Siemens 3RQ2000-1BW00 Coupling Relay

Industrial coupling relay of Siemens SIRIUS series, 갖춘 2 전환 연락처, wide voltage range 24-240V AC/DC and screw terminals. It serves as a replacement for 3TX7002-1CB00 and 3RS1800-1BW00, and is designed for PLC signal isolation and control circuit coupling.

1. 모델 코드 해석

성명: Enclosed industrial coupling relay, 2 전환 연락처, 24-240V AC/DC wide voltage, 나사식 터미널 연결.

2. 핵심 기술 매개변수

3. Cross-brand & Obsolete Model Replacement List

선택 팁: Verify full consistency of contact quantity, 터미널 유형, mounting dimensions and electrical parameters before replacement.

4. Full Model List of 3RQ2000 Series

5. 일반적인 결함 & 문제 해결

6. 적용범위 & 산업 사례

6.1 적용 가능한 시나리오

PLC Signal Isolation: Couple signals between PLC outputs and field actuators to protect PLC modules.

제어 회로 확장: Increase available control signals to drive multiple loads via one signal.

Voltage Conversion: Connect control circuits with different voltage levels, 예를 들어. 24V DC PLC output for 220V AC contactors.

Interference Suppression: Isolate signals in high-interference environments such as inverters and welding equipment to avoid false triggering.

산업 자동화 시스템: 생산 라인 제어, 포장 기계, 공작기계, 컨베이어 시스템, 등.

6.2 권장되지 않는 시나리오

High-frequency switching: Not suitable for frequent switching over 10 cycles per second.

Inductive load without protection: Surge suppressors are mandatory when driving inductive loads such as motors and solenoid valves.

Corrosive environments: No special anti-corrosion treatment; not for strong acid, alkali or high salt mist conditions.

Explosive hazardous areas: 비방폭 설계; prohibited for flammable and explosive locations.

6.3 일반적인 적용 사례

사례 1: 자동차 부품 생산 라인

애플리케이션: PLC controls clamps and welding torches of robotic welding stations.

구성: 3RQ2000-1BW00 isolates PLC output signals from 220V AC solenoid coils.

결과: Resists welding current interference; failure rate reduced by 90%, 유지관리 비용 절감 50%.

사례 2: 음식 & Beverage Filling Line

애플리케이션: Connect HMI touch panel and filling valve control circuits.

구성: Two units of 3RQ2000-1BW00 control 4 filling valves (2 아니요 + 2 NC) via one HMI signal.

결과: 단순화된 배선, improved system reliability and fewer spare part types.

사례 3: 지능형 창고 시스템

애플리케이션: Isolate position sensor signals of stacker cranes and PLC inputs.

구성: 3RQ2000-1BW00 converts 24V DC sensor signals to PLC-compatible signals.

결과: Eliminates interference from long-distance signal transmission; positioning accuracy improved to ±1mm.

7. 선택 지침 & 빠른 참조 규칙
8. Contact quantity by letter: A = 1CO, B = 2CO, C = 3CO
9. Terminal type by digit: 1 = Screw terminal, 2 = Spring terminal
10. Contact material by suffix: W = Standard contact, CW01 = Gold-plated contact
11. Universal voltage: Full series supports 24-240V AC/DC
12. Priority for replacement: Directly replace 3TX7 / 3RS18 series with corresponding 3RQ2000 models

Ordering Notice: Standard package: 1 unit per box; 최소 주문 수량: 1 단위. It is recommended to prepare 2~3 units as spare parts for general industrial automation control.

Common Faults and Troubleshooting of Siemens 3RQ2000-1BW00 Coupling Relay

1. Relay Fails to Operate Completely
2. No power supply to coil

Measure input voltage to confirm it is within 24~240V AC/DC. Check circuit breakers, fuses and continuity of upstream control circuits, and tighten loose terminals.

2. Loose / poor terminal connection

Retighten screw terminals. Check wire crimping, broken wires and wires trapped under terminal screws.

3. 구운 코일

Long-term overvoltage or frequent voltage surges will burn the coil. Replace the relay if burnt marks or abnormal odour are observed.

4. 기계적 방해

Accumulated dust and continuous vibration cause internal armature sticking. Tap the housing gently for test; replace the relay if the issue persists.

2. Coil Pulls In but Contacts Open / Poor Contact
3. Oxidation and dust accumulation on contacts

Commonly seen in humid and dusty environments, especially for low-power signal circuits. Clean contacts after power cut and test with repeated switching operations.

2. 접촉용접

Excessive load current or frequent inrush load leads to stuck contacts. Disconnect the load for verification. Replace the relay as welded contacts cannot be repaired.

3. Fault on load side circuit

Troubleshoot downstream contactors, solenoid valves and broken wires. Confirm relay fault only after excluding external failures.

3. Random Operation / Unexpected On & 끄다
4. 전자기 간섭

Easily affected when installed close to inverters, 모터, high-power contactors or long control cables. Route control cables away from power cables and apply shielded wires and surge absorbers.

2. Voltage fluctuation & electrical noise

Sudden voltage drop and voltage spikes cause false operation. Install voltage stabilizers and filters on the upstream side.

3. Abnormal ambient temperature

Operation above +60°C or condensation under low temperature leads to internal circuit malfunction. 환기 개선, dehumidification and heat dissipation.

4. Abnormal Indicator Light
5. Light off, relay works normally

Only the LED bulb is damaged. The relay can remain in service or be replaced.

2. Light always on / 꺼질 것 같은, relay does not operate

Malfunction of internal voltage divider and indicator circuit, usually accompanied by coil failure. Replace the relay directly.

5. Overheated Wiring Terminals
6. 느슨한 배선: Retighten terminals to specified torque.
7. Undersized wire gauge: Replace with cables with cross-section matching the load current.
8. Continuous overload: Actual load exceeds rated 5A contact current. Apply load sharing or use higher-capacity relay.
9. Frequent Failures under Inductive Load (Solenoid / 접촉기)

Symptoms: Shortened contact service life, frequent contact welding and unexpected tripping

문제 해결: The absence of surge suppressors causes reverse high voltage from inductive loads to damage contacts during power-off. Connect freewheeling diodes (DC의 경우) or RC snubbers (AC용) in parallel across inductive loads.

7. On-site Quick Troubleshooting Procedure
8. Cut off power → Inspect appearance, wiring and terminal tightness
9. Switch on power → Measure input control voltage
10. Observe indicator light and listen to pull-in sound to judge coil status
11. Cut off power → Test NO/NC contacts with multimeter continuity mode
12. Distinguish faults among upstream control circuit, relay itself and downstream load circuit