シュナイダー LRD340C サーマル過負荷リレー - コンタクタ,サーキットブレーカー,センサー,エンコーダ,PLC,コンバータ

微信: +86-13184948252 ワッツアップ: 0086-13811255435 電子メール: kent@bestcontactor.com

について 接触 |

シュナイダー LRD340C サーマル過負荷リレー - コンタクタ,サーキットブレーカー,センサー,エンコーダ,PLC,コンバータ

電気/

シュナイダー LRD340C サーマル過負荷リレー

TeSys Deca Thermal Overload Relay, Motor Overload Protection Core Parameters Current setting range: 30 … 40 A Trip Class: 10あ (Class10A) IECに準拠 60947-4-1 定格動作電圧 (主回路): 690V AC Auxiliary contacts: 1いいえ + 1ノースカロライナ州 (97-98 いいえ / 95-96 ノースカロライナ州) 端子: EverLink BTR screw terminals Compatible contactors: LC1D40A / LC1D50A / LC1D65A (新しい ...

  • 製品詳細

テシスデカ サーマルリレー, モーター過負荷保護

コアパラメータ

電流設定範囲: 30 … 40 あ

旅行クラス: 10あ (Class10A) IECに準拠 60947-4-1

定格動作電圧 (主回路): 690Vと

補助 連絡先: 1いいえ + 1ノースカロライナ州 (97-98 いいえ / 95-96 ノースカロライナ州)

端子: EverLink BTR screw terminals

Compatible contactors: LC1D40A / LC1D50A / LC1D65A (New TeSys Deca contactors with suffix A)

Operating buttons: Blue RESET button, red STOP test button

Ambient temperature compensation: -20 ~ +60℃

保護クラス: IP20

全体の寸法: 70(H) × 55(W) × 123(D) mm, 正味重量: 0.375 kg

Tightening Torque for Wiring

主回路端子: 5 N・m

Auxiliary circuit terminals: 1.7 N・m

接点の定格 (制御回路)

AC-15 / 380V: 0.95あ

DC-13 / 440V: 0.06あ

モデルの定義

LRD: TeSys Deca thermal overload relay series

340: Current code (30–40A)

C: 国内版 (standard model for local market)

交換 & Compatibility Notice

  1. Old equivalent model: LRD3355C (old TeSys D series for LC1D40/50/65 without suffix A). The plug-in base is different and they cannot be directly interchanged.
  2. Differential phase-failure version in the same current range: LRD3403C (with differential phase loss protection).
  3. Adjacent models in the same series: LRD332C (23-32A), LRD365C (48-65A).

代表的な用途

Overload protection for three-phase asynchronous motors. It can be directly plugged under LC1D40A~D65A contactors to form a magnetic starter, with manual reset function.

トラブルシューティングガイド

頻繁なトリップ: Verify that the motor rated current falls within 30–40A; check for phase loss, motor stalling or poor heat dissipation.

トリップ失敗: Check if the setting knob is adjusted too high or the relay is aged due to long-term high temperature.

No continuity on auxiliary contacts: 95/96 is normally closed and opens after overload; 97/98 is normally open and closes after overload.

Schneider TeSys Deca LRD Thermal Relay + LC1D (New A-Suffix Contactor) Plug-in Selection List

重要な注意事項: LC1DxxA (New EverLink terminals → matched with LRDxxC); LC1Dxx (Old version without A → matched with LRD33xxC). Bases are NOT interchangeable.

全モデル: トリップクラス 10A, 1NO+1NC補助接点, -20~+60℃ temperature compensation, 690V, IP20

Thermal Relay Model設定電流 (あ)Directly Plugged Contactor
LRD01C0.10–0.16LC1D09A / D12A / D18A / D25A / D32A / D38A
LRD02C0.16–0.25LC1D09A~D38A
LRD03C0.25–0.40LC1D09A~D38A
LRD04C0.40–0.63LC1D09A~D38A
LRD05C0.63–1.00LC1D09A~D38A
LRD06C1.00–1.60LC1D09A~D38A
LRD07C1.60–2.50LC1D09A~D38A
LRD08C2.50–4.00LC1D09A~D38A
LRD10C4.00–6.00LC1D09A~D38A
LRD12C5.50–8.00LC1D09A~D38A
LRD14C7.00–10.0LC1D09A~D38A
LRD16C9.00–13.0LC1D09A~D38A
LRD21C12.0–18.0LC1D18A~D38A
LRD22C16.0–24.0LC1D25A~D38A
LRD313C9.0–13.0LC1D40A / D50A / D65A
LRD318C12.0–18.0LC1D40A / D50A / D65A
LRD325C17.0–25.0LC1D40A / D50A / D65A
LRD332C23.0–32.0LC1D40A / D50A / D65A
LRD340C30.0–40.0LC1D40A / D50A / D65A
LRD350C37.0–50.0LC1D40A / D50A / D65A
LRD365C48.0–65.0LC1D50A / D65A
LRD380C62.0–80.0LC1D80A

