المقاولين,قاطع الدائرة,الاستشعار,التشفير,بلك,محول
CP1L: CP1L series PLC مدمج
م: 10K program steps (L = 5K steps)
40: Total built-in I/O = 40 نقاط (24 المدخلات / 16 النواتج)
د.ت: مخرج الترانزستور
1: بنب (sourcing) (DT without 1 = NPN sinking)
د: تيار مستمر 24 فولت مزود الطاقة
المواصفات الكهربائية الأساسية
مزود الطاقة: تيار مستمر 24 فولت, allowable range 20.4～26.4V, max power consumption 20W
Built-in inputs: 24 points DC24V, NPN/PNP universal input
Built-in outputs: 16 points PNP transistor, 0.3أ لكل نقطة
Program capacity: 10خطوات ك; Data memory: 32كلمات ك
Instruction speed: 0.55μs per basic instruction
High-speed counter: 4 محاور, الحد الأقصى 100 كيلو هرتز
Pulse output: 2 محاور, الحد الأقصى 100 كيلو هرتز (for stepper/servo drives)
Onboard ports: USB programming port (no built-in Ethernet or serial port)
Expansion capability: حتى 3 CP-series expansion units, maximum total I/O 160 نقاط; optional communication boards (RS232/485), supports Modbus-RTU, إلخ.
Built-in RTC real-time clock; battery-backed holding memory; operating temperature 0～55℃
سيناريوهات التطبيق النموذجية
Small automated equipment, خطوط الناقل, آلات التعبئة والتغليف, test benches, custom jigs, stepper & servo positioning control. Ideal for PNP output to match European standard sensors and drives.
Comparison with Similar Models (الارتباك المشترك)
CP1L-M40DT-D: NPN sinking transistor output, other hardware identical
CP1L-M40DR-D: تتابع الإخراج, no high-speed pulse support
CP1L-EM40DT1-D: Ethernet integrated version
CP1H-XA40DT1-D: Higher-performance CP1H series with built-in analog channels
اختيار & ملاحظات الاستبدال
- Critical distinction during replacement: DT1 = PNP sourcing; DT = NPN sinking. Reverse polarity connection may damage output circuits directly.
- No onboard serial port. Modbus communication with HMI or inverters requires optional CP1W-CIF01/11 communication boards.
- برامج البرمجة: مبرمج CX (CX-P), يدعم مخطط السلم, مخطط كتلة الوظيفة, نص منظم.
- Replacement options for phase-out: CP1E-N40DT1-D or NX1P compact NX series.
Troubleshooting for Common Faults
No pulse output: Verify output polarity matches servo/stepper drive signal type; check pulse output bits, frequency and axis parameters.
فشل الاتصالات: Confirm communication board model, port number, baud rate and slave address; fit 120Ω terminating resistors at both ends of RS485 bus.
RUN indicator off after power-up: Check fatal program errors, PLC mode switch and battery fault.
Programming Software for اومرون CP1L-M40DT1-D
Main software: مبرمج CX (CX-P) — Standard programming tool for OMRON CP-series PLC
✅ Minimum supported version: Ver7.10; مُستَحسَن: Ver9.3 / 9.4 / 9.5 (stable for Win10/Win11)
✅ Software suite: CX-One (full package) / CX-One Lite (lightweight version, only for small PLCs such as CP/CPM)
Supported Programming Languages
مخطط السلم (إل دي)
مخطط كتلة الوظيفة (FBD)
نص منظم (شارع)
Sequential Function Chart (SFC)
Supporting Tools (included in CX-One package)
- CX-Simulator: Offline simulation, program debugging without physical PLC
- CX-Designer: HMI screen programming for OMRON NB/NS/NV touch panels
- CX-Drive: OMRON inverter parameter setup
- مُتكامل تجربة العملاء: Network configuration
Communication Methods (CP1L-M40DT1-D)
Onboard USB-B port, connect PC via standard USB printer cable; select USB network type in software.
With optional communication boards (CP1W-CIF01/11), online communication via RS232/485 Modbus-RTU is available.
