OMRON CP1W-8ER Pure Output Expansion Module - Contattore,interruttore automatico,sensore,Codificatore,PLC,Convertitore

Wechat: +86-13184948252 Whatsapp: 0086-13811255435 E-mail: kent@bestcontactor.com

Di Contatto |

OMRON CP1W-8ER Pure Output Expansion Module - Contattore,interruttore automatico,sensore,Codificatore,PLC,Convertitore

PLC/

OMRON CP1W-8ER Pure Output Expansion Module

CP1W: Expansion unit for CP1 series 8: 8 points E: Expansion R: Relay normally open (NO) output Type: Pure output expansion module, no input points Core Specifications Number of output points: 8-point relay NO output Rated current per channel: 2 UN (carico resistivo) Output voltage range: AC/DC 4.5~30 V (passive relay contact) On/off delay: ca. ...

  • Dettagli del prodotto

CP1W: Expansion unit for CP1 series

8: 8 punti

E: Espansione

R: Relay normally open (NO) produzione

Tipo: Pure output expansion module, no input points

Specifiche principali

Number of output points: 8-point relay NO output

Rated current per channel: 2 UN (carico resistivo)

Output voltage range: AC/DC 4.5~30 V (passive relay contact)

On/off delay: ca. 15 SM

Consumo energetico: 5 A DC 0.21 UN; 24 A DC 0.13 UN

Dimensioni: W66 × H90 × D50 mm

Peso: ca. 250 G

Certificazioni: CE, UL, CSA

Lifecycle status: Attivo, not discontinued

Compatibile processore Unità

CP1E / CP1H / CP1L (CP1 series PLC); also compatible with legacy CPM1A/CPM2A

Nota: 20-point CP1E CPU does not support expansion. Only 30/40/60-point CPUs can connect CP1W expansion units.

Cross-model Comparison (for selection)

CP1W-8ER: 8-point relay output (passivo, AC/DC universale)

CP1W-8ET: 8-punto di uscita a transistor NPN (Solo 24 V CC)

CP1W-8ED: 8-punto DC24V input module

CP1W-16ER: 16-point relay output

Linee guida per il cablaggio

  1. Two independent common terminals: COM0 (00~03), COM1 (04~07)
  2. Relay is dry contact: connect AC L / DC+ to COM as required, then wire the load to the contact terminal
  3. Non azionare direttamente motori ad alta potenza; add intermediate contactors
  4. Per carichi induttivi (elettrovalvole, bobine), install freewheeling diodes (DC) o ammortizzatori RC (AC) to extend relay life.

Risoluzione dei problemi

No output action:

1) Check if the expansion cable is firmly plugged in and the CPU recognizes the expansion unit

2) Verify the I/O address assignment (expansion I/O follows the previous unit’s address sequentially)

3) Measure COM power supply and check for open circuits in the load loop

Permanent ON for one channel: relay contact welding; replace the point or the whole module

No output on all channels: expansion function disabled, too many expansion units, or damaged cable.

Opzioni di sostituzione

  1. Sostituzione diretta: CP1W-8ER (preferito, no program modification needed)
  2. Transistor alternative: CP1W-8ET (for high-frequency switching and DC loads; cannot handle AC)
  3. Alternativa domestica: CP1-bus compatible 8-point relay expansion module (verify bus protocol and address mapping)

Service Life of CP1W-8ER (Limited by relay contacts)

Official rated life per relay channel

  1. Vita meccanica (funzionamento a vuoto): ≥20 million operations
  2. Vita elettrica (2 Un carico resistivo): ≥100.000 operazioni

Punto chiave: Electrical life is the bottleneck, not the PCB. Carichi induttivi (elettrovalvole, bobine del contattore) drastically shorten service life down to 20,000~50,000 cycles. Snubber circuits will improve this.

Time Estimation (for project evaluation)

1 operation per minute: 100,000 cycles ≈ 19 anni

1 operation per 10 secondi: 100,000 cycles ≈ 2.8 anni

1 operation per second: 100,000 cycles ≈ 27 ore

For equipment with continuous ON state and rare switching: contact wear is minimal. In clean, temperature-controlled cabinets, the PCB, cable and terminals can run stably for 8~15 years. Service life is halved in high-temperature, ambienti umidi e polverosi.

Two Types of Service Life

Contact life: limited by switching cycles; failure symptoms: contact welding or poor contact

Module body life: PCB, cable and drive circuit; aging depends on environmental conditions, no fixed cycle rating.

