ABB 機械ドライブ ACS355-01E-02A4-2

ABB ACS355 series general machinery drive, 0.37 kW / 0.5 HP, single-phase 200–240 V input, IP20保護, rated output current 2.4 あ. Suitable for speed control and energy-saving operation of small machinery.

1 型式コードの説明

2 Key Technical Data

3 主な特長

3.1 柔軟な制御

Predefined application macros: 一定のトルク, ファン/ポンプ, PID制御, 等.

Local/remote control switching via keypad, terminals or fieldbus

Built-in PID controller for closed-loop flow, プレッシャー, 等.

3.2 信頼性の高い保護

過電流, 過負荷, 過電圧, 不足電圧, 過熱, 欠相保護

Motor over-temperature protection (requires external PTC)

Short-circuit and earth-fault protection

3.3 簡単操作

Compatible control panel with ACS350/510/550 series

Parameter copy function for fast commissioning

MTBF > 100,000 hours for continuous operation

4 代表的な用途

Small conveyors, 包装機械

ファン, パンプス (small HVAC systems)

ミキサー, centrifuges and small processing machines

Automatic doors, roller shutters

医療機器, 実験器具

Textile, printing and other light industrial machinery

5 インストール & Commissioning Guidelines

5.1 インストール要件

Must be installed in an enclosed electrical cabinet

周囲温度: 0–40℃ (derate 10% at 40–50°C)

垂直に取り付ける, keep ≥ 100 mm clearance above and below for cooling

Avoid dust, 油, 腐食性ガス

Input protection: 10 A MCCB (Cカーブ) or fuse recommended

5.2 Basic Commissioning Steps

1. Pre-power check: 配線を確認してください (L1/N input, U/V/W output), 端子トルク, proper earthing
2. パラメータの初期化

Group 99: set motor rated voltage, 現在, 力, スピード

Select application macro (標準, PID, 等)

3. Control configuration

Local control: via control panel

リモコン: via DI terminals or optional Modbus RTU

4. 動作テスト

無負荷試験: run at 5–10 Hz, check rotation and stability

負荷試験: gradually apply load, verify current and temperature

Adjust acceleration/deceleration time (1–10 s recommended)

6 Cross-Brand Replacement Options (0.37 kW, 1-段階 220 V, IP20)

7 選択 & メンテナンスのヒント

7.1 Recommended Options

Braking function: optional braking resistor (75 おお / 50 W recommended)

コミュニケーション: add RS485 module

Enhanced EMC: additional input EMC filter

7.2 メンテナンス

Clean cooling channels every 6 月

Check terminal torque annually

Avoid frequent starts/stops (≤ 20 times per day)

保管温度: -25°C ～ +60°C, dry environment

ABB ACS355-01E-02A4-2

Installation and Commissioning Manual

概要: This manual provides complete instructions for safety, インストール, 配線, parameter setting and commissioning of the ACS355-01E-02A4-2 drive (0.37 kW / 0.5 HP, single-phase 200–240 V) for general machinery speed control and energy saving.

1 Safety Instructions (必読)

1.1 電気の安全性

Power-off procedure: Disconnect all power before installation, wiring or maintenance. Wait 5 minutes for internal capacitors to discharge.

Earthing: PE terminal must be reliably earthed (earth resistance ≤ 4 おお)

過電流保護: インストール 10 A MCCB (Cカーブ) or fuse on input side

絶縁試験: Only test motor cables; do NOT apply voltage to the drive itself

1.2 Mechanical Safety

Rotating parts (shaft, カップリング, pulley) must be guarded

Mount vertically on solid surface to avoid vibration

Do not modify internal circuits or structures

1.3 Environmental Safety

動作温度: 0–40℃ (derate 10% at 40–50°C)

湿度: 5–95% RH, 結露しないこと

IP20: must be installed in enclosed cabinet

2 Product Overview and Model Identification

2.1 機種説明 (ACS355-01E-02A4-2)

2.2 コア仕様

3 Installation Procedure

3.1 準備

1. Unpack and inspect drive for damage
2. Choose well-ventilated, dust-free location inside cabinet
3. ツール: プラスドライバー (PH2), ワイヤーストリッパー, 圧着工具, マルチメータ, insulation tape

3.2 取り付け

1. Mount vertically on flat metal plate
2. Keep ≥ 100 mm above/below, ≥ 50 mm left/right clearance
3. Fix with M4 screws, 締め付けトルク: 1.2–1.5 N·m

4 Electrical Wiring

4.1 Terminal Description (ACS355-01E Series)

4.2 配線手順

1. Power wiring: L1/N to mains, PE to earth, U/V/W to motor
2. Control wiring (Standard macro example):

DI1: Forward (FWD), DI2: Reverse (REV), DI3: リセット

AI1: Speed reference (0–10 V)

3. Check torque, 絶縁, and phase sequence

5 パラメータ設定

5.1 Keypad Functions

▶/■: 始める / 停止

▲/▼: Adjust value

入力: Confirm

ESC: Back

LOC/REM: 地元 / リモート

5.2 Quick Motor Settings (Group 99)

5.3 Common Application Parameters

6 Commissioning Flow

6.1 Pre-Power Check

Correct power and control wiring

Motor and drive area clear

Cabinet ventilation OK

入力電圧: 200–240 V single-phase

6.2 最初のパワーアップ

Close MCCB, display shows REM or LOC

Check for fault codes

Verify Group 99 motor parameters

6.3 Motor Identification (オプション)

セット 9910 = 2 (ID Run)

Press ENTER; drive runs motor briefly

Completed when shown COMPLETE

6.4 No-Load Test

Switch to LOCAL

Run at 5 Hz, check rotation

Increase to rated frequency, check noise and vibration

6.5 負荷テスト

Switch to REMOTE

Control speed via AI1

Check output current ≤ 2.4 あ

Adjust acc/dec to avoid overcurrent

Test protection functions

7 トラブルシューティング

7.1 一般的な故障コード

7.2 Typical Issues

8 メンテナンス

8.1 定期的なメンテナンス

Clean cooling channels every 6 月

Check terminal torque annually

Log operating current and temperature

8.2 Long-Term Storage

温度: -25°C ～ +60°C

ドライ, ventilated environment

Power on for 1 hour every 6 月

9 Appendix: Options and Replacements

9.1 Recommended Options

制動抵抗器: 100 おお / 50 W

EMCフィルター

RS485 Modbus RTU module

Shielded cable for control wiring

9.2 クロスブランドの代替品 (0.37 kW, 1-段階 220 V, IP20)

Manual Version: V1.0 (based on ABB official ACS355 manual, adapted for ACS355-01E-02A4-2)

Effective Date: February 2026

Copyright: ABB Group, 無断転載を禁じます