Norgren M/50/LSU/5V Reed-Type Cylinder Magnetic Position Switch

รายละเอียดโมเดล

M/50: ชุดผลิตภัณฑ์, cylinder magnetic proximity switch

LSU: Reed type, เปิดตามปกติ (เลขที่), with LED indicator, เต้าเสียบสายเคเบิล

5: ความยาวสายเคเบิล 5 เมตร

วี: Universal wide voltage version (10~170V AC/DC)

แอปพลิเคชันหลัก

Detect full stroke position of pneumatic cylinder pistons (extended/retracted position signals for feedback to PLCs or relays)

2. ข้อมูลจำเพาะทางไฟฟ้าหลัก

3. เครื่องกล & การติดตั้ง

3.1 Compatible Cylinders

Norgren RA/8000 and KA/8000 series profile cylinders; matching ring/clamp mounting brackets (QM/33 series), compatible with bore sizes 10/20/25/32/40/50/63/80/100mm.

3.2 วิธีการติดตั้ง

Profile T-slot cylinders: Slide switch directly into cylinder T-slot, no extra brackets required

Round tie-rod cylinders: Fixed via optional metal clamp brackets

3.3 วัสดุที่อยู่อาศัย

พลาสติกวิศวกรรม, resistant to oil contamination and industrial vibration

4. Cross-Series Selection Guide (Quick Differentiation)
5. M/50/LSU/2V: 2-meter cable, all other parameters identical to 5V variant
6. M/50/LSU/5U: 5-meter cable, low-voltage DC model (10~30VDC)
7. M/50/EHP Series: Electronic solid-state non-contact (พีเอ็นพี/เอ็นพีเอ็น), high-frequency long-life replacement for reed switches
8. สถานการณ์การใช้งาน

สายการประกอบอัตโนมัติ, เครื่องจักรบรรจุภัณฑ์, machine tool pneumatic fixtures

Stroke limit detection for material handling cylinders, position sensing for stamping equipment cylinders

Position feedback for general pneumatic actuators, compatible with AC/DC control cabinets

6. Operating Precautions
7. Reed contacts cannot drive heavy loads; an interposing relay must be used for signal transfer. Direct driving of solenoid coils is prohibited.
8. Avoid environments with strong magnetic fields or heavy electromagnetic interference from welding equipment to prevent false triggering.
9. Minimum cable bending radius ≥ 10× cable outer diameter; corrugated tubing protection recommended for continuously vibrating equipment.
10. Replace with electronic solid-state M/50 switches if ambient temperature exceeds 80℃.
11. Part Numbers for Matching Accessories

Clamp bracket for Ø20 bore: QM/33/020/22

Clamp bracket for Ø32 bore: QM/33/432/22

Quick switch retaining clip: QM/27/2/1

IMI Norgren M/50/LSU/5V Reed Magnetic Switch Official Full Installation Manual

Document Basic Information

แบบอย่าง: M/50/LSU/5V (M50LSU5V)

ประเภทสินค้า: Normally Open reed magnetic position switch, built-in yellow LED, 5m 2-core cable, wide voltage 10~170V AC/DC

Compatible Cylinders: Norgren RA/8000 & KA/8000 series T-slot profile cylinders, round tie-rod cylinders

การป้องกันทางเข้า: IP66

มาตรฐาน: ใน 60947-5-2, RoHS, เข้าถึง

Table of Contents

1. Unpacking Inspection & การตรวจสอบโมเดล
2. การติดตั้งเครื่องกล (Two Solutions: T-Slot Profile / Round Tie-Rod Cylinders)
3. Selection List for Matching Mounting Brackets
4. Electrical Wiring Specifications & Wiring Diagrams
5. ขั้นตอนการว่าจ้าง
6. ด้านสิ่งแวดล้อม & Installation Prohibitions (Critical Restrictions)
7. การแก้ไขปัญหาเมทริกซ์
8. การบำรุงรักษาตามปกติ
9. Quick Reference Technical Specifications

