Воздушный выключатель ABB E4.2N4000R4000

E4.2N 4000 with Ekip trip unit R4000 — R4000 means the rated current of the electronic trip unit is 4000A

✅ Разбивка модели

E4.2: Размер кадра (Emax2 series, maximum frame rating 4000A)

Н: Короткий-circuit breaking capacity grade N, Icu=66kA @400V AC

4000: Frame rated current Iu=4000A

R4000: Rated current In of Ekip electronic trip unit (Trip unit options: Dip / Трогать / Hi-Touch / G Touch; protection types: БИС / LSIG / ЛИ)

✅ Основные электрические характеристики

Frame rated current Iu: 4000 А

Trip unit rated current In: 4000 А

Номинальное рабочее напряжение Ue: переменного тока 690 В

Номинальное напряжение изоляции Ui: переменного тока 1000 В

Импульсное выдерживаемое напряжение Uimp: 12 кВ

Ику (Ultimate short-circuit breaking capacity): 66 тот (400~690В)

Икс (Service short-circuit breaking capacity): 66 тот

Icw (Кратковременно выдерживаемый ток): 66 kA for 1s; 50 kA for 3s

Механическая выносливость: 15,000 операции

Электрическая выносливость: 5,000 operations at ≤440V; 4,000 operations at 500~690V

✅ Construction & Размеры (Fixed type F, rear horizontal terminals HR, 3П)

3П: W384 × H371 × D270 mm, вес нетто 56 кг

4П: W510 × H371 × D270 mm, вес нетто 70 кг

Terminal options: Rear horizontal HR; optional rear vertical VR; withdrawable W version

Стандартное оснащение: 4 sets of auxiliary contacts, position contacts (Открыть / Закрыто)

✅ Trip Unit Comparison (Key for selection)

1. Командный провал: Базовая версия, нет дисплея, LSI/LSIG
2. Команда Touch: Color display, измерение, communication support, LSI/LSIG
3. Ekip Hi-Touch: Advanced color display, учет энергии, гармонический мониторинг, waveform recording
4. Ekip G Touch: Integrated gateway, встроенный АББ Ability remote communication

LSIG: Long-time L, Short-time S, Мгновенный я, Замыкание на землю G; LSIG includes ground fault protection

✅ Cross-reference & Варианты замены

Same frame variants: E4.2S (Icu 85kA), E4.2H (100тот), E4.2V (150тот)

Внутренняя альтернативная ссылка: Chint NA8-4000, Delixi CDW3-4000, Changshu CW3-4000 (match breaking capacity 66kA)

Upgrade from legacy model: Replaces old-generation Emax E4N 4000

✅ Common Order Codes (3P Fixed HR)

Ekip Dip LSI R4000: 1SDA071192R1

Ekip Touch LSI R4000: 1SDA071195R1

Ekip Hi-Touch LSIG R4000: 1SDA071199R1

ABB Emax2 Ekip (E4.2) Список кодов неисправностей & Communication Commissioning Guide

Applicable to Ekip Dip / Трогать / Hi-Touch / G Touch; Ekip Dip has no screen, only LED alarms; Touch/Hi-Touch support text & numeric fault codes and event logging

Preliminary note: Protection trips (L/S/I/G) are protection events, not hardware faults; 3xxxx numeric codes indicate internal trip unit hardware faults

1. LED Alarm Indications (Common to all Ekip units, for on-site quick diagnosis)

Желтый (Предупреждение)

Горит постоянно: Pre-alarm, protection pre-warning, auxiliary signal alarm

2 flashes per 0.5s: Parameter configuration error

Fast flashing: Rating plug mismatched or not properly fitted

Красный (Сигнализация/отключение)

Горит постоянно: Protection activated & споткнулся, trip command issued

Fast flashing: Sensor disconnection, trip coil open circuit, BF trip failure, protection timing fault

2 flashes every 2s: Rating plug damaged

Желтый + Red fast flashing: Communication lost between main trip board and protection timing module

Желтый + Red slow flashing: Critical internal trip unit fault, contact ABB service

2. On-screen Alarm & Список кодов неисправностей (Touch/Hi-Touch)

🔹 Protection Trip Events (Trip log, check first)

🔹 Hardware / Communication Alarms (Fault alarms, not trips)

Event storage: Touch/Hi-Touch stores up to 200 latest events, with timestamp, fault current and voltage exportable; Ekip Dip has no event storage

3. Ekip Communication Commissioning Guide (Ekip Com Modbus RTU / Модбус TCP)

Communication module types:

Ekip Com Modbus RTU (RS485, 2-wire W1/W2, Модбус РТУ)

Ekip Com Modbus TCP (Ethernet, Модбус TCP)

✅ Ekip Dip has no native communication. Communication requires Touch/Hi-Touch/G Touch plus optional Ekip Com module

3.1 Factory Default Communication Parameters

Модбус РТУ: Скорость передачи данных 19200, Равный паритет, 1 стоп-бит, Slave ID 1

Модбус TCP: DHCP enabled by default; fallback static IP: 192.168.1.100, mask 255.255.255.0

Bus wiring: RS485 W1=A, W2=B; 120Ω terminating resistor required at bus ends

Источник питания: Ekip Com requires 24V DC auxiliary supply (Vaux). Module will not run without 24V!

