AIRTAC DMSE-PNP Cylinder Magnetic Sensor

Complete standard model: DMSE-P020 / DMSE-P030 / DMSE-P050, commonly referred to as DMSE-PNP in the industry. E-profile slot type, 3-wire PNP output, non-contact electronic cylinder magnetic sensor.

모델 정의

DMSE-P020

DMS: Electronic magnetic sensor series

이자형: E-profile (fits E-slot of 북극 남동쪽 / SAE series cylinders)

피: 3-wire PNP output; N = NPN output

020: Cable length 2 m; 030 = 3 m; 050 = 5 m

Connector version: DMSE-PM08 (M8 male connector, 0.5 m cable)

주요 전기 사양

3-Wire Wiring Definition

갈색: DC24 V Positive

파란색: 0 V Negative

검은색: PNP signal output (connect to PLC input terminal)

PNP 출력: High-level signal (대략. 공급 전압) on black wire when magnet is detected. Suitable for PLC sinking-type input terminals.

Compatible Cylinders

Specially designed for E-slot cylinders: 남동쪽, SAE series cylinders.

Cannot be directly mounted on SC / SDA cylinders. SC uses G-profile DMSG; SDA uses J-profile DMSJ, corresponding mounting brackets are required.

Comparison within the Same Series

1. DMSE-Pxxx: E-slot, for SE/SAE cylinders, PNP; DMSE-Nxxx = NPN version
2. DMSG-Pxxx: G-slot, for SC/SGC cylinders
3. DMSJ-Pxxx: J-slot, for SDA/TCL cylinders
4. DMSH-Pxxx: H-slot, for ACQ compact cylinders

선택 지침

1. Confirm cylinder groove profile: 이자형 / G / 제이 / 시간; wrong profile prevents installation.
2. PLC input type: PNP output matches PLC sinking-type input.
3. 케이블 길이: 2 m(020), 3 m(030), 5 m(050); M8 connector version supports quick harness plug-in.
4. Advantages of electronic type: 고주파 작동, 긴 서비스 수명. No mechanical contacts compared with CMS reed-switch series, suitable for high-speed reciprocating motion.

Common Replacements

국내 대안: Domestic E-profile PNP magnetic sensor with parameters DC5-30V, 200 엄마, E-section profile.

Interchangeable: DMSE-P020 ↔ DMSE-P030 differ only in cable length.

AIRTAC DMSE-PNP (DMSE-P020) 설치

Direct-mount type: Fits E-shaped slot of SE / SAE cylinders; 추가 브래킷이 필요하지 않습니다, clip directly into the side E-groove of cylinder barrel.

Step-by-Step Installation Procedure

1. Loosen set screw: Use small flat-blade screwdriver to turn the set screw on sensor head counter-clockwise (do not remove it completely).
2. Slide into groove: Insert DMSE sensor from the end of the E-shaped side groove on SE/SAE cylinder barrel. Keep flat bottom surface of sensor tight against groove base.

⚠️ Only for SE, SAE cylinders with E-slot. Not applicable for SC/SDA or other slot-profile cylinders.

3. Position adjustment: Manually move cylinder piston, slide magnetic sensor to desired detection position (signal triggers when piston magnet ring passes this position).
4. Tighten and fix: Fasten the head set screw

권장 토크: 0.15-0.20 N·m, maximum ≤0.25 N·m. Excessive torque will crack plastic housing.

중요한: Screw tip must NOT protrude from sensor bottom surface; otherwise it will jam and scratch cylinder groove.

5. Verification test: Manually cycle cylinder piston to confirm reliable signal triggering. Re-adjust screw if position needs fine-tuning.

Installation for Cylinders without E-slot

If your cylinder is non-SE/SAE without E-shaped groove:

DMSE has no universal hoop bracket and cannot be fitted directly. Select magnetic sensors with corresponding profile (DMSG / DMSJ / DMSH) and use dedicated mounting brackets.

배선 (3-wire PNP)

갈색: DC24 V+

파란색: 0 다섯 / 접지

검은색: PNP signal output (connect to PLC sinking-type input point)

Key Installation Notes

1. Cylinder must be equipped with built-in magnet ring, otherwise magnetic sensor cannot detect signal.
2. Prevent cable from following cylinder reciprocating movement; reserve cable slack. Minimum bending radius ≥19 mm to avoid cable fatigue fracture.
3. Keep away from strong magnetic fields (솔레노이드 코일, welding equipment etc.) to avoid false triggering.
4. Do not use sensor as mechanical stop. Cylinder shall be equipped with built-in buffer; forbid piston impact onto sensor.
5. Retighten screws periodically. Equipment vibration may cause position shift.