1 Unpacking Inspection & การตรวจสอบโมเดล

1.1 Incoming Goods Inspection

1. Verify laser-engraved model on switch body: M/50/LSU/5V; confirm 5-meter cable length
2. Inspect housing for cracks, cable root for damage, intact LED viewing window
3. เครื่องประดับ: Retaining fixing screw pre-installed on unit; clamp brackets must be ordered separately for round cylinders

1.2 คำจำกัดความของกลุ่มโมเดล

M/50: Magnetic proximity switch series

ล: Equipped with LED indicator

SU: General-purpose reed Normally Open, cable outlet type

5: 5-meter cable length

วี: Universal wide voltage model, 10~170V AC/DC

2 Mechanical Installation Operating Guide

2.1 T-Slot Profile Cylinders (Norgren RA/KA Series, Recommended Mounting)

1. Loosen flat-head fixing screw at switch tail and open clip slot
2. Fully insert switch clip into cylinder side T-slot, slide to target detection position (magnet position at cylinder full extension/retraction)
3. Fine-tune horizontal position: Optimal trigger point when yellow LED stays steadily illuminated as piston magnet passes switch
4. Tighten tail fixing screw with flat screwdriver, torque 0.8~1.0 N·m to prevent shifting from vibration
5. Route cable outlet downward or sideways; upward routing is forbidden to avoid water accumulation

2.2 Round Tie-Rod Cylinders (No T-Slot, Clamp Bracket Mounting)

1. Select matching QM/33 series metal clamp per cylinder bore size
2. Fit clamp onto cylinder barrel, pre-tighten clamp screws and slide to detection position
3. Clip M/50 switch into integrated clamp retainer, fasten switch fixing screw
4. Fully tighten clamp to prevent sliding during operation; clamp torque 1.2~1.5 N·m

2.3 Mountig Position Standards

Sensing face flush against cylinder outer wall, zero clearance, no metal interlayer

Minimum 20mm spacing between two switches on one cylinder to avoid mutual magnetic interference

Keep clear of strong magnetic inserts on cylinder end caps (buffer magnets)

3 Matching Mounting Bracket Part Number List

4 Electrical Wiring Specifications (Core Chapter)

4.1 Cable Definition (2-core PVC cable, 0.25มม.²)

Brown wire (บีเอ็น): Positive power / AC live line

Blue wire (นี้): Negative power / AC neutral line

Internal reed Normally Open contacts close circuit when magnetic ring approaches, yellow LED illuminates

4.2 Two Standard Wiring Schemes

Scheme A: Drive PLC Digital Input (ที่พบบ่อยที่สุด)

1. DC24V System: BN connected to +24V, BN wired to PLC input terminal, PLC common terminal connected to 0V
2. AC220V System: BN connected to Live (ล), BU connected to Neutral (เอ็น) of PLC AC input module

> WARNING: Max switching current of reed contacts is 0.18A; direct driving of solenoid coils is strictly prohibited!

Scheme B: Interposing Relay for Heavy Load Transfer

1. Relay coil wired in series with BN & BU circuit
2. Relay contacts control high-current loads including solenoid valves and indicator lights

4.3 Critical Wiring Restrictions

1. No energization under no-load conditions (unloaded circuit instantly burns reed contacts via electric arcing)
2. Separate signal wiring from power cables (อินเวอร์เตอร์, สายมอเตอร์), minimum 10cm spacing to avoid interference-induced false triggering
3. Minimum cable bending radius ≥10× cable outer diameter; repeated bending/pulling at cable root forbidden
4. Isolate full cabinet power supply before wiring work to avoid electric shock and contact burnout

4.4 Cable Routing Protection

Vibrating equipment: Route cables through corrugated tubing; reserve 5~8cm slack at switch cable root

Oil mist & spray environments: Wrap cable joints with waterproof tape; seal cable entry points inside control cabinets

5 Standard Full-Unit Commissioning Procedures

ขั้นตอน 1 Mechanical Position Calibration

Manually actuate cylinder piston to slide built-in magnet slowly across switch sensing zone