相互参照: Old Non-A Contactors (LC1D40/D50/D65)

設定電流Old Relay (for LC1D40/50/65)新しい交換品 (for LC1D40A/50A/65A)
30–40ALRD3355CLRD340C
23-32ALRD3353CLRD332C
37–50ALRD3357CLRD350C
48-65ALRD3359CLRD365C

Higher Current Models: LRD4xxx / LR9D (Separate Mounting, No Direct Plug-in)

LRD480C: 51–81A, fits LC1D80A / D95A / D115A with adapter bracket

LRD4365C: 80–104A, fits LC1D115A

LR9D series: Electronic relays for motors above 110A, DIN rail independent mounting

Coil Voltage Suffix (LC1D Contactors)

M7C: 220AC50/60Hz (Most common domestic model)

Q7C: 380Vと

B7C: 24Vと

CC7C: 36Vと

F7C: 110Vと

BD: 24ワシントンDCで

Full model example: LC1D40AM7C + LRD340C

選択ルール

  1. Relay setting current = motor rated current; keep rated current in the upper-middle part of the setting range.
  2. Star-Delta starting: If the relay is installed on the star point circuit, set current = motor rated current × 0.58; set to rated current if fitted on main circuit.
  3. Phase-loss protected version: サフィックス 3 → LRD3403C (30–40A with differential phase failure protection).
  4. Non-plug-in installation: DIN rail mounting without contactor, using accessory base.

Accessory List for LRD3xxC Series

LAD7B1: DINレール取付ベース (separate installation away from contactor)

LAD9: Connection links

LADR: Remote reset accessory

Working Principle of Schneider LRD (テシスデカ) Bimetallic Thermal Overload Relay

基本原則: Thermal effect of current + differential thermal deformation of bimetallic strip, inverse-time overload protection. The relay itself cannot break the main circuit directly.

  1. 内部構造

各相には発熱体が取り付けられています (抵抗線) プラスバイメタルストリップ (熱膨張係数の異なる 2 つの金属層を貼り合わせたもの). 機械的リンケージも含まれます, 1NO+1NC補助接点, 設定ノブ, 温度補償ストリップとリセット機構.

  1. 通常動作

モーターの定格電流が発熱体に流れ、温度上昇が最小限に抑えられます。; バイメタルストリップはトリップ機構を作動させることなくわずかに曲がるだけです.

95-96 NC接点は閉じたままです (コンタクタコイル回路に配線)

97-98 NO接点が開いたままになります (故障警報)

コンタクタは閉じたままとなり、モーターは継続的に動作します。.

  1. 過負荷動作 (コアアクション)

継続的な過負荷 → より高い電流 → 発熱体の継続的な加熱.

バイメタルストリップの 2 つの層が不均一に膨張します, 低膨張側への曲がり.

過負荷倍数が高いほど、加熱とトリップが速くなります。 (逆時間特性, Class10A: 10倍の過負荷下で10秒以内にトリップ), モーターの温度上昇曲線と一致.

曲げが閾値に達したとき, リンケージは接点を反転します:

95-96 NC が開きます → コンタクタのコイルが非通電になります, 主接点が開き、モーターが停止します

97-98 NO が閉じる → 表示灯または PLC アラーム信号がトリガーされます

キーポイント: サーマルリレーは制御回路を遮断するだけです. コンタクタが大電流主回路を遮断する.

  1. 欠相保護 (LRD3403C デフモデル)

3本のバイメタルストリップが差動機構と連動. 1 つの相が電力を失った場合, 不均一な加熱により曲げの違いが増幅される, 単相運転によるモーターの焼損を防ぐ高速トリップを可能にします。.

  1. 周囲温度補償

内蔵の補償バイメタルストリップにより、周囲温度の変化によって引き起こされる誤ったトリップを排除します。, -20℃から+60℃まで安定した保護電流を維持.

  1. リセット動作

トリップにはバイメタルストリップの冷却時間が必要です. LRD のデフォルト設定は手動リセットです (青色のRESETボタン); 一部のモデルは自動リセット切り替えをサポートしています.

