ABB 기계 드라이브 ACS355-01E-02A4-2

ABB ACS355 series general machinery drive, 0.37 kW / 0.5 HP, single-phase 200–240 V input, IP20 보호, rated output current 2.4 에이. Suitable for speed control and energy-saving operation of small machinery.

1 모델 코드 설명

2 Key Technical Data

3 주요 특징

3.1 Flexible Control

Predefined application macros: 일정한 토크, fan/pump, PID 제어, 등.

Local/remote control switching via keypad, terminals or fieldbus

Built-in PID controller for closed-loop flow, 압력, 등.

3.2 안정적인 보호

과전류, 초과 적재, 과전압, 저전압, 과열, 위상 손실 보호

Motor over-temperature protection (requires external PTC)

Short-circuit and earth-fault protection

3.3 쉬운 조작

Compatible control panel with ACS350/510/550 series

Parameter copy function for fast commissioning

MTBF > 100,000 hours for continuous operation

4 일반적인 응용 분야

Small conveyors, 포장 기계

팬, 슬리퍼 (small HVAC systems)

믹서, centrifuges and small processing machines

Automatic doors, roller shutters

의료 장비, laboratory instruments

직물, printing and other light industrial machinery

5 설치 & 시운전 지침

5.1 설치 요구 사항

Must be installed in an enclosed electrical cabinet

주변 온도: 0-40°C (경감하다 10% at 40–50°C)

수직으로 장착, keep ≥ 100 mm clearance above and below for cooling

먼지를 피하십시오, 기름, 부식성 가스

Input protection: 10 A MCCB (C-곡선) or fuse recommended

5.2 Basic Commissioning Steps

1. Pre-power check: 배선 확인 (L1/N input, U/V/W output), 단자 토크, proper earthing
2. 매개변수 초기화

그룹 99: set motor rated voltage, 현재의, 힘, 속도

Select application macro (기준, PID, 등.)

3. Control configuration

로컬 제어: via control panel

원격 제어: via DI terminals or optional Modbus RTU

4. Operation test

무부하 테스트: run at 5–10 Hz, check rotation and stability

부하 테스트: gradually apply load, verify current and temperature

Adjust acceleration/deceleration time (1–10 s recommended)

6 Cross-Brand Replacement Options (0.37 kW, 1-단계 220 다섯, IP20)

7 선택 & 유지 관리 팁

7.1 Recommended Options

Braking function: optional braking resistor (75 오 / 50 W recommended)

의사소통: add RS485 module

Enhanced EMC: additional input EMC filter

7.2 유지

Clean cooling channels every 6 개월

Check terminal torque annually

Avoid frequent starts/stops (≤ 20 times per day)

보관온도: -25°C ~ +60°C, dry environment

ABB ACS355-01E-02A4-2

Installation and Commissioning Manual

Overview: This manual provides complete instructions for safety, 설치, 배선, parameter setting and commissioning of the ACS355-01E-02A4-2 drive (0.37 kW / 0.5 HP, single-phase 200–240 V) for general machinery speed control and energy saving.

1 Safety Instructions (꼭 읽어야 할)

1.1 Electrical Safety

Power-off procedure: Disconnect all power before installation, wiring or maintenance. 기다리다 5 minutes for internal capacitors to discharge.

접지: PE terminal must be reliably earthed (earth resistance ≤ 4 오)

과전류 보호: Install 10 A MCCB (C-곡선) or fuse on input side

절연 테스트: Only test motor cables; do NOT apply voltage to the drive itself

1.2 Mechanical Safety

Rotating parts (샤프트, coupling, pulley) must be guarded

Mount vertically on solid surface to avoid vibration

Do not modify internal circuits or structures

1.3 Environmental Safety

작동 온도: 0-40°C (경감하다 10% at 40–50°C)

습기: 5–95% 상대습도, 비응축

IP20: must be installed in enclosed cabinet

2 Product Overview and Model Identification

2.1 모델 설명 (ACS355-01E-02A4-2)

2.2 핵심사양

3 설치 절차

3.1 준비

1. Unpack and inspect drive for damage
2. Choose well-ventilated, dust-free location inside cabinet
3. 도구: 십자 드라이버 (PH2), 와이어 스트리퍼, 압착 도구, 멀티미터, insulation tape

3.2 설치

1. Mount vertically on flat metal plate
2. Keep ≥ 100 mm above/below, ≥ 50 mm left/right clearance
3. Fix with M4 screws, 조임 토크: 1.2–1.5 N·m

4 Electrical Wiring

4.1 Terminal Description (ACS355-01E Series)

4.2 배선 단계

1. Power wiring: L1/N to mains, PE to earth, U/V/W to motor
2. Control wiring (Standard macro example):

DI1: Forward (FWD), DI2: Reverse (회전), DI3: 다시 놓기

AI1: Speed reference (0–10 V)

3. Check torque, 격리, and phase sequence

5 매개변수 설정

5.1 Keypad Functions

▶/■: 시작 / 멈추다

▲/▼: Adjust value

입력하다: 확인하다

ESC: Back

LOC/REM: Local / Remote

5.2 Quick Motor Settings (그룹 99)

5.3 Common Application Parameters

6 Commissioning Flow

6.1 Pre-Power Check

Correct power and control wiring

Motor and drive area clear

Cabinet ventilation OK

입력 전압: 200–240 V single-phase

6.2 First Power-Up

Close MCCB, display shows REM or LOC

Check for fault codes

Verify Group 99 motor parameters

6.3 모터 식별 (선택 과목)

Set 9910 = 2 (ID Run)

Press ENTER; drive runs motor briefly

Completed when shown COMPLETE

6.4 무부하 테스트

Switch to LOCAL

Run at 5 헤르츠, check rotation

Increase to rated frequency, check noise and vibration

6.5 부하 테스트

Switch to REMOTE

Control speed via AI1

Check output current ≤ 2.4 에이

Adjust acc/dec to avoid overcurrent

Test protection functions

7 문제 해결

7.1 일반적인 오류 코드

7.2 Typical Issues

8 유지

8.1 정기 유지 관리

Clean cooling channels every 6 개월

Check terminal torque annually

Log operating current and temperature

8.2 Long-Term Storage

온도: -25°C ~ +60°C

마른, ventilated environment

Power on for 1 hour every 6 개월

9 Appendix: Options and Replacements

9.1 Recommended Options

제동 저항기: 100 오 / 50 여

EMC 필터

RS485 Modbus RTU module

Shielded cable for control wiring

9.2 브랜드 간 대안 (0.37 kW, 1-단계 220 다섯, IP20)

Manual Version: V1.0 (based on ABB official ACS355 manual, adapted for ACS355-01E-02A4-2)

Effective Date: February 2026

Copyright: ABB Group, 모든 권리 보유