Version Recommendation
Only CP1L / CP1E programming: Install CX-One Lite V4, compact and sufficient
Also programming CJ/CS/NX large PLCs: Install full CX-One V4
⚠️ ملحوظة: SYSMAC Studio (NX series dedicated software) cannot be used for CP1L. It is exclusively for NX1P/NX7 and incompatible.
توافق النظام
CX-P 9.x: Win7 / Win10 / Win11 (64-قليل)
إصدار 7.1: Mainly for Win7; driver issues frequent on Win11
New Project Setup Guide
Device type: CP1L-M40DT1-D
CPU model: CP1L-M40DT1-D
نوع الشبكة: USB (تقصير)
- Model Prefix Rules
L = 5K steps (اقتصاد); M = 10K steps (معيار, this model belongs to M)
هو / EM = Ethernet enabled; no E = USB only
DR = Relay output; DT = NPN sinking transistor; DT1 = PNP sourcing transistor
-A = AC220V supply; -D = DC24V supply
- Non-Ethernet Standard Models (CP1L-L / CP1L-M, USB only)
1) CP1L-L (5خطوات ك, اقتصاد)
① 14-point (8 المدخلات + 6 النواتج)
إمداد التيار المتردد: CP1L-L14DR-A (تتابع), CP1L-L14DT-A (نبن)
إمدادات العاصمة: CP1L-L14DR-D, CP1L-L14DT-D (نبن), CP1L-L14DT1-D (بنب)
② 20-point (12 المدخلات + 8 النواتج)
إمداد التيار المتردد: CP1L-L20DR-A, CP1L-L20DT-A
إمدادات العاصمة: CP1L-L20DR-D, CP1L-L20DT-D, CP1L-L20DT1-D
2) CP1L-M (10خطوات ك, معيار, this model’s series)
① 30-point (18 المدخلات + 12 النواتج)
تكييف: CP1L-M30DR-A, CP1L-M30DT-A
العاصمة: CP1L-M30DR-D, CP1L-M30DT-D, CP1L-M30DT1-D
② 40-point (24 المدخلات +16 النواتج, نموذج الهدف)
تكييف: CP1L-M40DR-A, CP1L-M40DT-A
العاصمة: CP1L-M40DR-D, CP1L-M40DT-D (نبن), CP1L-M40DT1-D (بنب)
③ 60-point (36 المدخلات + 24 النواتج)
تكييف: CP1L-M60DR-A, CP1L-M60DT-A
العاصمة: CP1L-M60DR-D, CP1L-M60DT-D, CP1L-M60DT1-D
ثالثا. Ethernet Models (CP1L-EL / م, USB + إيثرنت)
1) CP1L-EL (5خطوات ك, economy with Ethernet)
20-نقطة (12 المدخلات + 8 النواتج)
CP1L-EL20DR-D, CP1L-EL20DT-D, CP1L-EL20DT1-D (DC24V only, no AC version)
2) CP1L-EM (10خطوات ك, standard with Ethernet)
① 30-point (18 المدخلات +12 النواتج)
CP1L-EM30DR-D, CP1L-EM30DT-D, CP1L-EM30DT1-D
② 40-point (24 المدخلات +16 النواتج)
CP1L-EM40DR-D, CP1L-EM40DT-D, CP1L-EM40DT1-D (Ethernet version corresponding to M40DT1-D)
③ 60-point (36 المدخلات +24 النواتج)
CP1L-EM60DR-D, CP1L-EM60DT-D, CP1L-EM60DT1-D
- CP1L Expansion Units (وحدات الإدخال/الإخراج, CPU excluded)
Input Units
CP1W-8ET, CP1W-16ET
Output Units
CP1W-8ER (تتابع), CP1W-8ET (نبن), CP1W-8ET1 (بنب)
CP1W-16ER, CP1W-16ET, CP1W-16ET1
Mixed I/O Units
CP1W-MAD11 (التناظرية), CP1W-20EDR1, CP1W-40EDR, CP1W-40EDT, CP1W-40EDT1
Communication Boards (side-mounted on CPU)
CP1W-CIF01: RS232
CP1W-CIF11: RS485 (مودبوس-RTU)
CP1W-CIF41: إيثرنت (for non-Ethernet CPU upgrade)
- ملخص الاختيار السريع
- Program capacity: L=5K steps; M=10K steps
- إيثرنت: No E = USB only; E = Built-in Ethernet
- Output polarity: DT=NPN sinking; DT1=PNP sourcing (common for European sensors)
- مزود الطاقة: -أ = تيار متردد 220 فولت; -D=DC24V
Application Fields of OMRON CP1L Series PLC
CP1L is a compact economy motion control PLC, equipped with onboard high-speed counters and pulse outputs. It supports analog, RS485/232 and Ethernet expansion. It is designed for standalone control of medium/small machines, suitable for simple stepper/servo positioning and Modbus communication. It is mainly for standalone الأتمتة and not recommended as main controller for large multi-station production lines.
