EATON EMT6-KDB Motor Protection Relay

(Comanda nr.: 269471)

Tip de produs: Thermistor (PTC) Releu protectie motor, Ex Explosion-proof, Dual Sensor Circuit

Eaton Moeller EMT6 series for PTC thermistor temperature monitoring of motor windings.

K = ATEX explosion-proof certification; DB = Dual sensor input circuit

✅ Model Code Explanation

EMT6: Serie, PTC thermistor motor protection relay

K: ATEX certified, suitable for Ex e explosion-proof motor applications

DB: Two independent PTC sensor input circuits (simultaneously monitor 2 temperature points, de ex. stator + bearing, or pre-alarm + excursie)

Cod de comandă: 269471

✅ Key Features

Dual PTC circuit monitoring, two sensor channels evaluated independently to support pre-warning and protection logic
Sensor wire break and short-circuit detection (unique to K variants: detects not only wire breakage but also short circuits of sensor cables)
Zero-voltage safety protection (undervoltage lockout): the relay will not auto-reset after tripping due to power loss; configurable via DIP switch
Resettable modes: local manual reset / remote reset
Front panel Test/Reset button for commissioning to simulate over-temperature faults
Status LEDs: power indication, indicarea defecțiunii
SIL 1 nivelul de siguranta (UNUL TĂU 50495), suitable for temperature protection of explosion-proof equipment

✅ Electrical Specifications

Tensiune de alimentare: 24～240V AC/DC wide range

Contact auxiliar: 1NU + 1NC (contact de schimbare), rated thermal current 6A

Tip senzor: PTC thermistor (130℃ / 150℃ PTC embedded in motor windings)

Pragurile: Over-temperature trip >1330Oh; reset <550Oh; sensor short-circuit fault <50Oh

Montare: DIN rail snap-on mounting, width 22.5mm

Terminale: Borne cu șuruburi, tightening torque 1.2Nm

Protecția carcasei: IP20 (numai pentru instalarea dulapului)

Temperatura mediului ambiant: Operating -25℃ ~ +60℃ (max. +45℃ for tightly sealed cabinets)

Standarde: IEC/EN 60947-8, ATEX, CE, UL, Certificare CCC

✅ Aplicații

Winding temperature protection for Ex-e increased safety explosion-proof motors (primary use case for K models)

Temperature protection for motors, gearboxes, pumps and fans via PTC thermistors

Dual-point temperature monitoring: de ex. one channel for winding over-temperature trip, one channel for bearing pre-alarm

Thermal protection for equipment in chemical, farmaceutic, coal and other explosion hazardous areas

✅ Comparison of Related Series Models

Model	Comanda nr.	Nu. of Circuits
EMT6-K	269470	Singur
EMT6-KDB	269471	Dual
EMT6-DB	66167	Dual
EMT6-DBK	66168	Dual

✅ Troubleshooting Guide

No LED on power-up: Check supply voltage 24~240V AC/DC
Fault LED steady ON:

PTC over-temperature (rezistenţă >1330Oh)

Sensor circuit wire break

Sensor cable short-circuit (KDB exclusive detection function)

Cannot reset after trip: Zero-voltage lockout is activated; power cycle or disable undervoltage lockout via DIP switch
Funcția de testare: Press front Test button to simulate over-temperature and trigger relay trip

✅ Alternative Selection Reference

Same brand alternative: EMT6-DBK (without ATEX explosion-proof certificate, other functions similar)

Alternativă internă: Domestic dual-channel PTC motor protection relay (nota: for explosion-proof applications, domestic alternative must provide valid ATEX certificate for direct replacement of EMT6-KDB)

EATON EMT6-KDB Ambient Temperature Specifications

Open ventilated cabinet operating ambient temperature: -25℃ ～ +60℃
Sealed cabinet installation (slabă disipare a căldurii): -25℃ ～ +45℃ (reduced upper limit)
Temperatura de depozitare: -45℃ ～ +85℃

Note suplimentare:

Under UL/CSA certified operating conditions, the nominal rated ambient temperature on nameplate is 40℃

For ATEX explosion-proof applications, ATEX code ambient limits must be followed, not solely the 60℃ upper limit

EATON EMT6 Full Series Model List (PTC Thermistor Motor Protection Relay)

Abbreviation Definition

K: ATEX explosion-proof certified, supports sensor cable short-circuit detection

DB: Dual PTC sensor circuit

EMT62: Dual normally open contact version

(230V): Fixed 230V AC supply; no suffix = wide voltage 24~240V AC/DC

Model	Comanda nr.	Sensor Circuits	Alimentare electrică	Descriere
EMT6	66166	Singur	24~240V AC/DC	Model de bază, no short-circuit detection, nerezistent la explozie
EMT6(230V)	66400	Singur	230V și	Single circuit, fixed 230V power supply
EMT6-DB	66167	Dual	24~240V AC/DC	Dual circuit, no short-circuit detection, nerezistent la explozie
EMT6-DB(230V)	66401	Dual	230V și	Dual circuit, fixed 230V power supply
EMT6-DBK	66168	Dual	24~240V AC/DC	Dual circuit with sensor short-circuit detection, fara ATEX
EMT6-K	269470	Singur	24~240V AC/DC	Single circuit, ATEX certified, with short-circuit detection
EMT6-KDB	269471	Dual	24~240V AC/DC	Dual circuit + ATEX + short-circuit detection (target model)
EMT62	171889	Singur	24~240V AC/DC	Single circuit, dual NO output contacts
EMT62-DB	171890	Dual	24~240V AC/DC	Dual circuit, dual NO output contacts

Ghid de selecție rapidă

Zona cu pericol de explozie (Ex-e motor) → EMT6-K / EMT6-KDB
Industria generală, require sensor cable short-circuit detection → EMT6-DBK
Industria generală, dual temperature monitoring, short-circuit detection not required → EMT6-DB
Two independent normally open alarm outputs required → EMT62 / EMT62-DB

EATON EMT6-KDB (Order No.269471) Dimensiuni fizice

Montat pe șină DIN; housing dimensions identical across all EMT6 variants

Lăţime(W): 22.5 mm (nominal 23mm, standard 22.5mm DIN rail module width)

Înălţime(H): 83 mm

Adâncime(D): 103 mm (measured from DIN rail mounting surface to front face)

✅ Weight: 0.13 kg approx.

Observații: