attenuation1. Remove weather shield and dust barrierเลขที่ (frequent warning)
2. Wipe optical window with lens paper and anhydrous ethanol
3. Dry and reset; check heating function if heavy condensation
11ว / เอฟLow Lamp OutputInfrared lamp power degraded, end-of-life aging1. Clean optics first to rule out contaminationเลขที่
2. If alarm persists after reset: replace optical module due to lamp failure
13เอฟHardware FaultSelf-test failure of main board and drive circuit1. ปิดเครื่องเพื่อ 5 minutes then re-power✅ Latched
2. ทำให้แหล่งจ่ายไฟมีเสถียรภาพ
3. Recurring fault: return for repair or replace transmitter
16เอฟPoor Signal QualityNoisy, unstable infrared signal with low SNR1. Clean optical window and filter first✅ Latched
2. Check water ingress or frost inside gas chamber
3. Replace optical assembly if lamp aging or optical offset occurs
22ว / เอฟInternal Firmware FailureFirmware checksum error, memory exception1. Full power cycle restart✅ Latched
2. Clear fault log via HART tool
3. Persistent error: re-flash firmware or replace main board

📌 Common General Faults (No independent Error ID in HART)

  1. HART Communication Failure

ตรวจสอบ: 250Ω HART resistor must be installed on the loop; correct polarity; single-end shield grounding; no excessive non-HART devices on the bus; matching baud rate.

  1. Slow reading drift with no error code

ตรวจสอบ: overdue calibration; clogged dust filter; continuous low-level hydrocarbon interference; heavy oil adsorption inside gas cell.

  1. No current output & no communication after power-on

ตรวจสอบ: น้ำเข้า & terminal corrosion in M25 junction box; burnt circuit due to reverse polarity; ฟิวส์ภายในขาด.

🛠️ Operation Guidelines (for 2108N4000H)

  1. Clear Latched Faults: HART menu →【Fault/Warning】→Clear; or power off ≥30 seconds then restart. Hardware faults will reoccur immediately after reset; do not mask them permanently.
  2. Calibration Precondition: Clear all optical path & lamp warnings before zero/span calibration; calibration will drift severely with active optics contamination warning.
  3. Spare Parts Division: ข้อผิดพลาด 8,11,16 = optical module (โคมไฟ + detector + lens); Error5,13,22 = main board failure. Board-level repair is not recommended; replace the whole transmitter directly.
  4. SIL2 Reminder: F-class faults trigger SIL safety loop action. Do not run the detector with fault masked for long; rectify promptly.

(Searchpoint Optima Plus)

ตำแหน่งผลิตภัณฑ์: Point-type NDIR hydrocarbon combustible gas detector, HART protocol version

Manufactured by Honeywell Analytics UK. NDIR infrared principle, immune to catalytic bead poisoning. Ideal for offshore platforms, refineries, LNG and other harsh environments; SIL2 safety integrity level.

✅ Model Coding Definition

2108: Searchpoint Optima Plus series

เอ็น: Hydrocarbon HC version (มีเทน, propane, gasoline etc., โมเดลของคุณ)

4: Standard diffusion type with weather shield

000: Without remote gas cell & sampling path

ชม: ฮาร์ท 7 protocol superimposed on 4-20mA signal (suffix N = pure 4-20mA without HART, เช่น. 2108N4100N)

ด้าย: M25 (distinguished from 41xx series with 3/4″เธรด NPT)

การกำหนดค่ามาตรฐาน: 316L electropolished stainless steel housing, dust filter, nylon weatherproof cover, sunshade against rain splash.

