SMC IP8000 ตัวกำหนดตำแหน่งวาล์วไฟฟ้า-นิวแมติก - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

วีแชท: +86-13184948252 วอทส์แอพพ์: 0086-13811255435 อีเมล: kent@bestcontactor.com

เกี่ยวกับ ติดต่อ |

SMC IP8000 ตัวกำหนดตำแหน่งวาล์วไฟฟ้า-นิวแมติก - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

ไฟฟ้า/

SMC IP8000 ตัวกำหนดตำแหน่งวาล์วไฟฟ้า-นิวแมติก

The IP8000 is a classic SMC mechanical E/P electro-pneumatic positioner (non-smart, ไม่มีฮาร์ท). It is designed for linear-stroke pneumatic diaphragm actuators. It receives a 4~20mA current signal and converts it into supply air pressure to drive control valves. It replaces the older IP6000 series. The IP8100 in the same series is for rotary-stroke applications. ที่ ...

  • รายละเอียดสินค้า

The IP8000 is a classic SMC mechanical E/P electro-pneumatic positioner (non-smart, ไม่มีฮาร์ท). It is designed for linear-stroke pneumatic diaphragm actuators. It receives a 4~20mA current signal and converts it into supply air pressure to drive วาล์วควบคุม. It replaces the older IP6000 series. The IP8100 in the same series is for rotary-stroke applications. The IP8001/IP8101 are smart versions with auto-tuning and share the same housing.

✅ ข้อมูลจำเพาะทางเทคนิคที่สำคัญ

รายการIP8000 (ประเภทคันโยก)
สัญญาณอินพุตDC 4~20mA, ความต้านทานอินพุต: 235±15Ω
Supply Air Pressure0.14~0.7 เมกะปาสคาล
Applicable Stroke10~85mm (linear valve stem)
ความแม่นยำSensitivity ≤0.1%FS; Linearity ±1%FS; Hysteresis ≤0.75%FS; การทำซ้ำ ±0.5%FS
การป้องกันทางเข้าIP65 (IEC60529)
อุณหภูมิแวดล้อม-20~80℃ for standard model; ExdⅡBT5 explosion-proof: -20~60℃
Air PortsRC1/4 / G1/4 / 1/4เอ็นพีที; Gauge port Rc1/8
การเชื่อมต่อไฟฟ้าG1/2, M20×1.5, 1/2NPT optional
ความต้านทานการสั่นสะเทือนNo resonance within 5~200Hz
มาตรฐานการติดตั้งCompliant with NAMUR, DIN/IEC 60534-6-1 วงเล็บ

📌 คำจำกัดความของรหัสรุ่น (IP8000-□□□)

IP8000: Lever-type mechanical electro-pneumatic positioner

  1. Pressure gauge specification: 0=0.3MPa, 3=1.0MPa
  2. การก่อสร้าง: Standard housing / ExdⅡBT5 explosion-proof terminal box
  3. เครื่องประดับ: Restrictor pilot valve, yoke linkage, extended feedback lever, ฯลฯ.
  4. Thread type, CE marking, special custom codes (เช่น. X310=IP66)

🛠 Working Principle & แนวทางการติดตั้ง

  1. หลักการ: A 4~20mA current energizes the torque motor. The nozzle-flapper amplifies the signal to control the output air pressure of the pilot valve. The feedback lever captures the actual valve stem position to form a closed loop, ensuring valve position matches the input signal.
  2. Key Installation Rule: ที่ 50% สัญญาณ (12มิลลิแอมป์), the feedback lever should form a 90° right angle with the valve stem. Select the internal feedback spring according to single-acting or double-acting actuators.
  3. การปรับ: Mechanical Zero and Span knobs. Supports split range operation. Equipped with manual/auto switching screw for manual air supply during commissioning.

⚠️ การแก้ไขปัญหาทั่วไป

  1. Valve fails to move

No supply air or insufficient air pressure; 4~20mA wiring reversed; nozzle/restrictor blocked by dust; torque motor damaged.

  1. Oscillation / การล่าสัตว์

Incorrect feedback lever mounting angle; unstable supply air pressure; stuck pilot valve; excessive friction of valve packing.

  1. Poor linearity / ศูนย์ดริฟท์

Zero/span not calibrated; loose feedback linkage; air piping leakage; large ambient temperature variation.

  1. Insufficient output pressure

Foreign matter jamming pilot valve; leaking actuator diaphragm/cylinder; clogged air filter.

Maintenance Reminder: Cut off air supply and fully vent pressure before disassembly. ทำความสะอาดปากหัวฉีดด้วยลวดละเอียด 0.2 มม. ทาจาระบีซิลิโคน TORAY SH45 เบา ๆ เมื่อประกอบโอริง.

