Контактор,автоматический выключатель,датчик,Кодер,ПЛК,Конвертер
TTH200: АББ TTH200 series DIN-rail mount temperature transmitter (Head Mount / DIN rail dual mounting, HART-протокол)
Y0: Версия / код конфигурации, stands for without local display, базовая модель, HART 4-20mA output, Монтаж на DIN-рейку.
Series positioning: The TTH200 is a 2-wire HART temperature transmitter from ABB. It accepts RTD, TC, mV and resistance signals, and serves as a replacement for the discontinued TTF200.
Ключевые характеристики
Источник питания: 12～42V DC, 2-проволока
Выход: 4–20 мА + HART 5/7
Sensor Inputs:
РТД: Пт100, Пт1000, Cu50, и т. д.. Supports 2/3/4-wire connection
TC: Б,Э,Дж,К,л,Н,Р,С,Т,U and other thermocouple types
Millivolt mV, resistance signal
Точность: RTD typical ±0.05℃; Thermocouple typical ±0.08℃
Монтаж: Крепление на DIN-рейку; also can be installed inside sensor connection head (head mount)
Жилье: Пластиковый корпус, IP20 (under DIN rail installation)
Конфигурация: HART communicator, ABB Device Manager, DTM/FDT software
Suffix code Y0: No local LCD display, basic version without extra hardware options.
Сравнение: Y1 = with LCD display
Типичные применения
Industrial temperature measurement for HVAC, химический, power and pharmaceutical industries. Used for temperature acquisition on pipelines and tanks, connected to DCS or PLC, paired with Pt100, K-type thermocouples.
Выбор модели & Замена
- Та же серия: TTH200-Y1 (с дисплеем)
- Legacy model replacement: TTF200 → TTH200
- Отечественная альтернатива: HART DIN rail temperature transmitters (such as Chongqing Chuanyi, Shangrun HART models)
Распространенное устранение неполадок
- Нет вывода: Verify loop voltage ≥12V, check 2-wire wiring for short circuit and polarity
- Fixed at 4mA: Обрыв цепи датчика / not connected, mismatched configured sensor type (например. Pt100 configured while K thermocouple wired)
- Температурный дрейф: Check RTD wiring (4-wire preferred), cold junction compensation setting for thermocouple
- Сбой связи HART: 250Ω resistor inserted into loop, avoid high-power interference, verify HART address
Запчасти & Примечания к покупке
Complete order number is not limited to TTH200-Y0; extra codes for sensor type, explosion protection are required
Explosion-proof versions have separate suffixes; TTH200 has intrinsically safe Ex ia variants, confirm explosion-proof requirement before purchase
HS code reference: 90268000 (Датчик температуры, industrial measuring instrument)
ABB TTH200 Complete Ordering Selection Table
Order model structure: TTH200 [Explosion-proof code] [Display code] + [Additional options]
Примеры: TTH200-Y0 = Non-explosion proof, without LCD; TTH200-S1-Y0 = NEPSI intrinsically safe, without LCD
- Взрывозащита / Certification Code (1st suffix segment)
| Код | Описание | Приложение |
| Y0 | Non-explosion proof, стандартный тип (your current model) | Non-hazardous area, control room DIN rail mounting |
| Е1 | ATEX intrinsically safe Ex ia IIC T6 | Zone0/1/2, European explosion protection |
| Е2 | ATEX non-sparking Ex nA / Ex ec IIC T6 | Zone2 only |
| H1 | IECEx intrinsically safe Ex ia IIC T6 | International explosion-proof certificate, overseas projects |
| S1 | NEPSI intrinsically safe Ex ia IIC T6 Ga | Widely used in domestic chemical industry with Chinese explosion-proof certificate |
| Л1 | FM Intrinsically Safe (Северная Америка) | North America Class I Div.1 |
| Л2 | FM Non-incendive (Северная Америка) | North America Class I Div.2 |
