Преобразователь частоты ABB ACS580-01-087A-4

The ACS580-01-087A-4 is a standard wall-mounted single drive unit from АББ’s ACS580 series, рассчитан на трехфазный вход переменного тока 380–480 В.. Эта серия приводов отличается удобным управлением., высокая надежность и превосходная энергоэффективность как основные преимущества. Multiple standard built-in functions eliminate the need for extra optional components, enabling rapid commissioning and deployment. Widely compatible with general industrial loads such as pumps, фанаты, conveyors and mixers, it is the preferred solution for light industry, building HVAC, water treatment and other applications.

Breakdown of Model Code

Per ABB official naming convention, each segment of the model designation is defined as follows:

ACS580: Идентификатор серии продукта, representing ABB’s general-purpose standard drive series covering power ratings from 0.75kW to 500kW

-01: Construction type, standing for wall-mounted standard single drive. Standard equipment includes IP21 enclosure rating, Assistant Control Panel, built-in Class C2 EMC filter, Безопасное отключение крутящего момента (СТО), braking chopper and triple-protection coated circuit boards

-087А: Rated output current marking, indicating the nominal rated output current of the drive is 87A

-4: Класс напряжения, denoting three-phase 380V–480V AC input, compatible with 50/60Hz mains power grids

Основные технические характеристики

Electrical Ratings

Параметр	Спецификация	Примечания
Диапазон входного напряжения	3-phase AC 380V ~ 480V	Tolerance: +10% / -15%
Input Frequency	50/60Гц	Tolerance: ±5%
Номинальный выходной ток	87А	Nominal value for light-duty applications
Соответствующая мощность двигателя (Light Duty)	45кВт	For variable-torque loads (фанаты, водяные насосы)
Соответствующая мощность двигателя (Сверхмощный)	37кВт	For constant-torque loads (транспортировка, mixing)
Диапазон выходной частоты	0 ~ 500Hz	Supports high-speed motor operation
Input Power Factor	≥0.98	High power factor across full power range
Overall Efficiency	≥98%	At rated operating conditions
Перегрузочная способность	150% номинальный ток в течение 60 с	One overload cycle permitted every 10 минуты
Перегрузочная способность	110% rated current continuously	One overload cycle permitted every 10 минуты

Контроль & Interface Specifications

Motor Control Modes: Scalar V/F control, бездатчиковое векторное управление; compatible with induction motors, permanent magnet synchronous motors and synchronous reluctance motors

Физические размеры & Environmental Specifications

Размер кадра: R5

Габаритные размеры (H × W × D): 896mm × 345mm × 293mm

Net Weight: Приблизительно. 23кг

Enclosure Rating: IP21 (стандартный); IP55 high-protection version available as option

Тип монтажа: Wall mounting, side-by-side compact installation supported

Рабочая температура окружающей среды: -15℃ ~ +50℃ (требуется снижение номинальных характеристик при температуре выше 40 ℃)

Хранилище & Transport Temperature: -40℃ ~ +70 ℃

Относительная влажность: 5% ~ 95%, неконденсирующийся

Altitude Rating: Full power output up to 1000m; 1% power derating per additional 100m above 1000m

Код ТН ВЭД: 85044088

Стандартная конфигурация & Дополнительные аксессуары

Factory Standard Equipment

ACS-AP-S Assistant Control Panel (Chinese language supported)
Built-in Class C2 EMC Filter
Integrated Braking Chopper
Безопасное отключение крутящего момента (СТО) Функция
Triple-protection Coated Printed Circuit Boards
Bottom Cable Entry Compartment
Multilingual Quick Installation & Commissioning Manual

Common Optional Accessories

Enclosure Upgrade: IP55 protective enclosure, flange mounting kit

Communication Extensions: Fieldbus adapters including Profibus DP, Profinet IO, ЭтерНет/IP, Модбус TCP

Electrical Options: Input reactors, output reactors, du/dt filters, sine-wave filters, braking resistors

Functional Extensions: I/O expansion modules, temperature sensor interface cards, NETA-21 remote monitoring module

Software Tools: Drive Composer professional commissioning software

Типичные сценарии применения

Water Treatment Industry: Clean water pumps, sewage pumps, aeration fans, sludge mixers

Building HVAC: Chilled water pumps, cooling water pumps, supply & exhaust fans for central air conditioning