3.2 Инструменты для ввода в эксплуатацию

1. Ekip Connect (ABB official, предпочтительный): Parameter read/write, bus scan, event export, IP/slave address modification, обновление прошивки, iTEST; supports direct connection via USB T&P test head, independent of field bus
2. Modbus master tools: Modscan, Modbus Poll, ПЛК (Сименс, Schneider etc.)

3.3 Commissioning Steps for RTU RS485

1. Выключить питание, mount Ekip Com Modbus RTU module, connect W1(А) П2(Б), feed 24V DC to module; fit 120Ω terminators at bus ends
2. Включение питания, on trip unit screen: Settings → Communication → Modbus RTU

Enable bus

Set slave address (1~247, unique per bus segment)

Match baudrate & parity with master

3. Connect PC USB-RS485 adapter: A→W1, B→W2; common ground is critical
4. Ekip Connect → Scan → Serial → Configure COM port, baudrate, even parity → Start scan
5. Device found: Read measurements (I/U/P), breaker status, сигналы тревоги; write operations require password authority
6. No device found troubleshooting:

Confirm 24V supply; W1/W2 polarity; common ground; terminator; адресный конфликт; baud/parity mismatch

Подтверждать “Local bus enabled” on trip unit screen

3.4 Commissioning Steps for Modbus TCP

1. Mount Ekip Com Modbus TCP module, supply 24V DC, connect Ethernet to switch
2. On trip unit screen: Settings → Communication → Modbus TCP

DHCP: Enable/Disable; set static IP, subnet, шлюз

Enable Modbus TCP service (Порт 502)

3. Keep PC and module on same subnet, direct cable or via switch
4. Ekip Connect → Scan → Ethernet; or open module IP in browser for read-only web page
5. PLC/SCADA access: Modbus TCP port 502, refer to ABB Ekip Modbus register map

3.5 Access Rights & Пароль

Read measurements & сигналы тревоги: No password required

Modify protection settings, параметры связи, clear events: Engineer password (по умолчанию 000000)

iTEST trip test: Local operation only at connected position; remote test trigger blocked

3.6 Common Communication Pitfalls (E4.2N4000R4000)

1. Missing 24V auxiliary supply: Com module fails to start. CT self-power only supports protection logic, cannot power Com module
2. Ungrounded RS485 bus: Intermittent packet loss and garbled data; single-point grounding for long-distance bus
3. Ekip G Touch has integrated gateway. Do not use together with external Ekip Com, bus conflict will occur
4. Withdrawable breaker: Bus connection inside the cradle is disconnected in test position; communication only available in connected position
5. Modbus register types: Input registers (только для чтения: текущий, Напряжение, статус); Holding registers (read/write: settings, контроль). Remote open/close requires additional Ekip Com Actuator module; standard Com module is read-only, cannot execute remote switching
6. Reset Rules
7. Protection trips (L/S/I/G): Clear fault first, then reset locally (screen reset or remote reset via YR contact)
8. Warning alarms (low battery, SNTP error): Auto clear after root cause removed or manual acknowledge
9. BF trip failure alarm: Mechanical inspection on-site required, manual confirmation to clear alarm

ABB SACE Emax2 ACB Model Specification + Полный список серий + Общие коды заказа

Ряд: Emax2 (successor to legacy Emax E1/E2/E3/E4/E6), стандарт МЭК, widely used ACB in China; Breaking grades by Icu@400V:

B=42kA｜C=50kA｜N=66kA｜S=85kA｜H=100kA｜V=150kA

Trip unit abbreviation:

D = Ekip Dip (нет дисплея, dip-switch setting, LSI/LSIG, no native comms)

T = Ekip Touch (цветной дисплей, измерение, Com module compatible)

HT = Ekip Hi-Touch (цветной дисплей, гармонический, recording, power quality)

GT = Ekip G Touch (integrated gateway, ABB Ability)

Protection types: ЛИ / БИС / LSIG (G=ground fault)

Монтаж: F Fixed; W Withdrawable; Terminals HR Rear Horizontal, VR Rear Vertical; 3П/4П