- ماكينات التعبئة والتغليف (الأكثر شيوعًا)
آلات تعبئة وختم الشكل العمودي, horizontal flow wrappers, pouch packaging machines
ملصقات, آلات الحز, sealers, coding auxiliary controls
سمات: 2-axis pulse positioning, winding tension control, photoelectric counting, material detection. DT1 (بنب) widely used for imported sensors.
- نقل & Sorting Logistics Equipment
Small belt conveyors, roller lines, transfer machines, lifting & transfer units
Mini sorters, bin shuttles, مصاعد, stopper cylinder control
سمات: Multi-cylinder logic, photoelectric/proximity signal acquisition, inverter speed regulation via Modbus
- Custom Jigs & Special Automation Machines (Non-standard Automation)
Press-fit machines, riveting machines, test fixtures, automatic screw lockers
Automatic drilling, chamfering, grinding and assembly fixtures
سمات: Servo positioning, pressure acquisition (with analog modules), عملية التعشيق, safety door signal
- Food Processing Machinery
Dough mixers, slicers, آلات التعبئة, آلات السد, food forming machines
Cleaning machines, pasteurization auxiliary control cabinets
المزايا: RTC على مدار الساعة في الوقت الحقيقي, recipe storage, batch production logging
- ممحاة & بلاستيك, البثق & Cutting Equipment
Small extruders, rubber cutters, cutting presses, اللفافات
Fixed-length pipe cutting, fixed-length web cutting
الوظائف الرئيسية: High-speed counter for length measurement, pulse synchronization, cut-to-length stop
- امتحان & Inspection Equipment
Tensile testers, life test benches, airtightness testers
Continuity testers, withstanding voltage test fixtures, sensor calibration benches
Analog modules for pressure, displacement and voltage sampling
- النسيج & Printing Auxiliary Machines
Small fabric cutters, slitter-rewinders, simple printing tables
Label printers, الترجيع, auxiliary web guiding control
ملحوظة: High-speed main textile lines generally use CP1H or CJ series; CP1L is for auxiliary machines.
- التدفئة والتهوية وتكييف الهواء, معالجة المياه & Environmental Auxiliary Equipment
Small constant pressure water supply cabinets (pressure sampling via analog module)
Small chemical dosing units for wastewater, exhaust gas treatment auxiliaries, معجب & pump interlock
Suitable for limited I/O points and simple PID regulation
- Lithium & 3C Industry Small Fixtures
Electrode cutting, pole piece handling, inspection jigs, simple assembly machines
سمات: High demand for PNP output (DT1) to match Japanese/European sensors and servo drives
- Other General Machinery
Injection molding auxiliaries (الروبوتات, material dryers)
Woodworking machinery: panel cutting, grooving, small grinding equipment
Agricultural automation: automatic seeding, irrigation, sorting auxiliaries
Selection Guidelines — When to Choose CP1L
✅ موصى به: ≤2 axes servo/stepper positioning, total I/O ≤160 points, Modbus required, cost-sensitive standalone machines
❌ Not recommended: تزامن متعدد المحاور, large production lines, complex PID, high-precision high-speed motion control (choose CP1H or NX1P instead)
Frequently Used Matching Accessories
تواصل: CP1W-CIF11 (RS485 مودبوس) for inverters and temperature controllers
Motion: Pulse-type servo / stepper drives (EtherCAT not supported)
واجهة المستخدم البشرية: NB, NV series touch screens