Light Manufacturing: Ленточные конвейеры, packaging production lines, mixing & blending equipment, воздушные компрессоры

Металлургия & Горное дело: Dust extraction fans, material transport belts, mine drainage pumps

Municipal Engineering: Water supply pumping stations, ventilation systems for wastewater treatment plants

Common Troubleshooting Matrix

Явление неисправности	Коренные причины	Step-by-Step Remedial Actions
Overcurrent Trip (Код неисправности 0001)	Short circuit in motor/cables, sudden load surge, overly short acceleration time	1. Cut power and test insulation & wiring of motor and power cables
		2. Appropriately extend acceleration time parameter
		3. Verify consistency between motor rated parameters and drive settings
DC Overvoltage Trip (Код неисправности 0002)	Excessively high mains voltage, overly short deceleration time, faulty braking circuit	1. Measure input mains voltage to confirm it falls within allowable range
		2. Extend deceleration time or enable DC braking function
		3. Check wiring and resistance value of braking resistor for matching
Undervoltage Trip (Код неисправности 0003)	Single-phase power loss, blown input fuses, excessively low mains voltage	1. Inspect three-phase input power to eliminate phase loss issues
		2. Check status of input fuses / автоматические выключатели
		3. Confirm on-site mains voltage meets equipment requirements
Motor Overload Alarm (Код неисправности 0005)	Jammed mechanical load, incorrect motor parameters, sustained overload operation	1. Cut power and rotate motor shaft manually to check mechanical smoothness
		2. Re-run motor identification auto-tune
		3. Evaluate actual load conditions and upsize drive model if necessary
Overheating Fault (Код неисправности 0009)	Чрезмерно высокая температура окружающей среды, blocked cooling air ducts, faulty cooling fan	1. Clear dust buildup on drive air intake cooling grille
		2. Verify normal operation of cooling fan
		3. Improve cabinet ventilation and lower ambient temperature

Detailed List of Standard Accessories for ABB ACS580-01-087A-4 (Frame R5 / IP21 Version)

This model is a standard wall-mounted unit of ACS580 Frame R5. Factory supply contents are split into built-in onboard functions and physical accessories supplied in carton. Below is a detailed breakdown of the official standard supply scope:

Standard Built-in Onboard Functions (Integrated, No Extra Fitting Required)

All functions below are factory pre-configured and ready for direct use without purchasing extra options:

EMC Components: Built-in Class C2 EMC filter to meet industrial site electromagnetic compatibility requirements
Braking Circuit: Integrated braking chopper allowing direct connection of braking resistors for fast deceleration
Safety Function: Безопасное отключение крутящего момента (СТО) compliant with PL e / СИЛ 3 safety level
Охрана окружающей среды: Full triple-protection coating on control and power boards, resistant to humid, dusty and corrosive gas environments
Standard Control Interfaces: 6 цифровые входы, 2 цифровые выходы, 2 аналоговые входы, 1 аналоговый выход
Basic Communications: Embedded RS-485 hardware port with native Modbus RTU protocol support
Структурное проектирование: Bottom cable entry compartment supporting standardized wiring and cable ingress protection
Physical Standard Carton Accessories (Separately Packed Inside Shipment Box)

Independent accessories available upon unpacking for installation and basic commissioning:

ACS-AP-S Assistant Control Panel (Chinese version): Equipped with LCD screen and full-function keys for parameter setup, status monitoring and fault diagnosis; pluggable onto drive front panel and supplied in separate packaging
Wall Mounting Template: 1:1 paper drilling positioning template for marking mounting hole positions on-site to reduce drilling errors
Cable Junction Box Assembly: Standard for Frame R5 IP21 units, including power cable grounding brackets, control cable shielding clamps and assembly fasteners
Mounting Fastener Kit: M6 bolts, nuts and other metal hardware for wall mounting fixation
Ground Terminals & Cable Crimp Accessories: Dedicated main circuit grounding terminals and auxiliary crimp fittings for control terminals

III. Supplied Documentation & Identification Labels

Quick Installation and Startup Guide: Multilingual edition (включая китайский) covering full procedures of wiring, power-up and basic commissioning
Safety Warning Stickers: Multilingual residual voltage warning labels to be affixed near equipment to alert maintenance personnel
Product Certificate of Conformity and Warranty Document

Примечание: Full hardware manuals and firmware parameter manuals are not supplied as standard; downloadable via ABB official website or available as separate printed copies upon order.