빠른 문제 해결

출력 신호 없음: ① Verify cylinder has magnet ring; ② Check whether sensor aligns with piston magnet ring; ③ Over-torque causing housing deformation; ④ Reversed power-supply wiring.

잘못된 트리거링: Strong surrounding magnetic interference; too-small spacing between two magnetic sensors.

AIRTAC DMSE-PNP (DMSE-P020) 출력 특성

출력 유형: 3-wire PNP, 트랜지스터 출력, 평상시 열림 (아니요), 소싱 출력

Level Logic

When cylinder magnet ring is detected: Signal wire (검은색) outputs high-level voltage nearly equal to supply DC24 V.

No magnet detected: Signal wire is high-impedance state (출력 없음).

배선

1. 갈색: DC24 V positive
2. 파란색: DC0 V negative
3. 검은색: PNP signal output terminal

PNP sourcing output: Sensor sources 24 V voltage outward.

✅ 호환 가능: PLC sinking-type input module

❗Caution: Cannot connect directly to PLC sourcing-type input, signal will not be recognized.

Electrical Output Specifications

Output structure: Bipolar transistor, non-contact electronic design

Max load current: 200 엄마

Load voltage range: DC5-30 V

Max load power: 6 여

출력 모드: Factory preset Normally Open (아니요), no Normally Closed version available

응답 빈도: 1000 헤르츠, suitable for high-frequency cylinder reciprocation

Load Connection Methods

1. Connect to PLC sinking-type input: Black wire connects to PLC input channel; PLC common COM terminal connects to 24 V-. When magnet is detected, input channel receives 24 V and PLC turns ON.
2. Connect to relay coil: One end of relay coil connects to black signal wire; the other end connects to 0 V. Relay energizes upon magnet detection.

Common Misunderstandings

1. DMSE-Pxx: PNP sourcing output; DMSE-Nxx: NPN sinking output.
2. This is electronic sensor, not dry-contact relay. It requires DC power supply; cannot be used as passive switch.
3. Without piston magnet ring, no signal will be generated regardless of wiring.

Simple memory rule: PNP outputs high-level voltage; NPN pulls signal down to 0 V.

AIRTAC DMSE-PNP (DMSE-P020) Material Specification

DMS-series electronic magnetic sensor, divided into housing, 케이블, fasteners, internal potting compound.

1. Sensor Main Housing

재료: Impact-resistant PBT engineering plastic (Off-white housing, blue cable retainer ring also PBT).

Properties: 충격 방지, wear-resistant, resistant to general oil contamination; operating temperature-10 ℃ ~ +70 ℃; IP64 protection; 50 G shock resistance.

메모: 플라스틱 하우징; tightening torque shall never exceed 0.25 N·m, over-torque causes cracking.

2. 출력 케이블 (Standard A05 General-purpose Version)

Jacket: High-flexibility PVC grey cable, 3-core copper conductors, anti-bending performance for robot / cable-chain applications.

A06 oil-resistant version: Special oil-resistant cable (yellow retainer ring, IP68), model suffix -W for DMSE-P-W oil-resistant & waterproof variant.

3. Set Screw

Stainless steel flat-head machine screw, for locking sensor into cylinder E-slot.

4. Internal Construction

Magnetic sensing components + PCB circuit board, epoxy resin potting. Circuit is fully sealed inside plastic housing to achieve dust-proof and water-proof performance.

DMS is electronic type, no reed-switch glass tube. (CMS series adopts reed-switch glass tube).

Version Differentiation

1. Standard DMSE-P020: PBT housing + PVC high-flex cable, IP64, blue cable retainer.
2. Oil-resistant waterproof DMSE-P020-W: PBT housing + oil-resistant cable, yellow retainer ring, IP68, suitable for cutting-fluid and splash-water environments.

Material-Related Usage Precautions

1. PBT housing shall avoid immersion in strong acid, strong alkali and strong solvents.
2. PVC cable shall avoid contact with strong organic solvents, otherwise accelerated aging and cracking will occur.
3. Plastic housing shall not suffer hard-object impact or knocking.