📌 Key Technical Specifications

รายการพารามิเตอร์
หลักการตรวจจับNon-Dispersive Infrared (NDIR)
ช่วงการวัด0~100%LEL; configurable for hundreds of hydrocarbons & solvents (มีเทน, propane, ethylene, gasoline, aromatics)
พาวเวอร์ซัพพลายDC18~32V, nominal 24VDC; max power consumption <4.5W
สัญญาณเอาท์พุต4-20มิลลิแอมป์ + HART7; Modbus RS485 multi-drop bus available with optional DX100(ม) โมดูล
Current Levels (Fault/Inhibit/Alarm)ความผิดพลาด: 0มิลลิแอมป์ (HART version configurable to 1mA); Inhibit: default 2mA; คำเตือน: default 3mA; Over-range: 20~21.5mA (default 21mA)
เวลาตอบสนอง (Methane)T50<3s, T90<4s
อุณหภูมิในการทำงาน-40℃ ~ +65 ℃
การป้องกันทางเข้าIP66 / IP67
วัสดุที่อยู่อาศัย316 สแตนเลส (CF8M); total weight approx. 1.6กก
ใบรับรองความปลอดภัยเอเท็กซ์, ไออีเอ็กซ์, เอฟเอ็ม, ซีเอสเอ; ซิล2 (IEC61508)
ความแม่นยำBaseline drift <±1%FSD (HC); <±2%FSD (ethylene)
Pressure Effect0.1% reading per mbar

✨ Infrared vs Catalytic Bead Advantages

  1. Resistant to catalytic poisons (ซิลิโคน, lead, H₂S), longer service life and extended maintenance interval
  2. Fail-safe optical self-test; no silent failure risk
  3. Works normally in inert atmosphere (catalytic sensors require oxygen)
  4. Built-in temperature control heating; anti-condensation optical window; pre-warning for lens contamination
  5. Onboard event log; support HART communicator for commissioning, calibration and diagnostics

🧾 Typical Application Scenarios

Offshore oil & gas platforms, FPSO, oil tankers, refineries, LNG/LPG filling stations, gas regulator stations, gas turbine power plants, solvent coating & printing workshops, tank farms.

📎 Cross-model Reference (for replacement & การเลือก)

2108N4000H: M25 thread, ฮาร์ท, diffusion type with weather shield (your unit)

2108N4100N: 3/4″เอ็นพีที, pure 4-20mA, ไม่มีฮาร์ท

2108N4100H: 3/4″เอ็นพีที, เวอร์ชั่นฮาร์ท

2108N5100H: Flow-through sampling type with HART, for pipeline sampling systems

⚠️ Important Notes

  1. Infrared detector only responds to hydrocarbons; cannot detect non-hydrocarbon flammable gases such as H₂, บจก, NH₃.
  2. Calibration gas must match target gas; response factor varies for different hydrocarbons.
  3. Cannot directly replace catalytic bead sensors without rechecking host logic and alarm thresholds.
  4. Consumable spare parts: optical module, dust filter and weather shield are regular wear items.

Honeywell Searchpoint Optima Plus (2108 ชุด) รายการรุ่นเต็ม

  1. กฎการเข้ารหัสโมเดล

2108เอ็น: Standard Hydrocarbon (HC) รุ่น (มีเทน, propane, gasoline etc.)

2108บี: Ethylene & solvent dedicated version (ethylene, aromatics, esters)

4หลักที่: 4 = Diffusion type; 5 = Flow-through sampling type (with gas cell)

Thread code: 0 = M25; 1 = 3/4″เอ็นพีที

คำต่อท้าย: N = 4-20mA only; H = 4-20mA + HART7 protocol

คำต่อท้าย 10 = with Remote Gas Cell (RGC); 00 = without remote gas cell

  1. 2108N Hydrocarbon Standard Models (Main Series, including 2108N4000H)

2.1 M25 thread (0) | Diffusion (4) | No RGC (00)

  1. 2108N4000N: 4-20มิลลิแอมป์, M25, diffusion, weather shield
  2. 2108N4000H: 4-20mA+HART, M25, diffusion (โมเดลของคุณ)
  3. 2108N4001N: Ethylene calibrated, M25, diffusion, 4-20มิลลิแอมป์
  4. 2108N4001H: Ethylene calibrated, M25, diffusion, ฮาร์ท
  5. 2108N4010N: HC + RGC remote test cell, M25, diffusion
  6. 2108N4010H: HC + RGC, M25, diffusion, ฮาร์ท

