โต๊ะสไลด์ลมแม่นยำ SMC MXS6-30

MXS: Dual-cylinder air slide table with cross-roller guide; Bore 6 mm, Stroke 30 mm, ประเภทมาตรฐาน, double-acting, built-in magnet, rubber bumpers at both ends

1. คำอธิบายรหัสรุ่น

MXS6-30

MXS: บตท air slide table series (cross-roller guide, dual-cylinder construction)

6: Bore size φ6 mm (dual-cylinder structure)

30: Standard stroke 30 mm

Common suffix extensions:

เช่น: Front-end stroke adjuster; วิทยาศาสตรบัณฑิต: Rear-end stroke adjuster; ที่: Dual-end stroke adjuster

บี: Hydraulic shock absorber; ล: Mirror-image body

–M9BW /-A93: Factory-fitted auto-switches

2. ข้อมูลจำเพาะทางเทคนิคหลัก

น้ำหนัก: ประมาณ. 0.22 กก; Optimized for horizontal mounting, suitable for precision short-stroke transfer, positioning and jig actuation.

3. Mounting Highlights
4. การติดตั้งสามด้าน: สูงสุด, bottom and side mounting options. Side thread M2.5×0.45. Avoid over-torque and excessive screw depth to prevent guide deformation and jamming.
5. Worktable tapped holes M4 for workpiece/fixture mounting.
6. Allowable load is governed by moment and overhang length, not only thrust. Longer overhang reduces allowable load.
7. Compatible auto-switches: D-M9B/M9N/A93/Z73. Switches install in body T-slots; switches remain stationary (do not travel with slide table).
8. ตัวอย่างโมเดลที่สมบูรณ์ทั่วไป

MXS6-30AS: Front-end stroke adjustable (0-5 mm adjustment range)

MXS6-30BS: Rear-end stroke adjustable

MXS6-30AT: Both-ends adjustable

MXS6-30B: Dual-end hydraulic shock absorbers for reduced impact

MXS6-30-M9BW: Pre-fitted with two M9BW auto-switches

5. Domestic Drop-in Replacements (Identical mounting footprint)

อาร์กติก: HLQ6-30；เชลิค: MDX6-30；Direct mechanical interchangeable.

6. ใช้แล้ว / Second-hand Unit Inspection Checklist
7. Supply air at 0.3-0.4 MPa; full-travel smooth operation without sticking or crawling.
8. Inspect rubber bumpers for cracking and aging.
9. Check lateral play of worktable: Excessive side clearance indicates worn cross-roller guide.
10. Air test full-stroke travel; no internal or external air leakage.
11. Verify built-in magnet integrity: Auto-switch shall produce valid signal at both end-of-travel positions.
12. การใช้งานทั่วไป

Small-scale automation equipment, การประกอบอุปกรณ์อิเล็กทรอนิกส์, jig push-pull, sorting mechanism, miniature transfer positioning.

SMC MXS6-30 Practical Application Cases

MXS6-30 is a φ6 mm bore, 30 mm stroke air slide table with cross-roller guide. Compact size and good moment-resistance capability make it ideal for light-load short-stroke reciprocation. Max allowable horizontal load: ประมาณ. 0.6 กก. Widely used in electronics, lithium-ion battery, inspection and small custom automation machines.

Case 1: Electronic component pick-and-place (Consumer electronics assembly machine)

สภาพการทำงาน: Equipped with miniature pneumatic gripper. 30 mm horizontal reciprocation transfers small PCB components from feeder into positioning jig. Cycle time:1.2-2 s/cycle, load 150-250 g.

Selected Model: MXS6-30-M9BW, dual-end auto-switch position feedback.

Design Notes: Minimize overhang. Install flow control valves to set speed 150-250 mm/s to reduce impact. Mount gripper directly onto worktable; body fixed from bottom side.

Why MXS6-30: Superior lateral rigidity compared to MXS-U series. Stable repeatability for reciprocation. Space-saving alternative to servo modules for cost reduction.

Case 2: Camera / Sensor feed positioning (Vision inspection equipment)

สภาพการทำงาน: Drives industrial camera or laser sensor for 30 mm forward-backward offset to inspect workpieces of variable thickness. Stationary imaging at target position, low-frequency cycling.

Selected Model: MXS6-30AS (front-end stroke adjuster, 0-5 mm fine-tuning for inspection distance).

หมายเหตุ: Avoid long overhang; mount load close to worktable surface. Stabilize supply air pressure to minimize position deviation caused by pressure fluctuation.

การใช้ในอุตสาหกรรม: Connector appearance inspection, plastic part sorting machines.

Case 3: Jig stop / Workpiece positioning (Conveyor line)

สภาพการทำงาน: Stop and pre-position workpieces on conveyor. Slide extends to block workpiece; retracts to release after inspection. 30 mm stroke provides stop-and-clear function.

Selected Model: Standard MXS6-30 with D-A93 auto-switches.

การติดตั้ง: Side-wall mounting to save vertical machine height.

บันทึก: Only for light-workpiece stopping. Cannot sustain heavy impact; add dedicated bumper block for high-impact scenarios.

Case 4: Mini-press-fit & connector insertion (Connector assembly equipment)

สภาพการทำงาน: Light pre-press for small connectors and FPC flexible circuits. Slide extends for pre-compression and retracts for retraction. Theoretical extend thrust 27 N @0.5 MPa; suitable only for light-force pressing, not heavy press-fit tasks.

Selected Model: MXS6-30B (hydraulic shock absorber) for high-impact cycles to protect delicate connectors.

การแจ้งเตือน: If higher pressing force is required, upgrade to MXS8-30.

