OMRON E8EB-10C General-Purpose Pressure Sensor - コンタクタ,サーキットブレーカー,センサー,エンコーダ,PLC,コンバータ

微信: +86-13184948252 ワッツアップ: 0086-13811255435 電子メール: kent@bestcontactor.com

について 接触 |

OMRON E8EB-10C General-Purpose Pressure Sensor - コンタクタ,サーキットブレーカー,センサー,エンコーダ,PLC,コンバータ

PLC/

OMRON E8EB-10C General-Purpose Pressure Sensor

製品タイプ: Integrated Pressure Sensor (圧力スイッチ) | 状態: Discontinued by Manufacturer Omron E8EB series integrated pressure sensor with analog + switching output, positive pressure type, NPN出力. ✅ Core Specifications Pressure Range: 0~1 MPa (0~10 kgf/cm², 0~142 psi) 電源: DC24V Switch Output: NPNオープンコレクタ; マックス. 負荷電流 80 ミリアンペア, マックス. voltage DC30V ...

  • 製品詳細

製品タイプ: 統合された 圧力センサー (圧力スイッチ) | 状態: メーカー生産終了

オムロン E8EB series integrated pressure sensor with analog + switching output, positive pressure type, NPN出力.

✅ コア仕様

圧力範囲: 0~1 MPa (0~10 kgf/cm², 0~142 psi)

電源: DC24V

スイッチ出力: NPNオープンコレクタ; マックス. 負荷電流 80 ミリアンペア, マックス. voltage DC30V

Linear Analog Output: 1~5 V, Output impedance 20Ω, 分. load resistance 10 kΩ

応答時間: ≤5 ms

消費電流: 20 ミリアンペア

圧力ポート: ラジコン(PT)1/4

保護クラス: IP54

動作温度: -10℃~+55℃ (アイシングなし); ストレージ: -25℃~70℃

インジケータ: 赤色LED (lights up when output is ON)

ケーブル: 標準2mリード線

メディア: Dry air, 非腐食性ガス (Not suitable for corrosive liquid)

📌 Model Code Explanation (E8EB Series)

E8EB = Series Code

10 = Range 0~1MPa

C = NPN output; Suffix B = PNP (Model E8EB-10B)

01 = 0~0.1MPa; N0 = Vacuum type

🔁 Official Replacement Model: E8F2-B10C

アイテムE8EB-10C (旧モデル)E8F2-B10C (交換)
圧力範囲0~1MPa0~1MPa
出力NPNオープンコレクタ + 1~5V linear analogNPN, dual independent switch outputs + 1~5V linear analog
消費電流20ミリアンペア70ミリアンペア
負荷電流80ミリアンペア30ミリアンペア
調整Potentiometer adjustment, no digital displayデジタル表示 + 棒グラフ, one-touch teaching setup
取付寸法Different footprint and mounting holesCannot be plug-and-play; bracket and piping need modification

⚠️重要なお知らせ: Direct plug-in replacement is NOT feasible. 耐荷重, current draw and mounting dimensions differ; PLC wiring logic must be verified.

🧾 Pin Assignment (4-Core Cable)

茶色: DC24V+

青: 0V (GND)

白: ON/OFF Switch Output (NPN)

黒: 1~5V Linear Analog Output

🛠️ Troubleshooting Checklist

  1. 出力なし: Check 24V supply and blue wire ground; confirm pressure exceeds set threshold
  2. Abnormal analog signal: Load resistance ≥10kΩ; low-resistance loads are prohibited
  3. LEDが点灯しない: Pressure not reaching actuation point, or incorrect hysteresis setting
  4. Signal drift: Water/oil contamination in air source, out-of-range temperature, or pressure surge exceeding full scale

📎 Supplementary Information

使用済み / second-hand units are still available on the aftermarket; no brand-new original stock

HSコードリファレンス: 90262090 (Gas pressure measuring sensor)

代替モデル: E8F2 series, E8CC series digital pressure sensors

E8EB-10C → E8F2-B10C Retrofit Wiring List (4-core old → 5-core new)

E8EB: 4-コア; E8F2-B10C: 5-コア (dual switch outputs + 1~5V analog), NPN, 0~1MPa, DC24V

Goal: Retain the original circuit: 1 switch signal + 1~5V analog; leave the second output unused and insulated.