| Р1 | CSA Intrinsically Safe (Канада) | Canada projects |
| Р2 | CSA Non-incendive (Канада) | Canada Class I Div.2 |
| П2 | EAC-Ex + Russian metrology certification | Russian federation explosion-proof projects |
| Г1 | Russian metrology certification (non-explosion proof) | Russian non-hazardous area |
| G3 | Kazakhstan metrology certification | Kazakhstan non-hazardous area |
| Т2 | Kazakhstan EAC-Ex + metrology certification | Kazakhstan explosion-proof projects |
| М5 | Belarus metrology certification | Belarus non-hazardous area |
| U2 | Belarus EAC-Ex + metrology certification | Belarus explosion-proof projects |
- Display Code
| Код | Описание |
| Y0 | Без ЖК-дисплея (базовая модель, preferred for DIN rail installation) |
| Y1 | With local LCD display, for on-site temperature reading and alarm check |
✅ Combination example: TTH200-Y0 (non-explosion proof no display); TTH200-E1-Y1 (ATEX intrinsically safe + ЖК-дисплей)
- Жилье / Mounting Accessory Options (added separately, incompatible with some explosion-proof models)
| Код | Housing Description | IP-рейтинг | Примечания |
| H1 | Aluminum head housing 80×75×57mm, 2×M16 cable glands | IP65 | Sensor head mount |
| Н2 | Polyester housing 75×80×55mm, 2×M16 | IP65 | Устойчивость к коррозии |
| Н3 | Polycarbonate housing 80×82×55mm, 2×M16 | IP65 | Экономически эффективный |
| H6 | Aluminum large housing 175×80×57mm, 1×M16+2×M20 | IP65 | Large enclosure |
| H7 | Polyester large housing with separate terminal block | IP65 | Split terminal |
| H8 | Polyester large housing without separate terminal block | IP65 | Compact large housing |
| DIN rail kit | 3KXT091230L0001 (10 наборы) / 3KXT091230L0002 (1 набор) | DIN35 rail mounting bracket | Optional for Y0/Y1 DIN rail installation |
⚠️ Примечание: Some explosion-proof models cannot be matched with H1/H2/H3 head housing options. Confirm before order.
- Functional Additional Options
| Код | Option Description |
| CS | SIL2 compliance declaration (for safety instrumented SIL2 loop) |
- Supported Sensor Input Selection (configured in software, stated in order remarks)
RTD Resistance Temperature Detector
Пт100(IEC60751 0.00385)【Default】、Пт100(JIS)、Pt10、Pt50、Pt200、Pt500、Пт1000；Ni50/Ni100/Ni120/Ni1000；Cu10/Cu100；Resistance signal 0~500Ω / 0~5000Ω; support 2/3/4-wire
Thermocouple TC
К、Дж、Т、Э、Н、Р、С、Б、л(DIN43710)、ты、С、Д；mV signal: -125~125mV / -125~1100mV
Cold junction compensation: Встроенный(по умолчанию) / external cold junction / no compensation (B-type thermocouple recommended no compensation)
- General Technical Specifications
| Элемент | Параметр |
| Протокол | HART5 / ХАРТ7, 2-wire 4-20mA |
| Источник питания | 12~42V DC |
| Точность | RTD typical ±0.05℃; TC typical ±0.08℃ |
| Температура окружающей среды | Transmitter body: -40~+85℃; Explosion-proof T6 version max 56℃ |
| NAMUR | NE89, NE107 (сигнализация неисправности) |
| Уровень безопасности | SIL2 capable (with CS option) |
| Configuration Tool | HART communicator, ABB Device Manager, ФДТ/ДТМ |
- Complete Ordering Examples
- TTH200-Y0
Non-explosion proof, no LCD, Монтаж на DIN-рейку; configured Pt100, range 0~200℃
- TTH200-S1-Y1+CS
NEPSI intrinsically safe, with LCD, SIL2 declaration; Термопара типа К, built-in cold junction compensation
- TTH200-E1-Y0+H2
ATEX intrinsically safe, no LCD, polyester IP65 head housing, head mount Pt100
- Примечания к выбору
- Y0/Y1 are display codes, NOT explosion-proof codes, a common confusion. For TTH200-Y0, Y0=no display; the preceding Y means non-explosion proof.
