Однофазное твердотельное реле OMRON G3PA-260B-VD

Тип продукта: Single-phase SSR (Твердотельное тело Реле), integrated heat sink, zero-cross turn-on

Вход: DC 5~24V; Выход: AC 24~240V, 60А @ 40℃

1. Ключевые характеристики

Control Input: DC 5–24V, max control current 7mA; operate voltage ≤4V, release voltage ≥1V

Напряжение нагрузки: AC 24～240V (operating range 19～264VAC, 50/60Гц)

Номинальный ток: 60А (АС-1, 40℃); derate to 48A when densely installed side-by-side

Surge Current: 440А (60Гц, 1 цикл); VDRM 600V

On-state Voltage Drop: ≤1.6V RMS; Off-state Leakage Current: ≤20mA @ 200VAC

Trigger Mode: Zero-crossing Turn-on, minimizes inrush & EMI

Изоляция: Phototriac optocoupler isolation

Диэлектрическая прочность: 4000VAC 1min; Insulation Resistance ≥100MΩ (500 В постоянного тока)

Монтаж: DIN-рейка / винтовое крепление; with operation indicator

Температура окружающей среды: -30～+80℃ (нет конденсата); Хранилище: -30～100℃

Особенность: Replaceable power cartridge for low maintenance cost

2. Расшифровка номера модели

G3PA: Series of high-current SSR with replaceable power modules

2: Output voltage class AC24–240V (4 = AC200–400/480V high voltage)

60: Rated current 60A

Б: Integrated heat sink

VD: DC voltage input (DC5–24V)

3. Типичные применения

Resistive AC loads such as heating tubes, infrared lamps, вентиляторы и конвейеры; напрямую управляется транзисторными выходами ПЛК.

Примечание: Add varistor/RC snubber for inductive motor loads; never operate over current or over temperature.

4. Same Series Cross Reference

Генеральный директор G3PA-240B: 24–240 В переменного тока, 40А

G3PA-430B-VD: AC200–400V, 30А

5. Domestic Equivalents (DC5-24V input, 24-240 В переменного тока, 60A zero-cross SSR)

Meigeer MGR-1 D60

Ximanton H360ZF

Yangming SSR-60DA-H

Application Scenarios for G3PA-260B-VD

Core features summary: DC5–24V control, AC24–240V single-phase output, 60А, zero-cross trigger, built-in heat sink, field-replaceable power cartridge, PLC direct drive, бесконтактный, высокочастотное переключение. First choice for resistive heating loads.

Напоминания: This is a single-phase SSR; использовать 3 units in parallel for 3-phase heating control (one per phase).

Основные приложения (Best Match)

1. Temperature-controlled heating systems (largest application)

Промышленные печи, сушильные шкафы, thermostatic baths, камеры для испытаний на старение; barrel heating for injection & extrusion machines, mold temperature controllers; heat-seal blades, hot plates on packaging machines; electroplating tank heaters, thermal oil heaters.

Преимущество: Zero-cross switching avoids voltage spikes; matches PID time-proportion control from temperature controllers; contact-free design delivers ultra-long life for frequent cycling.

2. High-power resistive lighting

Infrared heating lamps, halogen lamps, greenhouse supplementary lighting arrays.

✘ Not recommended: Fluorescent lamps & Источники питания светодиодов (inductive/capacitive surge loads).

3. Light-duty fans & конвейеры (inductive loads with surge protection)

Маленькие центробежные вентиляторы, hot air circulation blowers, single-phase conveyor motors with infrequent starts.

⚠️ Motors are inductive loads; external varistor/RC snubber is mandatory to suppress back EMF, otherwise the SSR will break down easily. Not suitable for large motors or frequent forward/reverse operation.

Other General Automation Applications

1. Упаковочное оборудование: Heat shrinkers, hot-knife cutters, hot air power control
2. Резина & plastic equipment: Heating platens for vulcanization & thermoforming molds
3. Environmental test equipment: Heating circuits in temperature & humidity chambers
4. Пищевое оборудование: Baking lines, fryer heating elements, thermal blanching equipment
5. ОВК: Electric duct heaters, auxiliary air-conditioning heating sections
6. Cabinet power distribution: Заменить реле + contactor combinations; quiet, arcless operation, Установка на DIN-рейку.

