Siemens 6EP1437-2BA10 Industrial Power Supply

Siemens 6EP1437-2BA10 SITOP POWER 40 Trifase Industrial Power Supply

1. Scomposizione del codice modello

6EP1437-2BA10

6EP: Standard industrial power supply series of SITOP

1437: High-power three-phase AC model, 40A output platform

2: Basic standard version (without redundant diagnostic interface)

BA: Montaggio su guida DIN, 24Uscita VCC

10: 3-phase 400–500V input, 40UN / 960W output specification

1. Parametri elettrici principali

Lato ingresso (3-Phase Industrial Grid)

Input format: 3×400～500V AC, 3-phase 5-wire L1/L2/L3/PE

Frequenza: 50/60Hz

Voltage dip tolerance: Minimum 340V for 2 seconds without output collapse

Wire gauge for input terminals: 0.5～4mm² solid/stranded copper wire

Output Side (Standard Industrial 24VDC)

Potenza nominale: 24VCC / 40UN, total power 960W

Adjustable output voltage range: 22.8～26.4V (tweaked via potentiometer at bottom)

Ripple & rumore: Ripple ＜150mVpp, peak noise ＜240mVpp

Output terminals: Dual groups of +/terminals for parallel connection; wire gauge 0.5～10mm²

Parallel expansion: Two identical units can be directly paralleled for max. 80Un'uscita

Funzioni di protezione (Full-condition Protection)

1. Protezione da cortocircuito: Automatic hiccup current limiting, auto-recovery after fault clearance
2. Protezione da sovratensione (OVP): Output cut-off when voltage ＞27V
3. Protezione da sovraccarico (OLP): Current limiting at 120% corrente nominale
4. Over-temperature Protection (OTP): Shutdown on overheat, auto-restart after cooling down
5. Protection against input phase loss, surge and industrial EMC interference

III. Meccanico & Specifiche ambientali

Montaggio: Vertical installation on standard 35mm DIN rail

Dimensioni complessive (L × A × P): 160 × 125 × 121 mm

Peso netto: ca. 2.0 kg

Classe di protezione: IP20 (for cabinet installation only)

Temperatura operativa: 0～+55°C (full power derating required above 55°C)

Magazzinaggio / transport temperature: -25℃～+85℃

Umidità: 5%～95%RH, nessuna condensa

Certificazioni: CE, UL, GL marine certification; compliant with EN61010, EN61000 industrial EMC standards

1. Comparison Table of Same-Series 3-Phase Power Supplies

1. Definizione del terminale
2. Input terminals: L1, L2, L3, PE (3 fasi + protective earth)
3. Output terminals: Dual sets of +24V, 0V (parallel for current sharing)
4. Voltage trimming potentiometer: Located at bottom; adjust with flat screwdriver
5. Indicatore luminoso: Solid green = normal output; spento / flashing = fault (perdita di fase, cortocircuito, surriscaldamento)
6. Scenari applicativi tipici
7. Large PLC control cabinets (S7-1500/400, full-station power supply for ET200SP distributed I/O)
8. Multi-axis servo systems, inverter control stations, postazioni di lavoro robotizzate
9. Confezione, logistics sorting, automotive welding & assembly production lines
10. Trattamento dell'acqua, energia eolica, metallurgia, cement and other high-power industrial control equipment
11. Centralized 24V power supply scenarios requiring 3-phase industrial incoming power and high current loads

VII. Sostituzione & Capacity Expansion Solutions

1. Upgraded same-spec model: 6EP1437-3BA00 (with fault relay contacts for PLC diagnostic connection)
2. Capacity expansion: Parallel two 6EP1437-2BA10 units for max. 80UN / 1920W output
3. Downsized alternative: 6EP1436-2BA10 (20UN / 480W) for half-load applications

VIII. Installation Prohibitions & Guida alla risoluzione dei problemi

Forbidden Operations (Critical Restrictions)

1. Horizontal or upside-down mounting is strictly prohibited; blocked cooling air duct triggers rapid over-temperature protection
2. Long-term power-on with direct output short circuit will cause continuous hiccup power derating
3. Long-term operation with missing input phase accelerates aging of internal power components
4. Do not install alongside high-power inverters without partition plates to avoid EMC interference

Common Fault Matrix

Official Overall Dimensions of Siemens 6EP1437-2BA10 (SITOP POWER 40 3-Phase 40A Power Supply)

1. Overall Unit Dimensions (L × A × P, unità: mm)

160 × 125 × 121 mm

Larghezza (horizontal along DIN rail): 160 mm

Altezza (vertical cooling air flow direction): 125 mm

Profondità (cabinet depth direction): 121 mm

Peso netto: ca. 2.0 kg

2. Dimension Differentiation of Confusable Same-Series Models (Avoid Errors in Procurement & Cabinet Layout)

3. Cabinet Installation Clearance Requirements
4. Binario di montaggio: Standard 35mm TH35 DIN rail, installazione verticale (terminals downward)
5. Superiore & bottom ventilation clearance: Reserve at least 40mm for heat dissipation; derating mandatory if ambient temp exceeds 55℃
6. Side-by-side mounting: Units of same model can be tightly arranged without extra spacing

Nota integrativa

Dimensions such as 250×180×92 and 145×145×150 shown on some foreign websites belong to the new PSU300S model 6EP1437-2BA20, which is incompatible with the legacy 6EP1437-2BA10. Cabinet cutout and DIN rail layout cannot be shared between them.