Magnet at detection position: Yellow LED remains continuously lit

Magnet away from detection position: LED fully off

If LED flickers, fine-adjust switch horizontal position for stable triggering without strobing

ขั้นตอน 2 Electrical Signal Testing

1. เปิดเครื่อง, measure circuit continuity via series-connected multimeter
2. Magnet in detection zone: Circuit closed (resistance near 0Ω)
3. Magnet away from detection zone: Circuit open (ความต้านทานไม่มีที่สิ้นสุด)

ขั้นตอน 3 Automated Cycle Verification

Run cylinder reciprocating cycle 10 times under no-load; confirm stable signal output at every stroke end without signal loss or false triggering

6 ด้านสิ่งแวดล้อม & Installation Prohibitions (Forbidden Operations)

1. Temperature Limit: Operating range -20℃ ~ +80℃; replace with M/50 electronic switches above 80℃
2. Magnetic Interference: Keep away from welding equipment, strong permanent magnets, เซอร์โวมอเตอร์, inverter output cables to prevent false operation
3. Impact Protection: Prohibit striking or dropping switch unit; internal glass reed tube fractures easily upon impact
4. Chemical Environments: Install protective covers in strong acid, alkali or high-concentration solvent environments; plastic housing will corrode and crack
5. Pressure Washing: IP66 rating only resists low-pressure spray; direct high-pressure water jet at cable root causes water ingress and unit failure
6. Overloaded Operation: Switching power must not exceed 10W; interposing relay mandatory for higher power loads

7 การแก้ไขปัญหาเมทริกซ์

8 Routine Maintenance Specifications

1. การตรวจสอบรายวัน: Check LED trigger status, inspect cables for abrasion or cracking
2. Weekly Maintenance: Clean oil and dust from switch surface; prevent metal debris adhesion to housing
3. Monthly Inspection: Retorque fixing screws to avoid loosening from long-term vibration
4. Semi-Annual Calibration: Verify signal stability; maintain spare replacement units for mass production line

9 Core Product Technical Specifications (Installation Reference)

ข้อผิดพลาดทั่วไป, สาเหตุ & Remedial Solutions for Norgren M/50/LSU/5V (M50LSU5V) Magnetic Switch

This reed-contact magnetic switch has four primary fault categories: no output signal, flickering signal, burnt switch body, mechanical shifting. Inherent reed switch weaknesses (susceptible to high current, heavy impact and high temperature) are the leading failure triggers.

1 ความผิดพลาด 1: LED unlit, no output signal when cylinder magnet arrives (Most Common Failure)

Potential Causes

1. Mechanical mounting offset

Loosened fixing screw shifts switch outside magnet sensing zone; excessive gap between switch and cylinder barrel.

2. Wiring faults

Broken conductors from repeated bending at cable root, loose terminal crimps, cable insulation cut by sharp metal edges leading to short/open circuits (AC/DC polarity insensitive).

3. Abnormal cylinder magnet

Fallen or demagnetized piston magnet; magnetic field cancellation from two overly closely spaced switches; interference from cylinder buffer magnets.

4. Physical damage to internal reed tube

Glass reed fractures from impact during transit or installation; permanent reed failure under prolonged temperatures above 80℃.

5. Mismatched supply voltage

Input voltage exceeds rated 170V, burning internal components.

Remedial Actions

1. Slide switch back to magnet center position, tighten screws (0.8~1 N·m torque) and mount flush against cylinder wall without gaps.
2. Cut power and test cable continuity; trim damaged cable sections and re-crimp terminals; reserve slack at cable root for strain relief.
3. Replace cylinder piston magnet; maintain ≥20mm spacing between two switches and keep clear of end cap buffer magnets.
4. Reed fractures require full unit replacement; electronic M/50/EHP switches recommended for high-temperature environments (minor faults repairable under low-temperature conditions).
5. Restrict system voltage within 10~170V AC/DC; fit voltage stabilizers for overvoltage systems.