- DIN rail installation only needs transmitter body + DIN rail clip kit, no H1/H2 head housing. H-series housings are used for sensor head mounting inside temperature probe junction box.
- Confirm hazardous area classification (Zone/Div) and temperature class T6 for explosion-proof models; NEPSI S1 version is preferred for domestic hazardous projects.
- Measurement range, sensor type and TAG are configuration parameters, submit in order remarks for factory pre-configuration; or configure on-site via HART communicator after delivery.
- Cross Series Replacement Reference
TTH200: Один канал, no sensor drift monitoring (эта модель)
ТТХ300: Dual channel, support sensor redundancy and drift monitoring, более высокая производительность
Legacy TTF200: Снято с производства, direct replacement by TTH200-Y0/Y1
ABB TTH200 Full Model List (Head Mount / DIN Rail Dual Purpose Temperature Transmitter)
Model structure: TTH200-[Explosion-proof code]-[Display code] [+Additional options]
Base series: TTH200 (single channel, HART 4-20mA); ТТХ300 (dual channel) in same family listed at the end for distinction
- TTH200 Base Model List (Combination of Explosion Protection & Отображать)
| Полная модель | Explosion Certification | Отображать | Описание |
| TTH200-Y0 | Non-explosion proof | Without LCD | Non-hazardous area, DIN-рейка / head mount, ваша целевая модель |
| TTH200-Y1 | Non-explosion proof | With LCD | Non-hazardous area, local temperature reading |
| TTH200-S1-Y0 | NEPSI intrinsically safe Ex ia IIC T6 | Without LCD | Domestic chemical hazardous area, Chinese explosion-proof certificate |
| TTH200-S1-Y1 | NEPSI intrinsically safe Ex ia IIC T6 | With LCD | Domestic hazardous area + local display |
| TTH200-E1-Y0 | ATEX intrinsically safe Ex ia IIC T6 | Without LCD | EU ATEX intrinsically safe, Zone0/1 |
| TTH200-E1-Y1 | ATEX intrinsically safe Ex ia IIC T6 | With LCD | ATEX intrinsically safe + ЖК-дисплей |
| TTH200-E2-Y0 | ATEX Ex nA / Ex ec IIC T6 | Without LCD | ATEX non-sparking, Zone2 only |
| TTH200-E2-Y1 | ATEX Ex nA / Ex ec IIC T6 | With LCD | Zone2 explosion-proof + отображать |
| TTH200-H1-Y0 | IECEx intrinsically safe Ex ia IIC T6 | Without LCD | International IECEx certificate, overseas project |
| TTH200-H1-Y1 | IECEx intrinsically safe Ex ia IIC T6 | With LCD | IECEx intrinsically safe + ЖК-дисплей |
| TTH200-L1-Y0 | FM intrinsically safe Class I Div.1 | Without LCD | North America FM intrinsically safe |
| TTH200-L1-Y1 | FM intrinsically safe Class I Div.1 | With LCD | North America FM intrinsically safe + отображать |
| TTH200-L2-Y0 | FM Non-incendive Class I Div.2 | Without LCD | North America Div.2 |
| TTH200-L2-Y1 | FM Non-incendive Class I Div.2 | With LCD | North America Div.2 + отображать |
| TTH200-R1-Y0 | CSA intrinsically safe Class I Div.1 | Without LCD | Canada CSA intrinsically safe |
| TTH200-R1-Y1 | CSA intrinsically safe Class I Div.1 | With LCD | Canada CSA intrinsically safe + ЖК-дисплей |
| TTH200-R2-Y0 | CSA Non-incendive Class I Div.2 | Without LCD | Canada CSA Div.2 |
| TTH200-R2-Y1 | CSA Non-incendive Class I Div.2 | With LCD | Canada CSA Div.2 + отображать |
| TTH200-P2-Y0 | EAC-Ex Russian explosion-proof + metrology cert | Without LCD | Russian federation explosion-proof project |