Full model example: E4.2N 4000 Ekip Touch LSIG 3P F HR, matching your E4.2N4000R4000

1. Frame Overview (4 Emax2 frame sizes)

Примечание: Суффикс “.2” stands for Emax2; old Emax E1/E2/E4/E6 without “.2” are phased out

2. Full Model Description Breakdown

`E4.2 N 4000 Ekip Touch LSIG 3P F HR`

1. E4.2: Размер кадра
2. Н: Класс отключающей способности
3. 4000: Frame rated current Iu
4. Команда Touch: Тип расцепителя
5. LSIG: Кривая защиты
6. 3П: Номер полюса
7. Ф: Mounting F Fixed / W Withdrawable
8. HR: Terminal HR Rear Horizontal / VR Rear Vertical / FR Front

Rating Plug Rxx: R4000=In=4000A; R3200=In=3200A, R value ≤ Frame Iu

3. Basic Model List

✅ E1.2 (630~1600А)

E1.2B 630 / 800 /1000 /1250 /1600

E1.2C 630 / 800 /1000 /1250 /1600

E1.2N 630 / 800 /1000 /1250 /1600

✅ E2.2 (800~2500А)

E2.2B 800 /1000 /1250 /1600 /2000 /2500

E2.2N 800 /1000 /1250 /1600 /2000 /2500

E2.2S 800 /1000 /1250 /1600 /2000 /2500

E2.2H 800 /1000 /1250 /1600 /2000 /2500

✅ E4.2 (2000~4000А)

E4.2N 2000 /2500 /3200 /4000

E4.2S 2000 /2500 /3200 /4000

E4.2H 2000 /2500 /3200 /4000

E4.2V 2000 /2500 /3200 /4000

✅ E6.2 (4000~6300А)

E6.2H 4000 /5000 /6300

E6.2V 4000 /5000 /6300

4. Standard Order Codes (1SDA prefix, 3P Fixed HR, no motor/YO/YC accessories)

Правило: Order code changes with trip unit; separate codes for W withdrawable and 4P versions

E1.2N 1600

Ekip Dip LSI R1600: 1SDA070492R1

Ekip Touch LSI R1600: 1SDA070495R1

Ekip Touch LSIG R1600: 1SDA070496R1

Ekip Hi-Touch LSIG R1600: 1SDA070499R1

E2.2N 2500

Ekip Dip LSI R2500: 1SDA070892R1

Ekip Touch LSI R2500: 1SDA070895R1

Ekip Touch LSIG R2500: 1SDA070896R1

Ekip Hi-Touch LSIG R2500: 1SDA070899R1

E4.2N 4000

Ekip Dip LSI R4000: 1SDA071192R1

Ekip Touch LSI R4000: 1SDA071195R1

Ekip Touch LSIG R4000: 1SDA071196R1

Ekip Hi-Touch LSIG R4000: 1SDA071199R1

E4.2S 4000

Ekip Dip LSI R4000: 1SDA071212R1

Ekip Touch LSI R4000: 1SDA071215R1

Ekip Hi-Touch LSIG R4000: 1SDA071219R1

E6.2H 6300

Ekip Touch LSI R6300: 1SDA071455R1

Ekip Touch LSIG R6300: 1SDA071456R1

Ekip Hi-Touch LSIG R6300: 1SDA071459R1

5. Communication Module Order Codes (Ekip Com)

Ekip Com Modbus RTU: 1SDA073440R1

Ekip Com Modbus TCP: 1SDA073441R1

Ekip Com Profibus: 1SDA073442R1

Ekip Com IEC61850: 1SDA073444R1

Ekip Com Actuator (remote switching module): 1SDA073446R1

6. Common Accessory Order Codes (Продается отдельно, not included in breaker body)

Closing coil YC AC220: 1SDA073300R1

Opening coil YO AC220: 1SDA073304R1

Motor operator M AC220: 1SDA073310R1

Auxiliary contacts 4CO: 1SDA073320R1

Signal contacts 2CO: 1SDA073322R1

RTC battery kit: 1SDA073470R1

Rating Plug R4000: 1SDA072944R1

7. Важные примечания
8. The above base codes default to 3P, Fixed F, Rear Horizontal HR. Codes change for 4P / W withdrawable / VR vertical terminals
9. Quotation is combinational: Breaker body + мотор + YO + YC + communication module are separate line items. Breaker body does not come with motor or coils as standard
10. Ekip Dip has no communication. Touch/Hi-Touch need Ekip Com module for Modbus
11. Legacy Emax (non .2) order codes start with 1SDA05, parts and trip units are not interchangeable with Emax2