지게차 선형 경계등

(DC12~80V 넓은 전압)

Also known in the industry: linear warning light, linear safety marker light, ground marking light. It projects a straight line beam to mark the working boundary and reversing warning zone of forklifts.

주요 사양

전원공급장치: DC 12–80V wide voltage, built-in constant current driver. Compatible with 12V/24V/48V/80V electric forklifts, lithium forklifts, AGV, stackers and aerial work platforms. Reverse polarity protection included. Red wire = positive, black wire = negative.

광원: 주도의. Optional red / 파란색 / 녹색 (red and blue are mainstream for factories).

전력 등급: Common options 5W /18W /20W /30W.

진입 보호: IP67, 방진 및 방수, suitable for workshops, cold storage and humid warehouses.

주택: Die-cast aluminum alloy for vibration resistance and heat dissipation; acrylic focusing lens for sharp light line.

서비스 수명: Typical 30,000～50,000 hours.

설치: Stainless steel adjustable bracket, fixed with M8 bolts, 각도 조절 가능.

응용

Project a straight line on the ground to indicate the overall width of the forklift and reversing safety boundary, alerting pedestrians.
Anti-collision warning in low-light warehouses, night operations and AGV collaboration areas.
Can be installed in pairs at the rear / side of forklifts, or installed singly as a reversing limit line.

선택 지침

Short single-lens version: Narrow and thin light line, suitable for small-tonnage forklifts and AGVs.

Long three-lens version: Longer and brighter light line, suitable for large-tonnage internal combustion / lithium forklifts.

구별: Linear straight version vs U-shaped (curved) boundary light and arrow warning light, 그것들을 섞지 마세요.

The quality of wide-voltage IC is critical. Low-quality units tend to suffer rapid light decay or burnout at high voltage (72–80V).

설치 & 배선

Direct connection to forklift DC power supply, no extra step-down module required, which is the biggest advantage of the 12–80V wide-voltage model.

Recommended mounting height above ground: 2–3 m, projection distance 2–5 m for clear, non-diffused light line.

Cable routing shall be abrasion-resistant and kept away from oil cylinders and moving chains.

호환 장비

Heli, Hangcha, Lonking, Tailift and other electric forklifts, AGV, aerial work platforms, loaders and small construction machinery.

Work Instruction (SOP) for Forklift Linear Boundary Light Installation

해당되는: DC12–80V wide-voltage LED linear boundary light for ground safety marking at forklift sides or rear. Covers mechanical installation, electrical work, optical commissioning, safety specifications, acceptance and maintenance.

장착 위치 & Mechanical Requirements
장착 위치

Standard scheme: Install in pairs at upper left and right rear positions or side overhead guard posts; side mounting on overhead guard uprights is also acceptable. Do NOT install on mast, forks, oil cylinders or other moving components (lifting mast changes light position and causes false warning or lamp damage).

Mounting height: 2.0～3.0 m above ground is recommended. Height below 1.8 m results in too short line; height over 3.2 m causes light diffusion and insufficient brightness.

Projection angle: Tilt the lamp downward to project onto the ground behind or beside the forklift. The starting point of the marking line shall be 0.3～0.8 m away from the outer contour of the forklift body, and line length is 2～5 m as required. Left and right lamps shall be installed symmetrically with consistent angles.

Clearance requirement: Keep away from exhaust pipes, hydraulic hoses, chains and moving parts; shall not block driver’s view, original turn signal lights, brake lights or reverse lights.

Fastening Structure

Use original matched adjustable brackets (강철 / 스테인레스 스틸). M6 or M8 bolts are preferred, fitted with flat washers, spring washers and lock nuts. Locking is mandatory due to continuous forklift vibration; ordinary nuts alone are not allowed.

The lamp body is die-cast aluminum. Tighten with proper torque; the lens shall not bear squeezing force. Lock adjusting screws after light angle setting to prevent shifting caused by vibration during travel.

진동 저항: Forklifts endure bumping, start and brake impact. Reinforcing backing plates are required if the mounting sheet metal is thin, to avoid tearing the overhead guard.

