SMC IP8000 電空バルブポジショナ

The IP8000 is a classic SMC mechanical E/P electro-pneumatic positioner (non-smart, no HART). It is designed for linear-stroke pneumatic diaphragm actuators. It receives a 4~20mA current signal and converts it into supply air pressure to drive コントロールバルブ. It replaces the older IP6000 series. The IP8100 in the same series is for rotary-stroke applications. The IP8001/IP8101 are smart versions with auto-tuning and share the same housing.

✅ Key Technical Specifications

📌 Model Code Definition (IP8000-□□□)

IP8000: Lever-type mechanical electro-pneumatic positioner

1. Pressure gauge specification: 0=0.3MPa, 3=1.0MPa
2. 工事: Standard housing / ExdⅡBT5 explosion-proof terminal box
3. 付属品: Restrictor pilot valve, yoke linkage, extended feedback lever, 等.
4. Thread type, CE marking, special custom codes (例えば. X310=IP66)

🛠 Working Principle & 設置ガイドライン

1. 原理: A 4~20mA current energizes the torque motor. The nozzle-flapper amplifies the signal to control the output air pressure of the pilot valve. The feedback lever captures the actual valve stem position to form a closed loop, ensuring valve position matches the input signal.
2. Key Installation Rule: で 50% 信号 (12ミリアンペア), the feedback lever should form a 90° right angle with the valve stem. Select the internal feedback spring according to single-acting or double-acting actuators.
3. 調整: Mechanical Zero and Span knobs. Supports split range operation. Equipped with manual/auto switching screw for manual air supply during commissioning.

⚠️ Common Troubleshooting

1. Valve fails to move

No supply air or insufficient air pressure; 4~20mA wiring reversed; nozzle/restrictor blocked by dust; torque motor damaged.

2. Oscillation / 狩猟

Incorrect feedback lever mounting angle; unstable supply air pressure; stuck pilot valve; excessive friction of valve packing.

3. Poor linearity / Zero drift

Zero/span not calibrated; loose feedback linkage; air piping leakage; large ambient temperature variation.

4. Insufficient output pressure

Foreign matter jamming pilot valve; leaking actuator diaphragm/cylinder; clogged air filter.

Maintenance Reminder: Cut off air supply and fully vent pressure before disassembly. Clean nozzle orifice with a 0.2mm fine wire. Apply TORAY SH45 silicone grease lightly when assembling O-rings.

📋 Model Selection & 代替案

IP8000: 機械式, linear stroke lever. For conventional control valves, 低コスト, 連絡がありません.

IP8100: 機械式, rotary cam, for butterfly and ball valves.

IP8001: Smart linear stroke. Auto-calibration, ハート, 故障診断, upgrade replacement for IP8000.

国内代替品: Domestic E/P positioners such as Wuzhong and Chuanyi. Verify bracket, air port and stroke matching.

📎 Typical Application Scenarios

Continuous regulation of flow, pressure and level on linear pneumatic diaphragm control valves in chemical, 水処理, 空調設備, 紙, 油 & gas pipelines. Explosion-proof versions ExdⅡBT5 are available for hazardous areas.

SMC IP8000 Electro-Pneumatic Valve Positioner — Application Scenarios

The IP8000 is a linear-stroke mechanical E/P positioner matching diaphragm linear pneumatic control valves. It converts 4~20mA analog signal into air pressure to drive valve stem for continuous process regulation. No HART communication.

🏭 Industry Applications

1. 水 / 廃水処理

Inlet flow regulation, pH dosing line, 液面制御, aeration pressure regulation. Standard non-explosion model is sufficient; IP65 preferred for outdoor installation.

2. 空調設備 & Heating Networks

Temperature control for primary/secondary side of heat exchangers, regulating steam/hot water linear control valves.

3. Paper Industry

Pulp concentration control, white water flow, steam pressure regulation. Dust-prone workshop; air filtration is mandatory to prevent nozzle blockage.

4. 化学工業 (Use ExdⅡBT5 explosion-proof IP8000 for hazardous zones)

Continuous regulation of flow, pressure and level in process pipelines. Explosion-proof housing required for solvents and light hydrocarbon hazardous areas.

注記: IP8000 is mechanical without smart diagnosis. Use IP8001 if HART and auto-tuning are required.

