ABB ACS350-03E-23A1-4 Micro Drive

(Full model number; サフィックス 4 = 380~480V three-phase)

状態: The ACS350 series is discontinued. No new production from ABB; only surplus stock and second-hand units are available as spare parts.

Product positioning: General-purpose OEM micro drive, widely used on machine tools, コンベア, fans and pumps for legacy equipment.

✅ Model Code Breakdown

ACS350: 製品シリーズ, legacy general machinery drive

03: Three-phase input power supply

E: EMCフィルター内蔵 (50Hz version)

23A1: 定格出力電流 23.1 あ

4: 電圧クラス, 380~480V three-phase

✅ Key Technical Specifications

定格電力: 11 kW (15 HP)

Rated output current I2N: 23.1 あ

Input supply: 3-phase 380–480 V, 48~63 Hz

出力: 0~input voltage, 0~500 Hz

過負荷容量: 150% I2N for 60 seconds per 10 分; 180% I2N for 2 seconds at startup

フレームサイズ: R3

保護クラス: IP20

Standard feature: Built-in braking chopper

スイッチング周波数: デフォルト 4 kHz; selectable 4/8/12/16 kHz

Control modes: V/F scalar control, sensorless vector control for asynchronous motors; native Modbus RTU; optional fieldbus adapters

キーパッド: ACS-CP-A / ACS-CP-C (interchangeable with ACS355)

周囲条件: No derating from -10℃ to +40℃; 10% power derating at 50℃; ≤1000 m altitude; 1% derating per 100 メートル上 1000 メートル.

✅ Direct Replacement Models (Field Retrofit Priority)

1. Pin-to-pin compatible replacement: ACS355-03E-23A1-4 (11 kW, 23.1 あ, Frame R3)

同一の端子配置, macros and keypad; direct swap for most installations with minor parameter adjustments. The ACS355 is also phased out with dwindling stock.

2. Long-term new-generation upgrade: ACS380-04S-026A-4 (11 kW, 26 あ)

Similar IO logic; equipped with STO (安全トルクオフ); 安定供給. Requires rechecking wiring, application macros and communication parameters.

✅ Spare Parts List

キーパッド: ACS-CP-A (Assistant Panel, 推奨) / ACS-CP-C (Basic Panel)

制動抵抗器: Select according to deceleration duty; braking chopper is built-in, external resistor required

Fieldbus adapters: FDNA-01 (デバイスネット), FPBA-01 (プロフィバスDP), FENA-01 (イーサネット)

EMC note: E-type includes integrated EMC filter; U-type has no built-in filter.

✅ 一般的な用途

ベルトコンベア, 包装機械, woodworking equipment, ファン, ウォーターポンプ, small machine tool spindles and general constant-torque loads.

✅ Common Fault Troubleshooting (ACS350 Series Common Issues)

1. 過電流: モーターの短絡, damaged power cable, 機械的な妨害, too short acceleration time, failed IGBT module
2. 過電圧: Excessively fast deceleration, missing or mismatched braking resistor, 高い主電源電圧
3. 地絡: Breakdown of motor insulation, leakage to ground on output cables
4. Modbus communication loss: Check terminating resistor, A/B polarity, station address and baud rate
5. No keypad display: 24V control supply failure, faulty control board or power board

✅ Supplementary Notes

Parameters cannot be copied directly between ACS350 and ACS355; parameter files must be re-uploaded/downloaded. Although the keypad is interchangeable, firmware and parameter groups differ. Always compare the original parameter list during replacement.

ABB ACS350-03E-23A1-4 (11 kW) Engineering Application Cases

説明: The ACS350 is a legacy OEM machinery drive with built-in EMC filter, 統合されたブレーキチョッパー, embedded sequence programming and native Modbus RTU, ideal for constant-torque loads. Below are the most common field applications for this power rating, including process description, control scheme, key parameters, risk points and retrofit notes.

場合 1: Main Belt Conveyor on Packaging Lines (Classic Constant-Torque Application)

負荷: 11 kW conveyor motor for bulk material handling; smooth start/stop, anti-jam and speed synchronization between upstream/downstream sections required.

Control Scheme

制御モード: センサレスベクトル制御 (99.04=1)

速度基準: AI1 receives potentiometer/PLC analog signal; digital inputs select multi-speed preset (feed, normal speed, low-speed material clearing)

インターロック: Photoelectric jam signal from downstream fed into DI for automatic speed reduction; emergency stop wired to drive safety circuit

制動: Built-in chopper + external braking resistor for fast stopping to prevent material pile-up

Key Parameter Settings

Acceleration: 8 s; Deceleration: 6 s; stall protection enabled

アプリケーションマクロ: Factory default macro; use embedded sequence programming to reduce PLC I/O count

Field Benefits: High low-speed torque without belt slip; lower mechanical shock and belt wear compared with star-delta starters. This is a widely used legacy application; preferred replacement part is ACS355-03E-23A1-4.

リスク: Regular dust cleaning required for dusty environments; overvoltage alarms occur if deceleration is too fast.

場合 2: Woodworking Machinery – Sanding Machine Feed Roller Drive

負荷: Feed roller of sanding equipment; fluctuating load, stable low-speed torque without speed fluctuation to avoid sanding marks on workpieces.

Control Scheme

ベクトル制御; DI run command; AI speed signal from main machine controller

Multi-speed selection for different workpiece thicknesses (low speed for thick boards, high speed for thin boards)

150% / 60 s overload protection to handle board jamming

Environmental Features: Cabinet-mounted IP20 unit for dusty woodworking workshops; built-in EMC filter on E-version prevents interference with proximity switches and encoders.