2 ความผิดพลาด 2: Flickering LED, intermittent signals, frequent PLC false stroke detection / การสูญเสียสัญญาณ

Potential Causes

1. Loose switch mounting creates minor shifting from equipment vibration, unstable magnet detection.
2. การรบกวนทางแม่เหล็กไฟฟ้าอย่างรุนแรง: Signal cables routed in the same trunking as motor, inverter and welding power cables.
3. Degraded magnet strength narrows effective sensing range, causing flickering at threshold positions.
4. Partial internal cable conductor breakage creating intermittent open/closed circuits under mechanical strain.
5. External permanent magnets or tooling magnets counteract cylinder piston magnetic fields.

Remedial Actions

1. Retighten fixing screws; install anti-loosening washers for high-vibration equipment.
2. Run signal cables in separate conduits with minimum 10cm separation from power cables.
3. Replace cylinder built-in piston magnet.
4. Cut off damaged cable segment and re-terminate; relocate unit away from external permanent magnets.

3 ความผิดพลาด 3: Switch burns out immediately upon power-up, zero functionality after energization

Core Root Cause (Fatal Mistake for Reed Switches)

1. Direct driving of solenoid valves or heavy relay coils

Unit maximum switching power only 10W / 0.18ก; inductive surge current from solenoid coils instantly punctures reed contacts.

2. Energization with no load in circuit, contact burnout from instantaneous electric arcing.
3. Continuous contact arcing from frequent switching under AC220V operation causes contact welding and erosion.
4. Cable positive-negative short-circuit; heavy current burns internal LED and reed tube.

Remedial Actions

1. Mandatory interposing relay for signal transfer: Switch only energizes relay coil; relay contacts control solenoid valves.
2. Never energize unloaded circuits; series load must be installed before power connection.
3. Replace with non-contact electronic M/50/EHP switches (พีเอ็นพี/เอ็นพีเอ็น, zero arc wear) for high-frequency switching applications.
4. Locate cable insulation short-circuit points and reinforce insulation protection.

4 ความผิดพลาด 4: ติดต่อเชื่อม, LED permanently lit after magnet moves away, signal fails to cut off

สาเหตุ

1. Long-term overload and inductive load arcing melts reed contacts together.
2. Contact metal fatigue and welding from frequent cycling combined with high ambient temperature.
3. Excess supply voltage amplifies arcing and accelerates contact fusion.

Remedial Actions

Welded reed contacts cannot be repaired; replace entire switch unit. Fit interposing relays downstream to eliminate contact arcing.

5 ความผิดพลาด 5: Automatic sliding shift of switch during long equipment operation

สาเหตุ

1. Insufficient tightening torque on fixing screws.
2. Continuous vibration and shock from production line operation.
3. Worn T-slot retaining clips reducing clamping force.

Remedial Actions

Retighten screws to standard torque; add anti-loosening washers for vibrating equipment; replace complete switch unit if retaining clips are worn.

6 Latent Failures Induced by Operating Environment

1. สภาพแวดล้อมที่มีอุณหภูมิสูง (>80℃)

Rapid decline in reed sensitivity leading to failed triggering and drastically shortened service life; permanent unit failure under sustained high heat.

2. Immersion in oil mist or cutting fluid

IP66 rating only resists spray exposure; prolonged liquid penetration at cable root causes internal oxidation and wire breakage.

3. Corrosive chemical vapors

Plastic housing ages and cracks, moisture ingress damages reed tube and LED assembly.

7 Quick Differentiation: Reed Switch Exclusive Faults vs Electronic Switch Faults

M50LSU5V reed model unique failure modes: ติดต่อเชื่อม, burnout from electric arcing, vulnerability to high current surges, internal damage from impact shock.

Electronic M/50/EHP switches contain no moving mechanical contacts and eliminate all above faults, suited for high-frequency and high-power load applications.

Simplified On-Site Quick Troubleshooting Workflow

1. Manually cycle cylinder and observe synchronized LED on/off status to isolate mechanical positioning or magnet faults.
2. Cut power and test cable continuity with multimeter to identify broken wiring.
3. Disconnect downstream loads and test switch independently to diagnose overload burnout.
4. Re-route wiring away from inverters and motors to eliminate electromagnetic interference.