พานาโซนิค GP-XC12ML ดิสเพลสเมนต์เซนเซอร์

ภาพรวมผลิตภัณฑ์: GP-X Series eddy-current high-precision displacement measuring sensor (non-laser type). Complete set = Controller + M12 threaded sensor head GP-X12ML

Model Distinction:

GP-XC12ML: เอาต์พุต NPN

GP-XC12ML-P: เอาต์พุต PNP (suffix -P = PNP)

1. รายละเอียดรหัสรุ่น

1. แกนไฟฟ้า & Measuring Specifications

พารามิเตอร์พื้นฐาน

1. ช่วงการวัด: 0～5 mm (Full Scale F.S. = 5 มม)
2. Standard Target Material: SPCC cold-rolled steel / SUS304 stainless steel (60×60×1mm); only conductive metals can be measured; พลาสติก, glass are not detectable
3. ความเป็นเชิงเส้น: ±0.3% F.S.
4. ปณิธาน: 0.02%F.S. (with 64-times averaging enabled) → 1 ไมโครเมตร
5. อัตราการสุ่มตัวอย่าง: 25 ไมโครวินาที (40 kHz ultra-high response, suitable for high-speed rotation & vibration measurement)
6. อุณหภูมิดริฟท์: ≤0.07%F.S./℃; optimal working range: 20～60% of full scale

พารามิเตอร์ทางไฟฟ้า

พาวเวอร์ซัพพลาย: 24 โวลต์กระแสตรง ±10%, peak-to-peak ripple ≤10%; Power consumption ≤150 mA

Switch Output: Open collector, สูงสุด. โหลด 100 มิลลิแอมป์, withstand voltage 30 กระแสตรง

เอาท์พุทแบบอะนาล็อก: 0～5 V voltage output, output impedance ≈100 Ω

ระดับการป้องกัน: Sensor head IP67; resistant to splash of cutting fluid (risk of corrosion from oil products shall be noted)

อุณหภูมิแวดล้อม: -10℃ ～ +55℃

เคเบิล: Standard coaxial cable (3 ม); original extension cables are supported

การติดตั้งเครื่องกล (GP-X12ML Sensor Head)

ข้อมูลจำเพาะของเธรด: M12×1

Minimum recommended clearance (to avoid interference from surrounding metal): ≥14 mm

สูงสุด. แรงบิดที่กระชับ: 20 น.ม

⚠️ Do not over-tighten; excessive compression will damage internal coils and cause permanent failure

III. Controller Terminal Definition (GP-XC Main Unit)

1. 1: 24ในดีซี (Power Positive)
2. 2: 0วี (Power Negative / จีเอ็นดี)
3. ANA: เอาท์พุทแบบอะนาล็อก (0–5V)
4. OUT1: Comparison Output 1
5. OUT2: Comparison Output 2
6. TIMING: Synchronization Trigger Input
7. รีเซ็ต: Reset Input
8. INT P: Hold Input

คอม: Common terminal for outputs

(ประเภท NPN: COM connects to 0V; PNP type: COM connects to 24V)

1. หลักการทำงาน

High-frequency alternating magnetic field induces eddy current on metal surface. The variation of distance between sensor head and metal target changes eddy current impedance, and the controller converts impedance variation into displacement value.

✅ Advantages: Immune to oil mist, water spray and dust; no reflection interference. More suitable for harsh machining environments compared with laser displacement sensors.

❌ Limitations: Only conductive metals detectable; material compensation & calibration required for aluminum, copper and steel; non-metals cannot be measured.