制限: No STO safety function. Upgrade to ACS380 for new machine retrofits.

場合 3: Screw Lifts / Bucket Elevators in Food Production Lines

負荷: 11 kW vertical material handling with potential energy load; anti-rollback on shutdown.

Control Scheme

Standard built-in braking chopper with external resistor to prevent load coasting downhill

Digital terminal start/stop; 4–20 mA analog speed control; Modbus RTU communication with PLC host

Level interlock: Automatic speed reduction on low material level, auto-stop on full bin

Process Notes: Waterproof control cabinet for humid conditions; strict earthing and high motor insulation resistance required.

述べる: The ACS350 was ABB’s flagship OEM drive for bakery, extrusion and feed processing lines.

場合 4: Extruder Auxiliary Traction Drive (Plastics Industry)

負荷: Traction roller on plastic extrusion lines; constant torque with speed proportional synchronization with main extruder.

Control Scheme

オプション 1: AI speed follow signal from main drive (proportional speed regulation)

オプション 2: Modbus RTU bus synchronization with master drive

Vector control maintains stable tension at low speed to avoid breakage or material accumulation

Embedded sequence programming for start delay and stop sequence to simplify PLC logic

比較: Main extruders typically use ACS510/ACS550 while ACS350 serves as a cost-effective auxiliary drive. Re-synchronization logic is required when retrofitting to ACS380.

場合 5: 空調設備 & Water Treatment Circulation Pumps (可変トルク, PID Closed Loop)

負荷: 11 kW cooling water circulation pump or constant-pressure water supply pump.

Control Scheme

制御モード: V/F scalar control; built-in PID macro; 4–20 mA pressure transmitter feedback to AI2

Goal: Maintain constant pipe pressure with variable speed energy saving

One-duty-one-standby rotation must be implemented via external PLC; the ACS350 does NOT support built-in PFC pump cycling function (difference from ACS510)

省エネ: 20%~40% power reduction under partial load compared with direct-on-line operation.

場合 6: Small CNC Machine Tools – Spindle Cooling & Conveyor Drives

負荷: Machine tool feed rollers, cooling fans and chip conveyors with 11 kW rating.

Control Scheme

Keypad/terminal control with multi-speed preset linked to CNC M-codes; FPBA-01 Profibus DP adapter for CNC system networking

EMC compliance guaranteed by integrated EMC filter on E-version

制限: Only for asynchronous motors; not compatible with permanent magnet synchronous motors. No longer specified for new machine builds.

場合 7: Roller Feeders for Sand & Building Material Auxiliary Lines

負荷: Roller feeders and apron feeders with frequent start-stop and shock loading.

Control Scheme

Vector control to boost starting torque; stall protection triggers alarm on material jamming

Modbus RTU remote control via central PLC; real-time current and fault code monitoring

環境: Installed in standalone ventilated cabinets for heavy dust conditions; regularly test output cable insulation to prevent earth faults.

General Commissioning & Retrofit Summary (ACS350-03E-23A1-4)

1. Constant-torque loads (コンベア, 木工, traction, エレベーター): Use sensorless vector control and take full advantage of the built-in braking chopper.
2. Variable-torque loads (ファン & パンプス): Use V/F scalar control + 内蔵PID. Note that PFC pump rotation is not supported on ACS350 and requires external PLC logic.
3. コミュニケーション: Native Modbus RTU; optional extensions: プロフィバスDP (FPBA-01), デバイスネット (FDNA-01).
4. Spare Part Replacement

Direct like-for-like swap: ACS355-03E-23A1-4 (identical terminals & キーパッド; no direct program copy due to parameter group differences)

長期的なアップグレード: ACS380-04S-026A-4 (STO equipped; IO and communication logic must be re-engineered)

5. Shortcomings: No STO safety torque-off function; fully discontinued with only surplus and second-hand stock available.
6. Model Prefix Code Definition

01: Single-phase input 200–240 V

03: 三相入力

E: EMCフィルター内蔵 (this model = 03E); U: No built-in filter; ×: Placeholder for E/U in selection codes

サフィックス 2 = 200–240 V; サフィックス 4 = 380–480 V (this model suffix = 4)

パワーレンジ: 0.37 kW〜 22 kW, frame sizes R0/R1/R2/R3/R4

1. 三相 380 ～ 480 V (03E-xxx-4 Series, Primary Model Range)

ACS350-03E-XXAXX-4 (with built-in EMC filter)

Filter-free version: Replace 03E with 03U; power and current ratings remain identical.

Ⅲ. Three-phase 200–240 V (03E-xxx-2)

1. Single-phase 200–240 V (01E-xxx-2, Single-phase Supply)

Filter-free version: Change 01E to 01U.

1. Cross-Model Replacement List (Spare Part Retrofit)
2. Direct pin-compatible replacement: ACS355-03E-23A1-4 (11 kW, 23.1 あ, R3)

Same terminal layout and keypad; minor parameter tuning only. The ACS355 is also discontinued with limited stock.

2. New-generation long-term upgrade: ACS380-04S-026A-4 (11 kW, 26 あ)

Equipped with STO Safe Torque Off; 安定供給; requires rework on wiring, macros and communication settings.

1. Supplementary Remarks
2. 全モデル: IP20保護, 内蔵ブレーキチョッパー, native Modbus RTU included as standard.
3. Code definitions: E = Built-in EMC Filter; U = No EMC Filter; X = E/U selection placeholder.
4. The entire ACS350 series is officially end-of-life; only surplus stock and second-hand spare parts are available.
5. Original ABB order codes can be retrieved upon model number request.