지멘스 7NG3211 온도 트랜스미터

지멘스 7NG3211 Head-Mounted Pt100 Temperature Transmitter

1. 기본 제품 포지셔닝

7NG3211 corresponds to SITRANS TH100. It is a 2-wire 4–20 mA head-mounted transmitter dedicated exclusively to Pt100 without HART communication. It only supports resistance temperature detectors (RTDs) and is incompatible with thermocouples. Designed to fit DIN Type B connection heads (44 mm round), it serves as a general-purpose basic temperature transmission module for chemical, power and HVAC industries.

Full Order Code Breakdown (7NG3211-XNNXX)

Take common models `7NG3211-0AN00` and `7NG3211-1NN00` as examples:

1. 7NG3211: Fixed series prefix, representing standard round plastic housing of TH100
2. 1st suffix digit: Explosion-proof certification

0 = Intrinsically safe ATEX Ex ia/ib and NEPSI certification (for Zone 0/1 위험 지역)

1 = Standard non-explosion-proof type (for ordinary safe areas)

3. 2nd character A/N: No electrical isolation (all TH100 variants feature no isolation)
4. Last three digits 00: Standard terminals, no optional extra functions
5. 핵심 전기 & Measurement Specifications

2.1 입력 (Pt100 IEC60751 only)

배선 호환성: 2-철사 / 3-철사 / 4-wire Pt100, configurable via software

측정 범위: -200 ~ +850°C

Minimum span: 25℃; Maximum span: 1050℃

Maximum total wire resistance: ≤20 Ω (suitable for long cables)

Measuring current: 0.4 엄마, with immunity to 50/60 Hz power frequency interference

정확성 (at 23°C ambient temperature): ≤0.1%FS; Temperature drift ≤0.1%FS per 10°C; Repeatability ＜0.1°C

Sensor fault signal (개방 회로 / 단락): Compliant with NAMUR NE43, configurable as either low fault level (3.6 엄마) or high fault level (22.8 엄마)

Filter damping: 조정 가능 0 에게 30 s via software, factory preset to 0 에스

역극성 보호, 12-비트 해상도

2.3 환경 & 기계적 매개변수

작동 온도: -40°C ~ +85°C (transmitter body)

치수: Φ44 mm, 두께 20.8 mm; 무게: 50 g

Max cross-section of cable for terminals: 2.5 mm²

보호구조: Potting plastic housing, compatible with standard temperature sensor connection heads

3. Terminal Definition & 배선

Six terminals in total, divided into power circuit (터미널 1, 2) and Pt100 sensor circuit (터미널 3, 4, 5, 6)

1. 단말기 1 (+): Positive pole of 24 V DC 전원 공급 장치
2. 단말기 2 (-): Negative pole of 4–20 mA signal (shared ground for 2-wire loop)

3/4/5/6: Terminals for Pt100 RTD wiring

3-wire Pt100: 터미널 3 그리고 4 connect to two ends of RTD, 단말기 5 for compensation wire, 단말기 6 vacant

4-wire Pt100: Terminals 3&4 as one pair, Terminals 5&6 as another pair to eliminate lead resistance error

Critical note: 배선 후, 2/3/4-wire Pt100 mode must be matched via SIPROM T software; otherwise severe temperature deviation will occur.

4. 구성 & Calibration Method
5. Mandatory tools: SIPROM T configuration software + dedicated USB modem
6. Configurable parameters:

Upper/lower measuring range limits, temperature unit (℃ / °F)

Switch between 2-wire / 3-철사 / 4-wire Pt100 modes

Filter damping time, sensor offset compensation (±100°C)

Fault output level (low limit: 3.6 엄마 / high limit: 22.8 엄마)

3. 한정: No HART protocol support. Calibration via handheld communicator is unavailable; offline configuration via computer USB only.
4. Explosion-Proof Certification List (0AN00 Explosion-Proof Model)

ATEX Ex ia IIC T4/T5/T6, FM and NEPSI intrinsic safety certifications. Applicable for flammable and explosive working conditions in Zone 0/1; Compliant with dust explosion protection Zone 21/22 표준.

6. 핵심 차이점: TH100 (7NG3211) vs TH200 vs TH320

7. Typical Troubleshooting Matrix

8. Alternative Selection Solutions
9. Upgraded models with identical head-mounted installation form factor

Remote calibration with HART required: 7NG3212 TH200

Thermocouple compatible with electrical isolation: 7NG3213 TH320

2. Domestic substitutes for discontinued / out-of-stock units: 44 mm round head-mounted 2-wire 4–20 mA Pt100 transmitters with fully compatible mounting dimensions
3. DIN rail mounted alternative: Siemens SITRANS TR100 DIN rail temperature transmitter module
4. Industrial Application Scenarios

전력산업: Temperature measurement for boilers, steam turbines and auxiliary equipment bearings

화학적인 & petrochemical industry: Explosion-proof temperature acquisition for pipelines and reactors

제약 & food industry: Temperature monitoring for sanitary tanks and heat exchangers

공조: Pt100 temperature detection for air ducts and chillers

Output Signal of Siemens 7NG3211 (SITRANS TH100)

1. Standard output type: 2-wire 4～20 mA analog current signal
2. No HART protocol support: Pure analog current output only, digital communication not available
3. Signal correspondence:

Minimum measuring temperature → 4 엄마

Maximum measuring temperature → 20 엄마

4. Two optional fault outputs (compliant with NAMUR NE43, 소프트웨어 구성 가능):

Low fault level: 3.6 엄마 (sensor open circuit)

High fault level: 22.8 엄마 (sensor short circuit)

5. Over-range output: 3.84 mA when measured value below lower range limit; 20.5 mA when measured value above upper range limit
6. Power supply and signal share two wires; loop load driven by 24 V DC 전원 공급 장치.

Full Accuracy Specifications of Siemens 7NG3211 (SITRANS TH100)

(Standard test condition at 23°C specified in original manufacturer manual)

1. Overall Basic Measuring Accuracy (Key Indicator)
2. Span ＜ 250°C: Maximum error ＜0.25°C
3. Span ＞ 250°C: Maximum error ＜0.1%FS (Full Scale)
4. Nominal overall basic error for the unit: ＜0.1% of measuring span (at 23°C ambient temperature)

Calculation Examples for Intuitive Understanding

Range 0～100°C (span 100°C ＜ 250°C): Max error ±0.25°C

Range 0～500°C (span 500°C ＞ 250°C): 500 × 0.1% = ±0.5°C

2. Repeatability Accuracy

＜0.1°C, minimal fluctuation in repeated temperature measurements

3. Temperature Drift (Additional error induced by ambient temperature variation)

Max drift value: 0.1%FS per 10°C

예: 20°C ambient temperature fluctuation brings an extra 0.2% full-scale error

4. Other Additional Error Terms
5. Supply voltage influence: ＜0.01%FS per V
6. Load resistance influence: ＜0.025%FS per 100 오
7. Long-term drift: ＜0.025%FS per month
8. Measuring resolution: 14-조금
9. 보충 설명
10. Stated accuracy only applies to the transmitter body, excluding inherent error of Pt100 sensor itself.
11. No built-in electrical isolation; extra measuring deviation will be introduced at sites with severe electromagnetic interference.
12. 2/3/4-wire Pt100 mode must be correctly configured via SIPROM T software; otherwise systematic deviation of several degrees Celsius will occur.

Translation Notes for Industrial Standard Terms