主な違い (よくある落とし穴)

LRD: メカニカルバイメタルリレー, 長期にわたる過負荷保護のために設計されています. 熱慣性があるため、短絡保護を提供できません (回路ブレーカーまたはヒューズによって短絡保護を実装する必要があります).

LR9D: 変流器サンプリング機能付き電子過負荷リレー + MCUの計算. より高い精度を実現します, 通信をサポートし、より高速な欠相保護を提供します.

モーター電流によりバイメタルストリップが加熱されます; 熱曲げにより接点が切り替わる, コンタクタ制御ループの切断. モーターの温度上昇をシミュレートし、信頼性の高い過負荷保護を提供します。.

Schneider TeSys サーマル過負荷リレーの完全な選択ガイド

利用可能なシリーズ: LRD (メカニカルバイメタル, テシスデカ), LR9D/LR9F (電子), LRE (エコノミー範囲)

意味: Thermal relays only provide overload protection, NOT short-circuit protection (short-circuit protection is handled by MCBs or fuses). They cannot break the main circuit directly; they stop the motor by opening the contactor coil circuit.

ステップ 1: Collect Motor Nameplate Data (必須)

Take the motor rated current Ie printed on the nameplate as the primary reference; never select purely by power rating (current varies greatly with pole count for the same power).

Required data:

  1. 3-段階 / 単相, 定格電圧 (380V/400V/220V)
  2. Full-load current (フロリダ州 / つまり)
  3. Starting mode: ダイレクトオンライン / Star-Delta / Auto-transformer / VFD
  4. 負荷の種類: ファン & ポンプ, crusher, コンベア, コンプレッサー, frequent start-stop
  5. 環境: 周囲温度, cabinet ventilation, 高度, ほこり & 高温
  6. 保護要件: Fast phase-loss protection, プレアラーム, コミュニケーション, adjustable trip class

ステップ 2: Current Setting Rules

The relay’s current range must fully cover the motor rated current, preferably placing FLA in the upper-middle section of the range.

標準任務 (ファン, パンプス, continuous running): 設定電流=モータFLA×1.00~1.05

重負荷 / 開始時間が長い (破砕機, スクリューコンプレッサー): 1.05~1.15

頻繁な発停 & 衝撃荷重: 1.10~1.15

キャビネット温度が高い, 換気が悪い, 小型モーター, 熱に弱い機器: 0.90~0.95

スペシャルスターデルタスタート: スターポイント回路に取り付けた場合 → 設定電流 = モーター FLA × 0.58; 主回路に取り付けられている場合は FLA に設定.

例: モーター定格電流 30A → LRD340C を選択 (30–40A), ノブを30Aに設定します.

ステップ 3: 旅行クラス (IEC 60947-4-1)

Class10A (LRDのデフォルト): 10倍の過負荷下で10秒以内にトリップ. ほとんどの三相モーターの標準, ファンとポンプ.

クラス5: ショートスタート用の高速トリップ, 熱に弱いモーター.

クラス20: ロングスタート高耐久モーター (始動時間付きの大型慣性ファン >10s).

クラス30: 非常に長時間起動するアプリケーション (大型遠心ファン).

注記: LRDメカニカルリレーは固定Class10Aです (調整不可); LR9D 電子リレーは切り替え可能なクラスをサポート 5/10/20/30 DIPスイッチ経由.

シリーズ比較 (主要な選択基準)

シリーズ動作原理電流範囲欠相保護
LRD (テシスデカ, サフィックスC)バイメタルメカニカル0.1~80A; LRD4 最大 104A標準バージョン: 過電流時のみ低速トリップ; サフィックス 3 (LRDxx3C): Differential fast phase loss
LR9D ElectronicCT sampling + microcontroller0.1~150AFast differential phase loss (trips within ~4s)
LR9F Electronic電子150~630AFast differential phase loss
LRE (Economy Easy range)機械式124–198ABasic phase-loss protection

Important Warning: Ordinary LRD without differential design trips very slowly after phase loss, leading to easy motor burnout. Choose LR9D or LRDxx3C differential models for phase-loss sensitive applications.

インストール & コンタクタのマッチング (Frequent Mistakes)

  1. LRD Plug-in Compatibility Rule

New contactor LC1DxxA (EverLink terminals with A suffix) → LRDxxC (テシスデカ)

Old contactor LC1Dxx (No A suffix, old TeSys D) → Old LRD33xxC. Bases are NOT interchangeable.