When to choose this SSR instead of electromagnetic contactors

Частое циклическое включение/выключение & PID power regulation (switching every several seconds)

Controlled by PLC or temperature controller DC24V transistor outputs

No arc noise, no contact burn-out & low maintenance required

DIN rail mounting with limited cabinet space, integrated heat sink included

Quick power cartridge replacement without full rewiring later

Неподходящий / Ограниченные приложения

Direct-on-line starting of large motors, frequently started pumps (high inrush current causes instant damage)

Capacitive loads, large switching power supply banks

400VAC loads (max rated voltage only 264VAC)

Нагрузки постоянного тока (this model is AC-output SSR only)

Circuits requiring short-circuit protection: SSR has no built-in short-circuit protection; fuse/circuit breaker must be installed upstream.

Sizing Tips

Derate to 48A when tightly mounted side-by-side (80% текущий рейтинг); always leave current margin.

Индуктивные нагрузки: Fit external 471K (470В, ≥1000A) varistor across output terminals, shortest wiring possible.

3-phase heating scheme: 3 independent G3PA-260B-VD, one per phase, keep 3-phase load balanced.

PID Power Regulation Wiring + Varistor Selection + Derating Installation Standard

Ключевое примечание: This is a zero-crossing SSR, designed exclusively for time-proportion PID power regulation, not for phase-angle voltage regulation. DC5~24V input, control current ≤7mA; PLC transistor outputs and temperature controller SSR ports can drive it directly without auxiliary relays.

1. PID Control Wiring (Контроллер температуры / ПЛК)

Определение терминала (G3PA-260B-VD)

Control Input: А1(+), А2(-) (DC5~24V; reverse polarity will not burn the unit, just no operation)

Выходная мощность: Line IN, Line OUT (series-connected on live wire, 24~240 В переменного тока)

Recommended wiring: MCB → semiconductor fast fuse → SSR output → Load → Neutral (N wire bypasses SSR entirely).

Схема 1: Driven by ОМРОН E5CC/E5EC Temperature Controller (Most Common Heating Loop)

1. SSR output of temperature controller → A1(+), А2(-) of G3PA
2. Separate power supply & PT100 thermocouple wiring
3. Critical parameter settings

Режим вывода: ССР / Time Proportion (Zero-cross); DO NOT select phase-angle mode

Время цикла (Т): 20~40s for resistive heating; 30s for ovens & mold heaters. Too short a cycle causes overheating; too long creates large temperature fluctuations.

Run AT auto-tuning after stable temperature holding.

Примечание: Open-collector outputs on temperature controllers have built-in 24VDC drive power, directly compatible with G3PA.

Схема 2: PLC Transistor DO Drive (ПНП / НПН)

ПНП-выход: PLC Y terminal → A1(+); 0V of 24VDC → A2(-)

NPN-выход: 24VDC+ → A1(+); PLC Y terminal → A2(-)

Программа ПЛК: Use fixed-cycle duty-cycle output (например. 30s period, 0~100%). Avoid high-frequency PWM which overheats the thyristor.

Only 7mA input current; standard PLC transistor outputs can drive it without current-limiting resistors.

3-phase Heating (3× G3PA-260B-VD)

Independent phase control: one single-phase SSR per A/B/C phase. Inputs can share multi-channel SSR outputs from one temperature controller or multiple PLC DO points.

⚠️ This is not a 3-phase SSR; только 3 separate single-phase units, keep load current balanced across 3 фазы.

2. Варистор & RC Snubber Selection (Mandatory for Inductive Loads)

The G3PA has an internal varistor, but inductive back EMF exceeds internal absorption capacity; external MOV is required, wired directly across SSR output terminals with minimal lead length.

220VAC System (Основное приложение)

Варистор: 14D471K (470В, ≥1000A surge current); 10D471K also acceptable.

110VAC System: 14D271K (270В, ≥1000A)

RC демпфер (for solenoid valves, маленькие фанаты & трансформаторы):

C=0.047~0.1μF / 630ВАК; R=100~220Ω / 2Вт, series RC across output terminals.

✅ Resistive heating tubes: External snubber optional; ✅ Fans, катушки & transformers will blow the SSR without external MOV.

Upstream Fuse Protection (Критический: SSR has no short-circuit protection)

Semiconductor SSR fails instantly under short-circuit conditions; use aR/gR semiconductor fast fuses, not standard gG general fuses.

Resistive heating loads: 80A fast fuse (1.2~1.5× rated current of 60A)

Inductive fan loads: 100A fast fuse

Install fuse immediately upstream of the SSR to shorten fault loop length.