Life Extension Tips

  1. Add freewheeling diodes (DC) o ammortizzatori RC (AC) for inductive loads such as solenoid valves and contactors.
  2. Keep load current below 1 UN; avoid continuous full-load (2 UN) operazione.
  3. For high-frequency switching (cycles within seconds), use CP1W-8ET transistor output instead of ER relay modules.
  4. Regularly inspect expansion cables and terminals for oxidation and loose connections.

Full List of OMRON CP1W Expansion Units (CP1E / CP1H / CP1L Compatible)

Nota: CP1W units are bus-connected expansion modules (daisy-chained with flat cable). CIF, ADB and DAB boards are CPU side option boards (not bus expansion units). 20-point CP1E cannot use expansion units; only 30/40/60-point CP1E, CP1H and CP1L-M support CP1W expansion.

  1. Digital Input Only Units
ModelloDescrizione
CP1W-8ED8-punto di ingresso DC24V (NPN/PNP universale)
  1. Digital Output Only Units (CP1W-8ER listed here)
ModelloDescrizione
CP1W-8ER8-point relay NO output, 2 UN
CP1W-8ET8-point NPN (affondando) uscita a transistor, 0.3 UN
CP1W-8ET18-point PNP (approvvigionamento) uscita a transistor, 0.3 UN
CP1W-16ER16-point relay NO output, 2 UN
CP1W-16ET16-punto di uscita a transistor NPN, 0.3 UN
CP1W-16ET116-point PNP transistor output, 0.3 UN
CP1W-32ER32-point relay NO output, 2 UN
CP1W-32ET32-punto di uscita a transistor NPN, 0.3 UN
CP1W-32ET132-point PNP transistor output, 0.3 UN
  1. Unità I/O miste (Ingresso + Output integrated)
ModelloDescrizione
CP1W-20EDR112 DC inputs + 8 uscite relè
CP1W-20EDT12 DC inputs + 8 NPN transistor outputs
CP1W-20EDT112 DC inputs + 8 PNP transistor outputs
CP1W-40EDR24 DC inputs + 16 uscite relè
CP1W-40EDT24 DC inputs + 16 NPN transistor outputs
CP1W-40EDT124 DC inputs + 16 PNP transistor outputs
  1. Analog I/O Units (Voltaggio / Segnale corrente)
ModelloDescrizione
CP1W-AD0414 AI, risoluzione 1/6000; tensione/corrente selezionabile
CP1W-AD0424 AI, alta risoluzione 1/12000
CP1W-DA0212 AL, risoluzione 1/6000
CP1W-DA0414 AL, risoluzione 1/6000
CP1W-DA0424 AL, alta risoluzione 1/12000
CP1W-MAD112 AI + 1 AL, risoluzione 1/6000
CP1W-MAD424 AI + 2 AL, alta risoluzione 1/12000 (più popolare)
  1. Temperature Input Units (Termocoppia / Pt RTD)
ModelloDescrizione
CP1W-TS0012-channel thermocouple (K/J type)
CP1W-TS0022-channel Pt100/Pt1000 RTD
CP1W-TS0032-channel multi-function: termocoppia / RST / ingresso analogico
CP1W-TS00412-channel thermocouple (for oven & injection molding multi-point temperature monitoring)
  1. Accessori (Cavo di espansione)
ModelloDescrizione
CP1W-CN81180 cm extension cable; short cable (6 cm) included with each module

Supplementare: CPU Side Option Boards (NOT Bus Expansion Units)

These plug directly into the CPU side slot and cannot be daisy-chained on the I/O bus:

CP1W-CIF01: RS232C

CP1W-CIF11: Non-isolated RS422/485

CP1W-CIF12 / CIF12-V1: Opto-isolated RS422/485

CP1W-CIF41: Ethernet option board

CP1W-DAM01: LCD display panel

CP1W-ADB21 / DAB21V / MAB221: Small analog option boards

Guida alla selezione rapida

  1. Commutazione ad alta frequenza, elettrovalvole, servo pulse output → Choose ET / ET1 transistor models, do not use ER relay modules
  2. AC220V loads with infrequent switching → Select ER relay models
  3. Thermocouple temperature measurement: TS001; Pt RTD: TS002; multi-point temperature monitoring: TS004
  4. I/O analogico: MAD42 (4-in 2-out) è preferito; new projects select high-resolution AD042 / DA042

 

Prec:

Prossimo:

Lascia una risposta

Lasciate un messaggio