例: Old LC1D40 → LRD3355C; New LC1D40A → LRD340C.

  1. Two Mounting Methods
  2. Direct plug-in (推奨): Snap the relay directly under the contactor, saving wiring space; available for 0.1–80A standard models.
  3. Separate DIN rail mounting: リレーを DIN レールに独立して取り付けるには、LAD7B1 ベースを使用します, コンタクタから分離; 大電流モデルに最適, キャビネットレイアウトの制約と改造プロジェクト.
  4. 標準補助接点の定義 (全シリーズ)

95–96: NC接点, コンタクタコイル回路に配線; 過負荷後に開いてモーターを停止します (主保護回路).

97–98: 連絡なし, 過負荷後に閉じて表示灯または PLC 障害信号を駆動します.

接点容量: AC-15 380V: 0.95あ; DC-13 440V: 0.06あ. 制御信号のみ; 高電力負荷を接続しないでください.

モデルの命名の内訳 (LRDメインシリーズ)

LRD340C / LRD3403Cの例

LRD: TeSys Deca 機械式サーマル過負荷リレー

340: 現在の仕様コード (30–40A)

3: 差動欠相保護 (LRD3403C); 数字なし = 標準バージョン

C: 国内市場標準バージョン

LR9Dの例: LR9D536

LR9D: 電子サーマルリレー

536: 現在の仕様コード

特別なアプリケーションの選択ルール

  1. VFD駆動モーター: インバーターには電子熱モデルがすでに組み込まれています; 通常は追加のサーマルリレーは必要ありません. リレーを取り付ける必要がある場合, LR9D電子リレーのみを選択してください. Bimetallic LRD will suffer frequent false tripping caused by harmonic distortion.
  2. 単相モーター: Choose LR9D with single-phase detection. Ordinary 3-phase LRD will lose accuracy on single-phase circuits.
  3. Multiple motors on one feeder: Never share one relay for multiple motors. One thermal relay per individual motor.
  4. 高地 / 高温: For ambient temperature >+60℃, derate the relay and prefer LR9D electronic type. LRD has built-in compensation only for -20~+60℃; adjust setting current beyond this range.
  5. Explosion-proof locations: Use certified explosion-proof models. Standard LRD/LR9D cannot be fitted inside flameproof enclosures directly.

LRD Series Accessory List

LAD7B1: DIN rail independent mounting base

LADR: External remote reset accessory (cabinet door operation)

LAD9: Interconnection links

透明保護カバー: Prevent accidental adjustment of the setting knob

Final Selection Checklist

電流設定範囲はモータ定格 FLA を完全にカバー

コンタクタとリレープラグインベースの一致 (LC1DxxA ↔ LRDxxC)

トリップクラスはモーターの始動時間と一致します

欠相保護グレードが負荷臨界を満たす (標準LRD / LRDxx3C / LR9D)

周囲温度が定格範囲内にとどまる; 過熱した場合は出力を下げる

PLCに合わせた補助接点容量 / インジケーターのロード

短絡保護 (D カーブ MCB またはヒューズ) 上流に設置されている

応用例 (380V DOL 開始)

場合 1: 30kW 400V 三相モーター, FLA≈56A, ウォーターポンプ, ダイレクトスタート, 単相焼損の危険性が高い

解決:

コンタクタ: LC1D65AM7C

リレー: LR9D電子リレー (高速欠相保護, カバー56A)

クリティカルでない負荷に対する代替予算: LRD365C (48欠相応答が遅い –65A メカニカルリレー)

場合 2: 15FLA=30AのkWモーター, 普通のファン, 良好なキャビネット冷却, コスト優先

コンタクタ: LC1D40AM7C

リレー: LRD340C (30–40A, Class10A)

よくある選択の間違い

  1. ❌ 銘板 FLA を確認せずに、純粋にモーター出力で選択します。 (2極と4極では電流が大きく異なります).
  2. ❌ 短絡保護のためにサーマルリレーを使用し、上流の回路ブレーカーを取り外します.
  3. ❌ 新旧のコンタクタとリレーの組み合わせを混在させる (A のない LC1D は LRDxxC の新しいベースに接続できません, 接触不良の原因になる).
  4. ❌ 機械式 LRD を VFD 出力端子に取り付ける; 高調波により連続的な誤トリップが発生する.

5. ❌ リレーの位置が間違っている & スターデルタスターターの設定要素 (掛けるのを忘れる 0.58 スターサーキット上で, 保護に失敗する

前へ:

返信を残す

伝言を残す