ABB OA1G10 Auxiliary Contact

الاسم الكامل: ايه بي بي OA1G10 1NO Auxiliary Contact

رقم الجزء: 1SCA022353R4970. Designed for right-hand mounting on ABB OT series disconnectors / load break switches. 1 مفتوح عادة (1لا), early-make contact.

✅ Model Interpretation

OA: الاتصال المساعد وحدة

1: 1 contact set

ز: Right-side mounting

10: NO Normally Open contact (OA1G01 = 1NC Normally Closed)

📋 Core Technical Data

🛠️ Compatible Switch Models

Suitable for ABB OT series load disconnectors: OT16 ~ OT4000, مكتب المدعي العام, OTR, OTL, OTE

Installation note: Right-side mounting, الحد الأقصى 2 OA1G series auxiliary contacts can be fitted. Used to collect ON/OFF status signals of disconnectors for PLC, indicator lights and interlock circuits.

📌 Application Scenarios

Disconnector position feedback in power distribution cabinets, مركز عملائي, صناديق الجمع الكهروضوئية, HVAC pump control cabinets

Safety interlock, cabinet door interlock, status indicator lamps, switch position acquisition for host system

Main power disconnector signal feedback for machinery

🧩 Series Comparison & البدائل

1. OA1G01: 1نورث كارولاينا (مغلق عادة, right mounting)
2. OA7G10: 1لا (مفتوح عادة, left mounting)
3. OA8G01: 1نورث كارولاينا (مغلق عادة, left mounting)

OA1G10AU: delayed version, do not confuse with standard model.

📦 Foreign Trade Information

رمز النظام المنسق: 85389099 (Electrical equipment parts), أصل: Bulgaria / Finland

ABB OA1G10 Auxiliary Contact Installation Manual (Compiled from ABB original document Doc.No.:1SCC390026M0018)

منتج: OA1G10 1NO auxiliary contact, snap-fit right-side mounting for OT series disconnectors, early-make contact; رقم الجزء:1SCA022353R4970

Compatible units: OT16~OT4000, OTP/OTR/OTL/OTE load disconnectors; related series: OA1G01 (right 1NC), OA7G10 (left 1NO), OA8G01 (left 1NC)

1. تحذيرات السلامة
2. Installation must be performed by qualified electricians. Disconnect main power supply of the disconnector and verify zero voltage before work to prevent electric shock and arc burns.
3. Never plug or remove auxiliary contact module under energized condition.
4. Auxiliary contacts are only intended for control / signal circuits (ايه سي-15), not for main power load.
5. بعد التثبيت, manually operate the disconnector several times to verify contact operation logic.
6. نظرة عامة على المنتج

تصنيف الاتصال: 1لا (one normally open set), early-make (auxiliary contact closes in advance before main contacts of disconnector close)

Rated thermal current: Ith=16A; AC230V 6A / AC400V 4A / AC690V 2A

طريقة التركيب: snap-fit, right side of disconnector. الأعلى. 2 OA1G auxiliary contacts can be mounted side by side on one disconnector.

صالة: M3.5 screw, عزم الدوران الموصى به 0.8 نانومتر (7 رطل. في)

كابل: 0.75～2.5 mm² copper conductor, stripping length 8～10 mm

ثالثا. خطوات التثبيت

Precondition: Disconnector set to OFF position (0)

1. Locate mounting slot

Find the auxiliary contact guide rail on the right side of OT disconnector body. Left rail is only for OA7G/OA8G series, OA1G10 cannot be fitted on left side.

2. Snap module into place

Align guiding catches of OA1G10 with right rail, press evenly inward until a clear “انقر” يسمع الصوت, confirming locking. Pull module slightly to confirm secure fixation.

Multiple modules: ما يصل الى 2 وحدات, snap in sequentially side by side on right rail.

3. Wire signal circuit

Strip insulation of control wire by 8–10mm, insert into terminal; tighten M3.5 screw to torque 0.8Nm.

Terminal marking: 1 و 2 are two terminals of NO contact.

ملحوظة: Do not use conductors larger than 2.5mm², poor terminal compression will occur.

4. Function verification

Manually operate disconnector handle:

ON position (أنا): OA1G10 NO contact closes; early-make feature: auxiliary contact conducts before main contacts close

OFF position (0): OA1G10 NO contact opens

Use multimeter continuity test on terminals to confirm correct logic.

5. Secondary protection check

Ensure wires are not pinched, no bare copper exposed on terminals; fit terminal cover of cabinet.

1. إجراء الإزالة
2. Cut off power of secondary signal circuit.
3. Set disconnector to OFF position 0.
4. Use small flat screwdriver to pry side catch of module, pull OA1G10 outward.
5. Loosen terminal screws and remove control wires.
6. Installation Limitations & قواعد الاختيار
7. OA1G10 = Right mounting. Left-side status feedback requires OA7G10.
8. For one OT switch: الأعلى. 2 OA1G on right rail; الأعلى. 2 OA7G/OA8G on left rail.
9. No cross mixing: OA1G (right type) cannot be inserted into left rail. Mismatched mechanical structure may damage module and switch body by force.
10. OA1G10AU is delayed-travel version with different mechanical stroke; cannot directly replace standard OA1G10.
11. التكليف & استكشاف الأخطاء وإصلاحها

سابعا. صيانة & تخزين

1. Periodic inspection: Manually operate switch every 6 شهور, check contact operation and wiring tightness.
2. Storage environment: Clean and dry, temperature -25℃~+70℃, avoid condensation and dust.
3. الحياة الميكانيكية: Matched with OT disconnector, عادي 20000 دورات التشغيل.