  1. Wire Color Matching Table
E8EB-10C (古い, 4-コア)関数E8F2-B10C (新しい, 5-コア)関数Connection Plan
茶色DC24V+茶色DC24V+✅ Direct connection
青0VGND青0VGND✅ Direct connection
白Switch Output OUT1 (NPN)白 (OUT1)スイッチ出力 1 (NPN)✅ Connect to original PLC input point (keep original pressure signal logic)
黒1~5V Analog Signalグレー1~5V Analog Output✅ Original black wire → new grey wire
—N/A白 (OUT2)Independent Switch Output 2 (NPN)⚠️ Leave unused, wrap with insulation; short-circuit strictly forbidden

重要なリマインダー: The analog output on E8F2 is the grey wire NOT the white wire, this is the most common wiring mistake. If analog signal is not required, insulate the grey wire separately.

  1. 配線手順
  2. Cut off all power; confirm PLC and sensor power circuits are fully de-energized
  3. Disconnect old sensor terminals and record Brown/Blue/White/Black channel mapping
  4. 電源回路: Brown to Brown, Blue to Blue (DC24V電源)
  5. Switch signal: Original white wire → E8F2 OUT1 white wire (match original PLC logic)
  6. Analog signal: Original black (1~5V) → E8F2 grey wire
  7. E8F2 OUT2 white wire: Seal with heat-shrink tube/insulation tape, keep isolated
  8. Inspect wiring for short circuits and exposed copper before powering on.
  9. Parameter Differences & PLC Program Verification Checklist (必須)
アイテムE8EB-10CE8F2-B10CRetrofit Risk Point
Current Draw20ミリアンペア70ミリアンペアRecheck 24V power supply capacity; insufficient margin will cause voltage drop
Switch Load Capacity80ミリアンペア30ミリアンペアPLC digital input is fine; if the original circuit drives a relay directly, the relay cannot be reused; 負荷電流を減らす
Thread Portラジコン(PT)1/4R(PT)1/8Must install reducing adapter; cannot thread directly
取り付けOriginal bracket28mm panel / E89-F3 bracketHole positions do not match; new holes or adapter plate required
設定方法Potentiometer adjustmentメニュー / teaching setupPressure setpoints and hysteresis must be reconfigured; old potentiometer values are invalid
Output ChannelsSingle switchTwo independent switchesProgram only uses OUT1; disable OUT2
  1. Power-On Commissioning Sequence
  2. No-load power-on first; confirm E8F2 digital display lights up normally
  3. Enter menu: Set actuation mode, pressure setpoint and hysteresis to match the original E8EB values
  4. Pressurize and test: Verify OUT1 triggers PLC input correctly
  5. Analog test: 0MPa ≈1V, 1MPa≈5V; confirm linear reading on PLC analog channel
  6. Stabilize signal: Enable anti-chatter filter to prevent false triggering caused by air pressure fluctuation.
  7. クイックトラブルシューティング

No analog reading: Grey wire disconnected or misconnected to OUT2 white wire

Cannot drive load: Load current exceeds 30mA rating

No switching action: Parameters not reconfigured; factory default values differ from old sensor

空気漏れ: Thread mismatch; missing reducing adapter

Full Commissioning Procedure: E8EB-10C Upgrade to E8F2-B10C (Match Original System Logic)

客観的: OUT1 replaces the old E8EB switch point; grey wire 1~5V analog keeps the original PLC analog channel; OUT2 remains unused.

ボタン: セット (Confirm/Enter), Up ▲, Down ▼; Press and hold SET for 2s to enter main menu; short press SET for pressure setting.

ステップ 1: 電源前チェック (Prevent PLC Input Burnout)

  1. 配線を確認してください: 茶色=24V+, 青=0V, White=OUT1, Grey=Analog, OUT2 white wire fully insulated
  2. Load check: E8F2 NPN output max. 30ミリアンペア. Do not drive relays directly. Add an intermediate relay if the old circuit had a relay load
  3. 配管: Install PT1/8 to PT1/4 reducing adapter with thread sealant; test for air leakage before commissioning
  4. Air source: Use dry compressed air free of excessive water and oil; working pressure cannot exceed 1MPa full scale
  5. PLC側: Analog input impedance ≥10kΩ; low-resistance loads are prohibited.