5. 食べ物 & 飲料 / 医薬品 (Sanitary Service)

精製水, wash water and steam regulation, paired with sanitary linear control valves. Prefer clean instrument air.

6. 力 & 火力発電所

Boiler feedwater, desuperheating and pressure reduction, condensate level control; auxiliary process control valves.

7. 油 & Gas Storage & 交通機関 (Explosion-proof Version)

Pressure and flow regulation for crude/product pipelines, tank level control. Exd explosion-proof model for explosive hazardous areas.

✅ Suitable Valve Types

Single-acting / double-acting linear pneumatic diaphragm control valves (best match)

Cage guided valves, single-seat valves, cage control valves

❗ Butterfly valves, ball valves and other rotary valves require IP8100, IP8000 is not applicable.

📌 Application Characteristics

制御タイプ: Continuous modulating (not on/off valve). 4~~20mA corresponds to 0~~100% valve travel.

Air source: クリーン, ドライ, oil-free compressed air. Air filter regulator (空軍) must be installed upstream.

利点: シンプルな構造, 簡単なメンテナンス, good anti-EMI performance. Suitable for sites without bus communication requirements and limited budget.

制限事項: Mechanical feedback, no auto-calibration. Manual zero and span adjustment required; no fault diagnosis.

❌ 推奨されないシナリオ

1. Severe oscillation, strong corrosive gas (extra housing protection required).
2. Remote diagnosis, HART通信, auto-tuning required → upgrade to IP8001.
3. Rotary butterfly / ball valves → select IP8100.
4. ひどい粉塵, unpurified instrument air (high risk of nozzle clogging).

SMC IP8000 — Selection Checklist

Applicable to IP8000 linear mechanical electro-pneumatic positioner; Use IP8100 for rotary applications; IP8001 smart model has separate selection rules.

1. アクチュエーター & Valve Basic Information

2. プロセス & 動作条件

3. Air Supply System Check (Highest Failure Source)

4. Electrical Check

5. Auxiliary Accessories Selection

□ Pressure gauge: 0=0.3MPa, 3=1.0MPa (select based on output pressure range)

□ Feedback lever, yoke linkage (matched to actuator stroke)

□ Air filter regulator, air tubing

□ Mounting bracket and fasteners

□ Explosion-proof cable gland (mandatory for explosion-proof models)

6. Exclusion Criteria (Do NOT select IP8000 if any applies)
7. Rotary valve (butterfly / V-ball valve) → use IP8100
8. HART通信, 遠隔診断, auto-tuning required → use IP8001
9. Unpurified air source with heavy dust, oil and condensate
10. Valve stroke >85mm or <10mm
11. Heavy corrosion, heavy shock vibration without protective measures
12. 選定例 (Model Code Reference)

IP8000-3 (1.0MPa gauge) + 防爆 + G1/4 air port + M20 electrical entry

IP8000-301: 1.0MPa gauge, standard housing, standard lever assembly

8. 設置前検査
9. Air piping fully purged to remove welding slag and debris.
10. Feedback lever near 90° at 50% 信号 (12ミリアンペア).
11. No leakage on actuator; packing friction shall not be excessive.
12. Shielded cable grounding; separate routing from power cables to avoid VFD interference.

SMC IP8000 Electro-Pneumatic Valve Positioner — Maintenance Manual

Applicable to IP8000 mechanical linear E/P positioner; Pre-work safety: Disconnect 4~20mA signal, shut off air supply and vent pressure. Never open housing under pressure.

1. Maintenance Intervals (毎日 / 四半期ごと / 年間)

1) Daily Routine Inspection (per shift / daily visual check)

1. Check housing for air leakage, 結露, corrosion and loose fittings.
2. Observe two pressure gauges for stable readings; watch for fluctuation/hunting.
3. Check valve stem movement: smooth travel, no sticking or abnormal noise.
4. Drain condensate from air filter regulator in a timely manner.
5. Check mounting bracket, feedback linkage and bolts for looseness.

Warning sign: Gauge needle jumping continuously, valve hunting → inspect feedback mechanism or nozzle blockage first.