ثامنا. Original Document Reference

Original manual title: Installation Instruction Auxiliary contact OA1G01-OA1G10, OA7G10, OA8G01

ABB Document No.: 1SCC390026M0018

Applicable standards: جيجابايت/ت 14048.5, اللجنة الانتخابية المستقلة 60947-5-1

⚠️ Troubleshooting Summary

1. Contact failure: Verify full installation and handle travel; loose module catch is common fault.
2. Unstable signal: Check screw torque, wire size ≤2.5mm²; AC15 category, heavy load not allowed.
3. Selection reminder: OA1G10 is right-mounted only. OA7G10 for left-side feedback.

Key Installation Notes for ABB OA1G10 Auxiliary Contact

OA1G10: Right-mounted, 1NO early-make auxiliary contact for OT disconnectors, Part No.1SCA022353R4970

1. Pre-installation Check Items
2. Mounting side must be correct

OA1G10 only fits right guide rail of OT switch. Left rail only accepts OA7G10/OA8G01. Forced fitting on left side causes unlocked catch, failed plunger actuation or permanent damage.

2. Switch status confirmation

Install / remove only with OT disconnector at OFF position 0, main circuit and secondary signal circuit de-energized and verified. Hot plugging of auxiliary module is forbidden.

3. Check model timing characteristic

OA1G10 is early-make contact: auxiliary contact closes before disconnector main contacts. If interlock logic requires signal output only after main contact closure, this model is not suitable.

4. Quantity limit

الأعلى. 2 OA1G modules (OA1G10 / OA1G01) can be stacked on right rail of one OT switch.

1. Mechanical Installation Details
2. Snap-fit feedback

Align module guiding ribs with right rail, press steadily inward until distinct “انقر” for locking. Pull module lightly after fitting to confirm no loosening.

Stack multiple modules: insert sequentially, keep modules closely fitted without gap.

2. Plunger inspection

بعد التثبيت, inspect black actuating plunger of module. Plunger extends when switch OFF; plunger is pressed in during switch ON to trigger contact switching. Plunger shall not be skewed or stuck.

3. No hammering allowed

Do not strike module with screwdriver or hammer if insertion is difficult. Plastic housing or internal contact spring may break.

ثالثا. Secondary Wiring Details

1. متطلبات الكابل

Copper wire 0.75～2.5mm²; stripping length 8~10mm. Overlong stripped insulation may cause short circuit between adjacent terminals; insufficient stripping leads to poor crimp.

2. تشديد عزم الدوران

M3.5 terminal screw, standard torque 0.8 نانومتر. Low torque → intermittent signal under vibration; excessive torque → thread slipping and terminal base damage.

3. Terminal definition

المحطات 1 و 2 form NO contact, non-polarized passive dry contact. Not for high power load, utilization category AC-15.

Rating reference: AC230V 6A, AC400V 4A, AC690V 2A, for PLC, indicator lamps and interlock control circuits only.

1. التكليف & Verification (شديد الأهمية)
2. Multiple manual operation test

بعد التثبيت, toggle OT switch ON/OFF for at least 3~5 cycles. Measure with multimeter continuity function:

OFF position 0: صالة 1-2 يفتح

ON position I: صالة 1-2 مغلق (early-make: conduction occurs before handle fully reaches ON position)

2. Fault discrimination

No contact switching: mostly incomplete snap-fit, wrong mounting side;

Intermittent conduction: insufficient screw torque, loose copper strands;

Reversed logic: OA1G01 (نورث كارولاينا) mistakenly selected.

1. عملية & Maintenance Restrictions
2. Auxiliary contact cannot be used as main circuit switch, only for position feedback and safety interlock signal.
3. For cabinets under heavy vibration, recheck screw torque and catch condition every 6 شهور.
4. بيئة: الابتعاد عن الغبار, condensation and corrosive gas to prevent contact oxidation and signal drift.
5. إزالة: Power off first, pry side catch gently with flat screwdriver and pull out module. Never pull module by wires.
6. سوء الفهم المشترك

❌ Misunderstanding 1: OA1G10 can be mounted on either side → Not interchangeable, plunger geometry differs

❌ Misunderstanding 2: Auxiliary contact can drive heavy loads such as contactor coils → AC15 duty, limited load capacity

❌ Misunderstanding 3: Conduction occurs only when handle fully ON → Early-make design, conducts in advance, timing must be considered for interlock design

❌ Misunderstanding 4: Unlimited stacking of auxiliary contacts → Max. 2 units on right rail