2.2 3/4″เธรด NPT (1) | Diffusion (4) | No RGC (00)

  1. 2108N4100N: 4-20มิลลิแอมป์, เอ็นพีที, diffusion
  2. 2108N4100H: 4-20mA+HART, เอ็นพีที, diffusion
  3. 2108N4110N: With RGC, เอ็นพีที, diffusion
  4. 2108N4110H: With RGC, เอ็นพีที, diffusion + ฮาร์ท

2.3 Flow-through sampling type (5) for sampling pipeline & pre-treatment systems

M25 thread (0)

  1. 2108N5000N: Flow gas cell, M25, 4-20มิลลิแอมป์
  2. 2108N5000H: Flow gas cell, M25, ฮาร์ท
  3. 2108N5010N: Flow type + RGC, M25
  4. 2108N5010H: Flow type + RGC, M25 + ฮาร์ท

3/4″เธรด NPT (1)

  1. 2108N5100N: Flow gas cell, เอ็นพีที, 4-20มิลลิแอมป์
  2. 2108N5100H: Flow gas cell, เอ็นพีที, ฮาร์ท
  3. 2108N5110N: Flow type + RGC, เอ็นพีที, high concentration range (0~100%vol CH₄)
  4. 2108N5110H: Flow type + RGC, เอ็นพีที + ฮาร์ท

2.4 Special XTC Marine & Multi-certified Models (44/46/48 ชุด)

  1. 2108N4400N / ชม: Diffusion, การรับรองทางทะเล, M25
  2. 2108N4600N / ชม: Diffusion, UL/FM certified, M25
  3. 2108N4601N / ชม: Ethylene calibrated, 46-type diffusion
  4. 2108N4800N / ชม: Optima Plus XTC version, M25 diffusion
  5. 2108N5400/5600/5800 N/H: Corresponding flow-through versions (44/46/48 sampling models)
  6. 2108B Ethylene & Solvent Dedicated Models (for Optima X/Z sampling systems)

Diffusion type (4)

  1. 2108B4001N / ชม: Ethylene calibrated, M25 diffusion
  2. 2108B4101N / ชม: Ethylene calibrated, NPT diffusion

Flow-through sampling type (5, only for sampling systems)

  1. 2108B5001N / ชม: Ethylene flow cell, M25
  2. 2108B5101N / ชม: Ethylene flow cell, เอ็นพีที
  3. 2108B2001N / ชม: Optima X fast-response sampling model (special gas cell)
  4. 2108B2051N: DNV marine certified version
  5. Full Series Spare Part Order Codes
  6. Optical Module: 2108D3001 (Methane), 2108D3034 (Ethylene)
  7. Remote Gas Cell (RGC): 2108B0240
  8. Flow-through Gas Cell Assembly: 2108B0282
  9. Dust Filter + Weather Shield: 2108B2337
  10. เทอร์มินัล & Junction Box: 2108B2360
  11. ตารางการเลือกด่วน (for replacement)
ประเภทการติดตั้งด้ายWithout RGC (มาตรฐาน)With RGC (Remote Test)
Wall-mounted DiffusionM252108N4000N / ชม2108N4010N / ชม
Wall-mounted Diffusion3/4″เอ็นพีที2108N4100N / ชม2108N4110N / ชม
Pipeline SamplingM252108N5000N / ชม2108N5010N / ชม
Pipeline Sampling3/4″เอ็นพีที2108N5100N / ชม2108N5110N / ชม
  1. หมายเหตุเสริม
  2. N = 4-20mA analogue only; H = HART enabled. Do not mix loop types; 250Ω resistor is mandatory for HART loops.
  3. 2108N only detects hydrocarbons; 2108B is dedicated for ethylene, esters and alcohols. Neither can detect H₂, CO or NH₃.
  4. All models meet SIL2, ATEX/IECEx/FM certification; IP67 ingress protection.

 

ก่อนหน้า:

ทิ้งคำตอบไว้

ฝากข้อความ