1. สถานการณ์การใช้งานทั่วไป
2. Radial runout & deflection detection of machine tool spindles
3. Online inspection of bearing inner diameter and face runout
4. Stamping die clearance monitoring
5. Vibration and eccentricity measurement of motor rotors
6. Thickness and deformation measurement for automotive components
7. Dynamic displacement monitoring of high-speed rotating workpieces
8. Model Selection Reference within GP-X Series

ปกเกล้าเจ้าอยู่หัว. การติดตั้ง & Operation Prohibitions

1. Avoid collision between sensor head surface and workpiece; direct contact of metal with sensing face is forbidden
2. Sufficient clearance around the sensor head is mandatory; nearby metal will cause zero drift
3. Input sensor head ID code + 3-point calibration after replacing sensor head. Direct use without calibration leads to severe accuracy degradation
4. Long-term immersion in strong alkaline cutting fluid is prohibited; IP67 rating only protects against splashing, not submersible
5. Target metal thickness recommended ≥0.8 mm; ultra-thin metal reduces sensitivity
6. Do not sharply bend or repeatedly fold coaxial cable; fracture of internal high-frequency wire leads to signal loss

8. การแก้ไขปัญหาข้อผิดพลาดทั่วไป

1. Severe signal fluctuation: การรบกวนของโลหะโดยรอบ, damaged cable, สายดินไม่ดี
2. Continuous zero drift: Wide ambient temperature fluctuation (enable temperature compensation) or loose sensor mounting
3. Sensor head unrecognizable: Loose coaxial connector, damaged pin core, mismatched controller & sensor head
4. No analog output signal: Verify controller power supply and terminal contact quality

If required, I can provide:

1) Complete wiring schematic;

2) Step-by-step 3-point calibration procedure for controller;

3) Parameter comparison between GP-XC12ML and competitors (Keyence eddy current sensors, Micro-Epsilon);

4) Excerpts from official PDF datasheet.

การเปรียบเทียบ: พานาโซนิค GP-XC12ML VS Keyence Eddy Current Sensor VS Micro-Epsilon

Basic Specification Summary

Advantage Analysis

✅ Advantages of Panasonic GP-XC12ML

1. Fastest response at 40 กิโลเฮิร์ตซ์, superior for high-speed rotational runout and high-frequency vibration measurement
2. Equipped with two hardware comparison outputs, upper/lower limit alarm directly available without PLC calculation
3. Onboard display on controller for on-site commissioning; no PC software required
4. Stable performance under cutting oil & dust conditions; widely applied in domestic automation equipment

✅ Advantages of Keyence EX-V05

1. Flexible output options, native support for 4～20mA analog signal
2. Intuitive menu operation, low commissioning barrier
3. Adequate stock globally with short lead time

✅ Advantages of Micro-Epsilon eddyNCDT3010

1. Superior linearity and resolution, ideal for laboratory and metrology-grade measurement
2. Wide operating temperature range with lower drift under extreme temperature
3. Support for longer signal cables, suitable for large-scale machinery remote measurement

⚠️ Respective Drawbacks

1. Panasonic GP-XC12ML

No 4～20mA analog output; 0-5V voltage signal susceptible to interference over long transmission distance; temperature drift performance inferior to Micro-Epsilon.

2. Keyence EX-V05

Lower response speed; risk of missing peak data for vibration frequency >1 กิโลเฮิร์ตซ์.

3. Micro-Epsilon 3010

No hardware switch output; mandatory matching controller; price approx. double of Panasonic; PC software required for configuration, inconvenient for field debugging.

🎯 Selection Guidance

1. Prioritize Panasonic GP-XC12ML

Machine tool spindle runout, motor eccentricity, high-speed rotating workpiece inspection, stamping online monitoring; scenarios requiring hardware alarm output, high-speed sampling and convenient on-site tuning.

2. Prioritize Keyence EX-V05

Low-speed displacement monitoring, applications requiring standard 4-20mA analog signal, short delivery time requirement.

3. Prioritize Micro-Epsilon eddyNCDT

Laboratory precision measurement, wide temperature fluctuation environment, metrology-level accuracy, sufficient budget, no demand for hardware switch outputs.

Compatibility Reminder

Signal cables of the three brands cannot be interchanged. Different high-frequency coaxial impedance will cause measurement drift and excessive noise.

All three sensors cannot detect non-metals; separate calibration is required for ultra-thin metal sheets (thickness ＜0.6 mm).