Mechanical Protection

The exposed lens shall not face directions prone to impact by goods or pallets. Protective mesh cover can be added if necessary.

IP rating of housing ≥IP67. Arrange mounting seam and cable outlet downward to prevent water ingress along cables.

전기 배선 요구 사항 (Critical for 12–80V Wide-Voltage Model)
전원 회로

전원공급장치: DC 12～80V, compatible with 24V/48V/72V lithium forklifts. Confirm the lamp is equipped with built-in wide-voltage constant current driver; no external step-down module needed.

극성: Red for positive, black for negative. Reverse polarity protection is integrated, yet reverse connection shall be avoided as sustained reverse connection may damage the driver.

Recommended power tapping: Tap from reverse light circuit (auto-on when reversing), or fit independent rocker switch for permanent on. Direct connection to battery terminal without protection is not recommended.

회로 보호

Fuse for each lamp circuit: ≤5A for single lamp; 5A～10A slow-blow fuse for two lamps shared. Install fuse close to the tapping point.

Cable selection: For oily and vibrating forklift environment, use oil-resistant, flexible multi-strand flame-retardant automotive wire. 0.75 mm² minimum; 사용 1.0 mm² for cable length over 3 중.

Cable routing: Run harness along frame and overhead guard, protected by abrasion-resistant corrugated tube or braided sleeve. Keep away from high-temperature areas, sharp edges and hydraulic pipelines. Fasten clips at intervals ≤300 mm; leave slight slack, do not pull tight.

종료: Waterproof aviation plug is preferred. If crimped directly, seal with waterproof heat shrink tube; bare copper shall not be exposed. Ordinary adhesive tape is prohibited (fails quickly under oil and moisture).

절연 테스트: Measure insulation resistance to ground after power-off wiring; insulation resistance ≥1 MΩ.

EMC Requirements (Important for Export & AGV Applications)

The wide-voltage driver shall have good anti-interference performance. Route cables away from forklift controllers, instruments and CAN bus to avoid signal disturbance.

광학 & Light Line Commissioning Requirements
Linear beam: Project a sharp solid line on the ground with clean edge, no obvious stray light, blurred edge or uneven brightness.
명도: The marking line shall be clearly visible under normal warehouse lighting; meanwhile no glare towards human eyes. Never angle the lamp upward during adjustment.
Symmetry: For paired left-right installation, two boundary lines shall be parallel and aligned with forklift side contour; marking line represents warning boundary and shall not be skewed.
환경 적응: High-brightness version is preferred for cold storage and dusty workshops. Red or blue light shall follow site safety regulations (blue boundary light is specified in many factories).
안전 사양
This lamp is an auxiliary safety warning device. It cannot replace original reverse buzzer, reverse light or turn signal light, and only provides visual boundary reminder.
Do not block original statutory lamps or damage the original protection logic of vehicle wiring.
For internal combustion forklifts: Route cables away from high-temperature exhaust parts; cable temperature rating shall match ambient condition. For lithium forklifts: Do not damage battery pack BMS and high-voltage circuits.
Operation zone: The projected marking is only for pedestrian warning. Do not project onto main aisles or dazzle operators of opposite equipment.
Acceptance Checklist after Installation

Brackets are firm without looseness, locking hardware complete, no moving interference

Harness well fixed, waterproof connectors sealed, no cable damage or extrusion

전원 켜기 테스트: Normal lighting and no flicker within 12–80V working range

Clear light line at correct position, no glare

Reverse-linked version: Lights on automatically when reverse gear engaged, off when disengaged

Vibration check: Shake frame or run engine at idle; light does not flicker or shift angle

No short circuit or abnormal heating: Continuous operation for 30 분, lamp housing and wiring at normal temperature rise

유지 보수 요구 사항
Tighten bracket screws monthly; inspect cable abrasion and aging of waterproof connectors.
Lens cleaning: Wipe with soft cloth. Hard objects are forbidden to scratch the lens (scratches cause light diffusion and failure).
Troubleshooting for flickering / intermittent lighting: Check loose connection and water ingress at connector first, then inspect the driver.