ステップ 2: No-Load Power On & ゼロリセット (Zero Pressure Condition)

  1. Power the sensor alone, without air pressure applied, wait for display stabilization
  2. Zero point reset (zero pressure calibration): Press ▲+▼ simultaneously to reset zero reading

注記: Zero reset must be done at zero pressure; calibration under pressure will lead to permanent drift.

ステップ 3: Basic Parameter Setup (Hold SET 2s to enter main menu)

  1. ユニット (unt): Select MPa (consistent with old sensor; kPa is also acceptable)
  2. 動作モード (m-a): Select HYS (Hysteresis Mode, same as E8EB); avoid Window Mode
  3. 出力ロジック (ope): NPN, 通常開 (いいえ); output ON when pressure exceeds set value
  4. Anti-chatter Filter: Set to STND (標準); select longer filtering if air pulsation is severe to avoid signal chattering
  5. 保存: Hold SET 2s to return to measurement screen.

Only configure OUT1; leave OUT2 parameters unchanged as it remains unused.

ステップ 4: Pressure Setpoint Configuration (2 オプション: Manual Input / Teaching Mode; Teaching is Recommended)

オプションA: 2-ポイントティーチング (Best for replicating old E8EB trigger points)

  1. Short press SET to enter pressure setting → select OUT1 → select 2-point teaching
  2. Slowly raise pressure to ON actuation pressure, stabilize and press SET to save the ON point
  3. Slowly reduce pressure to OFF release pressure, stabilize and press SET to save hysteresis OFF point
  4. Hold SET to save and exit.

例: Original E8EB turns ON at 0.5MPa and OFF at 0.4MPa; teach these two pressure values directly on site.

オプション B: Manual Value Entry (If original setpoints are known)

  1. Short press SET → enter OUT1 ON value → adjust value with ▲▼
  2. Press SET to switch to OUT1 OFF value → set hysteresis (オフ < の上)
  3. Press SET again to jump to OUT2; skip without modification
  4. Hold SET to save and exit.

Recommended hysteresis: Keep consistent with original setting to avoid frequent cycling; factory default hysteresis = 3%FS (30kPa for 0~1MPa range).

ステップ 5: Switch Output Test (OUT1, PLC Digital Input)

  1. Gradually increase pressure; check E8F2 OUT1 indicator + PLC input: ON when pressure ≥ setpoint
  2. Gradually reduce pressure; input turns OFF when pressure drops below OFF threshold
  3. Repeat 3 times to confirm:

No flickering or intermittent signal

Trigger action fully consistent with the old sensor

No premature or delayed switching

トラブルシューティング: Frequent chattering → increase filter time and hysteresis; no action → reverse NO/NC output logic.

ステップ 6: 1~5V Analog Channel Calibration (Grey Wire, クリティカルステップ)

範囲: 0~1MPa = 1V ~ 5V

0MPa: Theoretical output ≈1.0V

0.5MPa: Theoretical output ≈3.0V

1.0MPa: Theoretical output ≈5.0V

試運転手順:

  1. Zero pressure: Confirm PLC analog reading ≈1V
  2. Pressurize to 0.5MPa and cross-check reading
  3. Full scale 1MPa: Verify output ≈5.0V

⚠️重要な注意事項: E8F2 analog output is pre-calibrated for linearity. No re-calibration on PLC side is required. If deviation occurs, redo zero reset first and check load resistance.

ステップ 7: Full System On-Line Test (Automatic Machine Cycle)

  1. Switch equipment to automatic mode; verify pressure interlock and alarm logic work correctly
  2. Run continuously for 5~10 minutes; confirm output stays stable under pressure fluctuation
  3. Record actuation pressure, hysteresis and filter parameters in engineering change records
  4. Add pressure buffer/throttle on the air inlet if pressure surge occurs to prevent overpressure damage.

ステップ 8: 障害トラブルシューティング表

症状根本的な原因救済策
OUT1 never switches ONON setpoint too high; NO/NC logic reversedRecheck set value; modify ope output mode
Switch signal flickers continuouslyAir source pulsation; 濾過時間が短すぎるExtend response filter; increase hysteresis value
Analog signal stuck fixed at 1VGrey wire broken/disconnected; load resistance too lowInspect grey wire; ensure PLC input resistance ≥10kΩ
Zero reading drifts constantlyZero reset performed under pressure; air contains water/oilRe-zero at zero pressure; install air filter for moisture removal
Output stays permanently ON after power-upOFF value set higher than ON value (parameter reversed)Ensure OFF pressure < ON pressure
PLC input channel burned outLoad current exceeds 30mA ratingRemove direct relay drive; 中間リレーを追加する

Full Model List of OMRON General-Purpose Gas Pressure Sensors (Pneumatic / コンプレッサー / 真空, Dry Air Only)

注記: All models are Gauge Pressure. 出力: NPN/PNP switch + 1~5V analog. Split into Discontinued Legacy Models + Official Replacement Models, suitable for spare part replacement, BOM & foreign trade.