2) Quarterly Maintenance (毎 3 月)

1. Inspect filter element of air filter regulator; replace if contaminated.
2. Check feedback lever, yoke and pin shafts: apply minimal grease (Do NOT over-lubricate! Excess grease traps dust and clogs nozzle).
3. Tighten hardware: positioner mounting bolts, tubing fittings and terminal blocks.
4. 機能テスト: input 4mA, 12ミリアンペア, 20ミリアンペア, record zero and span deviation.
5. Inspect cable and cable gland; ensure sealing intact, no water ingress.

3) Annual Overhaul (once per year; 毎 6 months under harsh conditions)

1. Disassemble unit, clean internal housing, focus on nozzle, flapper and pilot valve restrictor (highest failure point).
2. Disassemble and inspect O-rings; replace full seal kit if aged, hardened or cracked.
3. Inspect torque motor coil for overheating discoloration; check nozzle-flapper gap.
4. Re-calibrate zero and span, record calibration data.
5. Inspect air tubing; replace aged hoses.
6. Additional check for explosion-proof version: explosion joint surface undamaged, gasket intact, flameproof gap compliant.

Harsh service (ほこり, 湿度, wastewater, 紙): reduce maintenance interval by half.

2. Key Component Maintenance

✅ Nozzle & Flapper (Most Common Fault Source)

1. クリーニング: Use 0.2mm fine nylon/copper wire to gently clear nozzle orifice. Do not scratch nozzle surface with hard steel wire.
2. Blow dust with dry compressed air at low pressure (≤0.2MPa). Never flush positioner internals with liquid.
3. Flapper surface free of scratches and oil contamination. Scratches cause continuous hunting; replace nozzle-flapper assembly.
4. 要件: Instrument air must be dry and oil-free. Oil film on nozzle-flapper causes drift and oscillation.

✅ Feedback Lever Assembly

1. Apply only tiny amount of lubricant to pin shafts and pivots; no heavy grease.
2. Check linkage for deformation; no sticking during stem movement.
3. で 50% 信号 (12ミリアンペア), lever should stay near 90°. Readjust mounting if angle deviates largely.

✅ Seals (O-rings)

O-rings age and harden under large temperature fluctuation and continuous operation.

Apply thin layer of TORAY SH45 silicone grease when replacing O-rings, avoid over-application.

Prevent scratches on O-ring grooves during assembly.

✅ Electrical Section

1. Inspect 4~20mA 2-wire terminals for oxidation and looseness; single-end grounding for shielded cable.
2. Explosion-proof model: power cut before cover removal. Do not damage flameproof mating surface; seal gasket and cable gland must remain sealed.
3. Separate signal cables from power cables to avoid VFD interference.
4. Long-Term Shutdown Preservation (Out of service >1 月)
5. Shut off air supply and vent pressure; disconnect 4-20mA signal.
6. Set valve to mid-position (50% オープニング) to reduce long-term single-side spring stress.
7. Drain condensate from air filter.
8. Cover housing for dust protection to avoid dust accumulation on nozzle-flapper.
9. Purge air piping and re-calibrate zero & span before recommissioning.
10. 禁止されている操作 (重要な警告)

❌ Open positioner housing under pressure or powered condition

❌ Blast nozzle-flapper assembly with high-pressure compressed air

❌ Apply large amount of grease (traps dust and clogs nozzle)

❌ Flush internal parts with liquid (only wipe housing exterior with damp cloth)

❌ Force feedback lever; may deform torque motor and cam

❌ Use instrument air with oil, water and heavy contaminants

5. Post-Maintenance Verification Procedure

Follow sequence after maintenance:

1. Apply air supply, verify all air joints leak-free.
2. Connect 4~20mA signal generator.
3. 4mA → zero calibration; 20mA → span calibration; repeat 2~3 cycles.
4. Test linearity at midpoint 12mA; confirm no oscillation or lag.
5. Record calibration data and file maintenance log.
6. Quick Fault Reference During Maintenance
7. Valve hunting / small cycling: Dirty nozzle/flapper; wrong feedback lever angle; unstable supply air.
8. Zero drift: Condensate in air; minor O-ring leakage; slight nozzle clogging.
9. Insufficient output pressure: Stuck pilot valve; clogged air filter.
10. Large hysteresis: Pivot sticking and high friction; excessive packing friction of actuator.