Case 5: Small-format lithium-ion cell / electrode sorting mechanism

สภาพการทำงาน: Divert qualified / NG miniature soft-pack cells into different bins via 30 mm horizontal push.

Selected Model: MXS6-30-M9N, non-lube design for low-oil-mist battery-plant environment.

Constraints: Load ≤300 g. Long overhang will accelerate guide wear.

Case 6: Reagent-card / Test-strip pushing for compact medical diagnostic equipment

สภาพการทำงาน: Position reagent cards and test strips in light-load clean-environment setup. Non-lube operation eliminates oil-mist contamination risk.

Selected Model: Standard MXS6-30 with built-in magnet and solid-state auto-switches.

บันทึก: Install air-line oil-mist remover for medical-grade air quality.

Case 7: Single-axis for XY gantry (Compact 2-axis transfer platform)

สภาพการทำงาน: MXS6-30 as X-axis stacked upon second slide table for simple pneumatic XY pick-and-place.

หมายเหตุ: Total mass of upper-axis assembly plus workpiece must not exceed allowable load of lower-axis. Avoid large overhang.

⚠️ Common Pitfalls for MXS6-30 Selection

1. Max allowable horizontal load 0.6 kg. Allowable load decreases sharply with longer overhang. Moment capacity, not raw thrust, is the primary limiting factor.
2. 30 mm is the optimal stroke for bore 6. Rigidity degrades significantly for stroke >40 มม.
3. For high-frequency cycling and impact-prone applications, choose -B hydraulic-shock-absorber variant; standard rubber bumpers degrade rapidly under continuous high-speed operation.
4. MXS6-30 vs MXQ6-30: MXS uses cross-roller guide with superior moment resistance. MXQ uses ball-bearing guide for lower friction but weaker anti-moment performance, suited for ultra-light-load duty.

SMC MXS6-30 Complete Mounting Instructions

MXS6-30 supports bottom-mount, side-mount and top-mount. Worktable for workpiece mounting; main body fixed to machine frame.

1. Thread Specifications & Tightening Torques (SMC factory specification)
2. การติดตั้งร่างกาย (fix cylinder body to machine frame)

Side mounting threads: M2.5×0.45, Max tightening torque 0.5 N·m, Max screw insertion depth 3.5 mm

⚠️Excess-length screws will compress internal guide assembly and cause jamming or permanent damage!

Bottom mounting threads: M2.5×0.45, Max torque 0.5 N·m

2. Worktable (mount fixture / workpiece)

Table tapped holes: M4×0.7, Max tightening torque 1.2 N·m

Worktable is moving cross-roller guide assembly. Never over-torque.

3. Air port thread

ท่าเรือ: M3×0.5, compatible with miniature pneumatic fittings.

สำคัญ: M2.5 screws require low torque value. Torque wrench recommended; do not rely on hand-feel.

2. Four Mounting Configurations

1) Bottom-mount (ที่พบบ่อยที่สุด, horizontal orientation)

Fasten screws upward through bottom-body tapped holes. Slide table faces upward, horizontal reciprocation.

แอปพลิเคชัน: Transfer, push-pull, vision feed.

ข้อได้เปรียบ: Best-case loading condition, maximum allowable load capacity.

บันทึก: Screw insertion depth ≤3.5 mm. Do not contact internal guide components.

2) Side-mount (Wall-mount lateral installation)

Fasten into lateral body tapped holes. Slide table performs horizontal motion while unit stands on its side.

แอปพลิเคชัน: Conveyor-line stop mechanisms, limited-height machine layout.

Side-mount increases applied moment. Derate allowable load. Mount workpieces as close to table surface as possible.

3) Top-mount (Overhead / inverted mounting)

Fasten body from above. Cylinder hangs upside-down; worktable moves downwards.

Inverted mounting: Workpiece weight fully loads guide system. Load must be derated. Not suitable for high-speed high-cycle operation.

4) Vertical-axis mounting (Up-down motion)

Slide travel oriented vertically. Worktable moves up and down.

❗Risk: Workpiece weight directly alters cushioning performance. Flow-control valves mandatory for low-speed operation. Not for heavy payloads. Recommended vertical-mount payload ≤150 g.

3. Auto-Switch Installation
4. Auto-switches (D-M9BW / D-A93) install in T-slots on both sides of stationary body, not on moving worktable.
5. Loosen slot-clamping screw, slide auto-switch to desired trigger position, ขันอีกครั้ง.
6. T-slots available on both sides; 1 หรือ 2 auto-switches may be fitted.
7. Mounting Procedure
8. Pre-tighten all body-mount screws first, then progressively torque each screw to specified value. Do not fully tighten one screw before others, to avoid body distortion.
9. Mount workpiece onto worktable via M4 screws, observe torque limits.
10. Air test at 0.3-0.4 MPa for full-stroke smooth operation without sticking.

If jamming occurs: Almost always caused by screws inserted too deep compressing cross-roller guide; reduce screw insertion depth.

4. Install flow-control fittings; set piston speed not to exceed 500 mm/s.
5. Adjust auto-switch positions and confirm end-of-travel signal integrity.
6. Critical Mounting Prohibitions (Frequent Failure Sources)
7. Screw insertion depth must never exceed 3.5 mm. Over-length M2.5 screws will destroy guide assembly.
8. Do not apply lateral / transverse external forces to worktable; avoid shock-loading the slide.
9. Never strike body or worktable after installation; cross-roller pre-load will be lost, creating backlash.
10. Vertical-mount applications: Workpiece weight impairs rubber-bumper performance. Select -B hydraulic-shock-absorber model for frequent vertical cycling.
11. Do not specify load purely by thrust rating; calculate applied moment. Max allowable moment for MXS6-30: 1.2 น.ม.
12. Stacked Multi-axis Mounting (XY Platform)