サフィックスの定義: C=NPN; B=PNP; A01=0~100kPa; B10=0~1MPa; AN0=Vacuum 0~-101kPa.

  1. E8EB Series (表示なし, ポテンショメータの調整, 製造中止)

4-core lead wire, RC1/4 thread, シングルスイッチ + 1~5V analog; 20mA current draw, 最大. load 80mA.

モデル圧力範囲出力
E8EB-01C0~100kPa (0.1MPa)NPN
E8EB-01B0~100kPa (0.1MPa)PNP
E8EB-10C0~1MPaNPN (Main Model in This Retrofit)
E8EB-10B0~1MPaPNP
E8EB-N0C2B0~-100kPa VacuumNPN
E8EB-N0B2B0~-100kPa VacuumPNP
  1. E8F2 Series (デジタル表示, official replacement for E8EB/E8CC, 製造中止)

5-コアケーブル, PT1/8 thread, dual independent switch outputs + 1~5V analog; 70mA power consumption; single channel max. load 30mA; one-touch teaching programming.

モデル圧力範囲出力
E8F2-A01C0~100kPaNPN (E8EB-01C Replacement)
E8F2-A01B0~100kPaPNP
E8F2-B10C0~1MPaNPN (Direct replacement for E8EB-10C)
E8F2-B10B0~1MPaPNP
E8F2-AN0C0~-101kPa VacuumNPN
E8F2-AN0B0~-101kPa VacuumPNP
  1. E8CC Series (Slim digital type, predecessor of E8EB, 製造中止)

With digital display, シングルスイッチ + 1~5V analog; DINレール取付; replaced by E8F2.

モデル圧力範囲出力
E8CC-A01C0~100kPaNPN
E8CC-B10C0~1MPaNPN
E8CC-AN0C0~-101kPa VacuumNPN
  1. E8MS / E8M Split Type (Sensor Head + コントローラ, 製造中止)

Pure 1~5V analog signal without built-in switch; requires E8M controller for multi-channel pressure acquisition.

モデル圧力範囲タイプ
E8MS-010~100kPaPositive Pressure Probe
E8MS-100~1MPaPositive Pressure Probe
E8MS-N00~-101kPa VacuumVacuum Probe
E8MS-N1-101~101kPa Compound PressureCompound Pressure Transducer
E8M-100~1MPaE8M Independent Probe
E8M-N00~-101kPa VacuumVacuum Probe
E8M-A10~1000PaMicro Differential Pressure
  1. E8AA Series (Stainless Steel Diaphragm Special Model, 製造中止)

Limited use for liquid / slightly corrosive gas applications.

モデル圧力範囲
E8AA-M050~500kPa
E8AA-M100~1MPa
  1. E8Y / E8Y-L Micro-Pressure Sensors (Differential Pressure for Duct & ファン, Not General Pneumatic Type)

Pa-level low pressure (200Pa ~5kPa); some models with 4-20mA output; used for air duct and filter differential pressure monitoring only.

✅ Cross Reference Table (Spare Part Replacement Priority)

旧モデル推奨代替品主な違い
E8EB-01CE8F2-A01CPT1/8 thread, dual outputs, load current reduced to 30mA
E8EB-10CE8F2-B10CFull retrofit plan covered above
E8EB-N0C2BE8F2-AN0CVacuum pressure type
E8CC-A01CE8F2-A01CDifferent mounting footprint

📌 General Notes

  1. メディア: Dry non-corrosive air; Not for liquid or strong corrosive gas
  2. Analog Output Standard: 1~5V (1V at zero pressure, 5V at full scale)
  3. Thread Spec: E8EB = RC1/4; E8F2 = R1/8; reducing adapter is mandatory for retrofit
  4. 電源: DC24V
  5. All listed models are discontinued; 余剰在庫のみ & 中古ユニットも入手可能. New projects shall select the latest OMRON E8F series.

前へ:

返信を残す

伝言を残す