Complete Operation Manual: 3-Point Linear Calibration for Panasonic GP-XC12ML

Applicable model: GP-XC12ML (ช่วงการวัด: 0～5 mm) Eddy Current Sensor

⚠️ Mandatory Preconditions:

1. 3-point calibration must be performed after sensor replacement, cable extension or target material change;
2. Prepare metal test block with identical material as workpiece, minimum dimension 60×60×1mm;
3. Complete mechanical installation; ensure no nearby metal interference around sensor head;
4. Stabilize ambient temperature; power on and preheat for 15 minutes before calibration.
5. Pre-Calibration Basic Settings
6. Input Sensor Head ID

Enter menu HEAD ID after power-up, input the 6-digit serial code printed on GP-X12ML sensor head.

Calibration without correct ID will lead to severe non-linearity and measurement drift.

2. Select Target Material

Menu MAT: Fe (Steel/SPCC), SUS (สแตนเลส), Al (อลูมิเนียม), Cu (ทองแดง).

Re-calibration is required once measurement material changes.

3. Cable Length Configuration via DIP Switch on Controller Rear

Standard 3m cable → set to 3m

Extended cable (total length ≤10m) → set to 3m+7m, power cycle to activate setting.

1. Definition of 3 Calibration Points (GP-X12ML Range 0～5mm)

Micrometer-adjusted fixture is recommended for precise positioning. Wait for stable reading before confirmation.

III. Panel Button Operation Procedure

Controller buttons: โหมด / ▲ / ▼ / ENT (ยืนยัน)

1. Under normal measuring screen, press【MODE】, orange MODE LED lights up to enter setting menu.
2. Scroll via ▲▼ to select cALIb (การสอบเทียบ), press【ENT】.
3. Screen displays P0 → attach test block tightly against sensor face (0 มม).

Wait for stable reading, press【ENT】to save zero point.

4. Screen switches to P1 → adjust gap to 2.5 mm midpoint.

After reading stabilizes, press【ENT】to save midpoint.

5. Screen switches to P2 → adjust gap to 5 mm full scale.

After reading stabilizes, press【ENT】to save full scale value.

6. After three points are logged, Stor appears; press【ENT】again to permanently save calibration parameters.
7. Press MODE to exit menu and return to measurement display.

❗ Error Code Handling

Err-Pos: Insufficient distance between calibration points, out-of-range position or undersized metal test block; reposition target.

Err-MAT: Selected material mismatches test block material; verify MAT setting.

1. Single-Point Zero Reset (Simple Offset, NOT equivalent to 3-point calibration)

Only for simple offset adjustment without linearity correction:

Under measurement screen, long press【MODE】over 2 วินาที, current gap value will be set to zero.

บันทึก: Single-point reset only shifts zero offset and cannot correct non-linear error. Never replace 3-point calibration with single-point reset for high-precision inspection.

1. Auxiliary Function: Analog Output Scaling (0～5V corresponding to 0～5mm)

Complete analog scaling after finishing 3-point calibration:

1. Press MODE to enter menu → select ANA (เอาท์พุทแบบอะนาล็อก)
2. Configure parameters:

0mm gap → Output = 0 วี

5mm gap → Output = 5 วี

3. Optional INV: Output voltage decreases as gap increases (enable as required).
4. Advanced Suggestions (Spindle Runout & Vibration Measurement)
5. Averaging filter parameter AVG: Recommended value 16～64 times. Avoid excessive averaging for 40kHz high-speed sampling to prevent peak signal loss.
6. Threshold setting for OUT1/OUT2 comparison outputs: Complete after calibration. Configure HI/LO alarm limits subsequently.
7. 4 memory banks MEM1~MEM4: Store independent calibration parameters for steel, สแตนเลส, aluminum etc. Direct recall during workpiece change, repeated calibration is unnecessary.

ปกเกล้าเจ้าอยู่หัว. รอบการสอบเทียบ & Data Preservation Reminders

1. Calibration parameters are retained after power-off;
2. Re-calibration required under conditions: ambient temperature fluctuation ＞±15℃, sensor position shift caused by vibration, replacement of sensor head or cables;
3. Record fixture positions after calibration for repeat verification.