3. Снижение номинальных характеристик & Характеристики установки (G3PA-260B-VD Special Rule)

The G3PA-260B-VD cannot be tightly mounted side-by-side (stated in official datasheet), different from 240B/220B models.

1. Full rating condition: Vertical independent mounting, ≥10mm clearance left & верно, ambient temp ≤40℃ → 60A full current.
2. Densely arranged on DIN rail:

2 or more units installed tightly together: Max current limited to 48A (80% снижение номинальных характеристик).

4+ units side-by-side: Maintain ≥10mm gap between adjacent SSRs, otherwise overheating failure occurs.

Вертикальная укладка: ≥80mm vertical gap between upper & lower SSRs to keep airflow.

3. Horizontal flat mounting (heat sink sideways): Derate current by an additional 30%; avoid this mounting orientation.
4. Cabinet ambient >40℃: Further derate current per temperature derating curve; add cabinet cooling fans.
5. Терминальный крутящий момент: Винтовые клеммы M3,5, tighten to 0.8~1.2N·m. Loose terminals cause overheating & сгоревшие клеммы.
6. Cartridge replacement: G3PA allows standalone replacement of the G32A power cartridge without rewiring main power circuits, ideal for bulk maintenance.
7. Commissioning Troubleshooting Checklist
8. Never use this zero-cross SSR for phase-angle dimming/power control; it only supports time-proportion ON/OFF power regulation.
9. Off-state leakage: ≤20mA residual voltage across load when SSR is OFF; always isolate upstream MCB before maintenance.
10. Do not add large series resistors on input side; low voltage will cause false triggering.
11. Separate DC24V control wiring from high-current power cables to avoid EMI interference.
12. Cold heating element inrush current: Limit heater rated current to ≤70% of SSR rated current for extra safety margin.
13. Quick Fault Diagnosis

Indicator ON, load no heat: Open circuit on main circuit, перегоревший предохранитель, broken heater element.

Indicator OFF: No input voltage/polarity reversed, temperature controller output disabled, PLC program no output.

Repeated SSR breakdown: No external MOV for inductive loads, insufficient heat dissipation, oversized fuses, frequent mains voltage surges.

Severe temperature oscillation: PID cycle time too short, P-gain too high, poor thermal insulation, thermocouple misposition.

OMRON Single-Phase SSR + Electromagnetic Power Relay List

Примечание: All SSRs are zero-crossing, оптоизолированный. G3PA series (ваша текущая модель) features replaceable power cartridges, integrated heat sink & Монтаж на DIN-рейку. G3NA/G3NE are cost-effective compact SSRs. Electromagnetic relays are plug-in cabinet relays for PLC & temperature control loops.

Часть 1: G3PA Series (Single-phase SSR, Priority Model)

Replaceable Power Cartridges

G32A-A20-VD-X: For G3PA-220B

G32A-A40-VD: For G3PA-240B

G32A-A60-VD: For G3PA-260B

Часть 2: G3NA Economy Single-phase SSR (No integrated heat sink)

Часть 3: G3NE Compact Mini SSR (Space-saving low-power use)

Часть 4: G3PJ / G3PE New Generation SSR (Spring terminals, high surge resistance)

G3PJ-225B: 24–240 В переменного тока, 25А, DC5–24V

G3PJ-245B: 24–240 В переменного тока, 45А, DC5–24V

G3PE-225B: 24–240 В переменного тока, 25А, DC5–24V

G3PE-245B: 24–240 В переменного тока, 45А, DC5–24V

Правило кодирования модели:

2 = AC24~240V (220V heating mainstream)

4 = AC200~400/480V high voltage

VD = DC input; A = AC input

Часть 5: OMRON Electromagnetic Power Relays (Plug-in cabinet type)

1. G2R Series (General-purpose Intermediate Relays)

2. LY High-current Plug-in Power Relays (Replace small contactors)

3. G7L High-capacity Power Relays (30A direct single-phase load control)

4. G6B / G6D PCB Mini Relays (Onboard PLC & регуляторы температуры)

G6B-1174P: 1а, 5А, 24 В постоянного тока

G6D-1A: 1а, 5А, 24 В постоянного тока

Часть 6: Руководство по выбору: SSR vs Electromagnetic Relay

1. Обогрев, PID power regulation, частое переключение & arcless operation → G3PA (Первый выбор) / G3NA
2. PLC DO signal conversion, low-frequency switching → G2R intermediate relay
3. ≤30A low-frequency single-phase loads, cost-sensitive → G7L / LY relays
4. Low-power, space-restricted applications → G3NE, G3PJ