| TTH200-P2-Y1 | EAC-Ex Russian explosion-proof + metrology cert | With LCD | Russian explosion-proof + отображать |
| TTH200-G1-Y0 | Russian metrology cert (non-explosion proof) | Without LCD | Russian non-hazardous area |
| TTH200-G1-Y1 | Russian metrology cert (non-explosion proof) | With LCD | Russian non-hazardous area + ЖК-дисплей |
| TTH200-G3-Y0 | Kazakhstan metrology cert (non-explosion proof) | Without LCD | Kazakhstan non-hazardous project |
| TTH200-G3-Y1 | Kazakhstan metrology cert (non-explosion proof) | With LCD | Kazakhstan non-hazardous + ЖК-дисплей |
| TTH200-T2-Y0 | Kazakhstan EAC-Ex + metrology cert | Without LCD | Kazakhstan explosion-proof project |
| TTH200-T2-Y1 | Kazakhstan EAC-Ex + metrology cert | With LCD | Kazakhstan explosion-proof + ЖК-дисплей |
| TTH200-M5-Y0 | Belarus metrology cert (non-explosion proof) | Without LCD | Belarus non-hazardous area |
| TTH200-M5-Y1 | Belarus metrology cert (non-explosion proof) | With LCD | Belarus non-hazardous + ЖК-дисплей |
| TTH200-U2-Y0 | Belarus EAC-Ex + metrology cert | Without LCD | Belarus explosion-proof project |
| TTH200-U2-Y1 | Belarus EAC-Ex + metrology cert | With LCD | Belarus explosion-proof + ЖК-дисплей |
- Additional Options (appended after any model with `+`)
| Суффикс-код | Описание |
| +CS | SIL2 compliance declaration for SIL2 safety loops |
| 0 | Aluminum head housing IP65, 2×M16 cable glands |
| 0 | Polyester head housing IP65, 2×M16 cable glands, устойчивый к коррозии |
| 0 | Polycarbonate housing IP65, 2×M16 cable glands |
| 0 | Aluminum large housing IP65, 1×M16+2×M20 |
| 0 | Polyester large housing with separate terminal block |
| 0 | Polyester large housing without separate terminal block |
Example complete order number: `TTH200-S1-Y0+CS+H2`
Значение: NEPSI intrinsically safe, нет дисплея, SIL2 declaration, polyester IP65 head housing
III. TTH / TTF Family Comparison (Избегайте ошибок выбора)
| Модельная серия | Канал | Автобус | Функции |
| TTH200 | Одинокий | HART 4-20mA | Head / DIN rail dual mount, no sensor drift monitoring, this series |
| ТТХ300 | Двойной | HART / Profibus PA / FF | Dual sensor input, support sensor redundancy & drift monitoring |
| TTF200 | Одинокий | HART | Field mount integral housing transmitter (not head module), legacy discontinued, replaced by TTH200 |
| TTF300 | Двойной | HART / Пенсильвания / FF | Field housed dual channel temperature transmitter |
| TTF300-W | Двойной | WirelessHART | WirelessHART field temperature transmitter |
- Common Technical Features of TTH200 Series
- Universal input: РТД / TC / Ой / мВ, configured in software, not coded in model number, state in order remarks
- 2-проволока: 12~42VDC, 4-20mA+HART5/HART7
- NAMUR NE89, NE107 fault alarm
- Two mounting forms: DIN-рейка (transmitter module only); Sensor head mount (transmitter + H-series housing kit)
- Purchasing Remarks
Y0/Y1 always as the last segment: Y0 no display, Y1 with LCD; preceding code for explosion-proof / regional certification
H-series housing is additional option, not part of base model; H housing not required for DIN rail installation
СИЛ(CS) is compliance declaration without hardware modification; add suffix `+CS` for SIL2 safety loop application
Диапазон, тип датчика, TAG are configuration parameters, not embedded in model code, add to order remarks for factory pre-configuration
