접촉기,회로 차단기,태양광 인버터,전기 계량기,태양 전지
모델 코드 해석
E82EV551_4C
E82EV：8200 Vector series frequency inverter
551：Power code → 0.55 kW
4：3-phase input 380…480 V AC
기음：Standard hardware version
- 주요 전기 사양
| 목 | 사양 |
| 정격 출력 | 0.55 kW |
| 입력 전압 | 3-phase 380～480 V AC ±10% |
| 입력 주파수 | 50 / 60 헤르츠 |
| 정격 입력 전류 | 1.8 에이 |
| 정격 출력 전류 | 1.6 에이 |
| 출력 주파수 | 0～480 Hz |
| 제어 모드 | V/F 제어, 센서리스 벡터 제어 |
| 냉각방식 | Natural air cooling (no built-in fan) |
- 하드웨어 & 인터페이스
- Standard Interfaces
RS232 (렌츠 diagnosis port for X500 commissioning)
Digital inputs/outputs, analog inputs/outputs (0-10V / 4-20mA)
Relay fault output
- Optional Communication Modules (slot extension)
프로피버스-DP, CANopen, 모드버스, 디바이스넷, 등.
Module examples: E82ZAFPC001 (프로피버스), E82ZAFCC001 (CANopen)
- 환경 사양
작동 온도: 0～+45℃ (경감 없음); 최대. 55℃ with current derating
보호 등급: IP20 (cabinet mounting)
보관온도: -20～+70℃
고도: ≤1000 m without derating; current derating required above 1000 중
- 치수 & 설치
설치: DIN 레일 장착 / 나사 고정
Form factor: Compact book-style
Larger models in the same series: E82EV751_4C(0.75kW), E82EV152_4C(1.5kW)
- Commissioning Software
소프트웨어: Lenze EASY Starter
Commissioning cable: X500 dedicated cable (E82ZBC)
- 교체 정보 (중요한)
E82EV series is Obsolete / 단종
✅ Official upgrade series: i500 frequency inverter
Recommended equivalent model: I5AE055A1000 (0.55 kW, 380 V 클래스)
⚠️ Notes:
- Terminal definition and parameter codes are incompatible with 8200; parameters must be re-commissioned.
- Communication modules cannot be directly interchanged.
- Mounting dimensions differ slightly; cabinet modification may be required.
- 일반적인 응용 분야
소형 컨베이어, 팬, 슬리퍼, compact packaging machinery, 벨트 컨베이어, simple spindle drives.
- General Operation Notes
- This model has no integrated brake transistor. An external brake unit must be used if brake resistors are required.
- An output reactor is recommended for long motor cables to suppress dv/dt and protect motor insulation.
- Factory default mode: V/F 제어. Activate vector control via parameters if required.
Available supporting documents upon request:
Complete terminal wiring diagram
Factory default parameter list
i500 alternative parameter comparison table
Fault code list
LENZE 8200 Vector Fault Code List (Applicable to E82EV Series including E82EV551_4C)
Display code | Internal No. | Fault Name | 원인 & 문제 해결
Distinguish TRIP faults (locked shutdown) and Warnings (지속적인 작동)
- Current-Related Faults (가장 일반적인)
| Display Code | Internal No. | Fault Name | 원인 & 문제 해결 |
| OC1 | 11 | Hardware Short-Circuit Fault (Hardware Overcurrent) | Inter-phase short circuit in motor cable, shorted motor winding, output earth short circuit; damaged IGBT |
| 문제 해결: Power on with motor disconnected. If OC1 still occurs → inverter hardware failure; if fault disappears → motor/cable fault | |||
| OC2 | 12 | 지구 결함 (Leakage to Ground) | Damaged motor cable contacting ground, breakdown of motor winding insulation; long cables without output reactor |
| OC3 | 13 | Overcurrent during Acceleration | 갑작스러운 부하 변화, mechanical seizure, too short acceleration time, incorrect motor parameters |
| OC4 | 14 | Overcurrent during Deceleration | Insufficient deceleration time, high inertia load; DC bus fluctuation triggering overcurrent without brake resistor |
| OC5 | 15 | Overcurrent at Constant Speed | Heavy load fluctuation, seized bearing, 모터 위상 손실, failed motor identification for vector control |
| OC6 | 16 | Motor I²t Overload | Prolonged heavy load, motor thermal overload; mismatched power rating |
| LP1 | 32 / 182 | Motor Phase Loss Detection (Active when C0597 enabled) | 느슨한 배선, open circuit of one motor phase; false alarm possible for low-power drives under no-load |
| 문제 해결: 터미널을 조이세요; adjust threshold C0599 |
- DC Bus Voltage Faults
| Display Code | Internal No. | Fault Name | 원인 & 문제 해결 |
| 루 | — | DC 버스 저전압 | Low 3-phase supply voltage, input phase loss, poor contactors, voltage drop during power-up |
| ⚠️ E82EV551_4C has no built-in input fuse; prioritize checking upstream circuit breakers and terminals | |||
| OU | — | DC 버스 과전압 | Rapid deceleration, regenerative energy from high inertia loads; excessive mains voltage; missing brake resistor |
| This model has no integrated brake transistor. An external brake unit + resistor is mandatory for frequent start-stop operation |
III. Overtemperature Faults
| Display Code | Internal No. | Fault Name | 원인 & 문제 해결 |
| 오 | 50 | Inverter Heatsink Overtemperature | Poor cabinet ventilation, 주변 온도 >45℃; dust blocking cooling channels |
| E82EV551_4C adopts natural cooling without fan, highly dependent on ambient cooling conditions | |||
| OH3 | 53 | PTC Motor Overtemperature Trip | Overheated motor PTC thermistor; open/short-circuited PTC wiring; temperature monitoring enabled via C0119 |
| OH51 | 203 | PTC Overtemperature Pre-Warning | Motor temperature approaching protection threshold, advance warning |
| FAn1 | 95 | Fan Fault (Not applicable to this model! E82EV551 has no fan, this code will not appear) | Only applicable to higher-power models equipped with cooling fans |
- Communication Bus Faults (Only with optional communication modules)
| Display Code | Internal No. | Fault Name | 원인 & 문제 해결 |
| Ce0 | 60 | LECOM Communication Fault (X500 diagnostic port) | Loose commissioning cable, damaged E82ZBC cable |
| Ce1 | 61 | CAN-IN1 Communication Fault | Faulty CANopen wiring, missing termination resistor, incorrect node address |
| Ce2 | 62 | CAN-IN2 Synchronous Communication Fault | Loss of bus synchronization signal |
| Ce5 | 65 | BUS-OFF Status | Severe bus interference or short circuit; drive automatically disconnects from bus |
| 행동: Check shield grounding, 120惟 termination resistor and bus polarity | |||
| Ce6 | 66 | CAN Bus Timeout | No response from master station; communication monitoring time C0126 set too short |
- 매개변수 & Internal Hardware Faults
| Display Code | Internal No. | Fault Name | 원인 & 문제 해결 |
| CCr | 71 | Controller Internal Fault | 심각한 전자기 간섭, main control hardware damage |
| 시험: Restore factory settings first; replace drive if fault persists | |||
| Pr0 | 75 | Damaged Parameter Set 0 | Parameter modified during power-off, EEPROM abnormality; restore factory settings C0002=10 |
| Pr1～Pr5 | 76～80 | Damaged Parameter Set 1~5 | Corrupted parameter bank; re-download parameters or perform factory reset |
| id1 | 140 | Invalid Motor Identification Data | Motor identification interrupted, motor disconnected; re-run motor identification C0148 |
| H05 | 105 | Hardware Detection Fault | Self-test failure of power board / 구동 회로; hardware damage |
- External Control Status & 결함
| Display Code | Fault Name | 설명 |
| EEr | External Fault (Triggered via digital input) | External emergency stop or external fault terminal activated; check X3 external fault signal |
| QSP | Quick Stop Active | Quick stop terminal enabled; status message, NOT a trip fault |
| inh | Controller Inhibit | Enable condition not satisfied; no trip, drive cannot start |
Important Practical Tips for E82EV551_4C
- Distinguish status vs fault: inh, QSP, DCB are operating statuses, not trip faults and do not require reset. OC/LU/OH/CCr are trip faults requiring manual reset.
- Fault reset methods: RESET key on panel, bus command reset, power cycle.
- Fault history storage: Parameter C0084 Latest Fault, C0087 Previous Fault, C0088 Second Previous Fault for historical fault review.
- No-load test method: Disconnect motor cables and power on, to judge whether the fault originates from the inverter itself or external wiring/motor.
- This model has no built-in brake transistor. If OU overvoltage frequently occurs during deceleration, external brake unit is required.