📋 การเลือกรุ่น & ทางเลือก

IP8000: เครื่องกล, คันโยกจังหวะเชิงเส้น. สำหรับวาล์วควบคุมแบบธรรมดา, ต้นทุนต่ำ, ไม่มีการสื่อสาร.

IP8100: เครื่องกล, ลูกเบี้ยวหมุน, สำหรับวาล์วปีกผีเสื้อและบอลวาล์ว.

IP8001: จังหวะเชิงเส้นอัจฉริยะ. การสอบเทียบอัตโนมัติ, ฮาร์ท, การวินิจฉัยข้อบกพร่อง, อัพเกรดทดแทนสำหรับ IP8000.

ทางเลือกภายในประเทศ: ผู้กำหนดตำแหน่ง E/P ในประเทศ เช่น Wuzhong และ Chuanyi. ตรวจสอบวงเล็บ, พอร์ตอากาศและการจับคู่จังหวะ.

📎 สถานการณ์การใช้งานทั่วไป

การควบคุมการไหลอย่างต่อเนื่อง, ความดันและระดับของวาล์วควบคุมไดอะแฟรมนิวแมติกเชิงเส้นในทางเคมี, การบำบัดน้ำ, เครื่องปรับอากาศ, กระดาษ, น้ำมัน & ท่อส่งก๊าซ. รุ่นป้องกันการระเบิด ExdⅡBT5 มีจำหน่ายในพื้นที่อันตราย.

SMC IP8000 ตัวกำหนดตำแหน่งวาล์วไฟฟ้า-นิวแมติก — สถานการณ์การใช้งาน

IP8000 เป็นตัวกำหนดตำแหน่ง E/P แบบกลไกจังหวะเชิงเส้นที่เข้าคู่กับวาล์วควบคุมนิวแมติกเชิงเส้นของไดอะแฟรม. It converts 4~20mA analog signal into air pressure to drive valve stem for continuous process regulation. No HART communication.

🏭 Industry Applications

  1. น้ำ / การบำบัดน้ำเสีย

Inlet flow regulation, pH dosing line, การควบคุมระดับของเหลว, aeration pressure regulation. Standard non-explosion model is sufficient; IP65 preferred for outdoor installation.

  1. เครื่องปรับอากาศ & Heating Networks

Temperature control for primary/secondary side of heat exchangers, regulating steam/hot water linear control valves.

  1. อุตสาหกรรมกระดาษ

Pulp concentration control, white water flow, steam pressure regulation. Dust-prone workshop; air filtration is mandatory to prevent nozzle blockage.

  1. อุตสาหกรรมเคมี (Use ExdⅡBT5 explosion-proof IP8000 for hazardous zones)

การควบคุมการไหลอย่างต่อเนื่อง, pressure and level in process pipelines. Explosion-proof housing required for solvents and light hydrocarbon hazardous areas.

บันทึก: IP8000 is mechanical without smart diagnosis. Use IP8001 if HART and auto-tuning are required.

  1. อาหาร & เครื่องดื่ม / เภสัชกรรม (Sanitary Service)

น้ำบริสุทธิ์, wash water and steam regulation, paired with sanitary linear control valves. Prefer clean instrument air.

  1. พลัง & โรงไฟฟ้าพลังความร้อน

Boiler feedwater, desuperheating and pressure reduction, condensate level control; auxiliary process control valves.

  1. น้ำมัน & Gas Storage & การขนส่ง (Explosion-proof Version)

Pressure and flow regulation for crude/product pipelines, tank level control. Exd explosion-proof model for explosive hazardous areas.

✅ Suitable Valve Types

Single-acting / double-acting linear pneumatic diaphragm control valves (best match)

Cage guided valves, single-seat valves, cage control valves

❗ Butterfly valves, ball valves and other rotary valves require IP8100, IP8000 is not applicable.

📌 Application Characteristics

ประเภทการควบคุม: Continuous modulating (not on/off valve). 4~~20mA corresponds to 0~~100% valve travel.

Air source: ทำความสะอาด, แห้ง, oil-free compressed air. ตัวควบคุมตัวกรองอากาศ (เอเอฟอาร์) จะต้องติดตั้งต้นน้ำ.

ข้อดี: โครงสร้างที่เรียบง่าย, บำรุงรักษาง่าย, ประสิทธิภาพการป้องกัน EMI ที่ดี. เหมาะสำหรับไซต์ที่ไม่มีข้อกำหนดในการสื่อสารด้วยบัสและมีงบประมาณจำกัด.

ข้อจำกัด: การตอบสนองทางกล, ไม่มีการสอบเทียบอัตโนมัติ. จำเป็นต้องปรับค่าศูนย์และช่วงแบบแมนนวล; ไม่มีการวินิจฉัยข้อผิดพลาด.

❌ ไม่แนะนำสถานการณ์

  1. การสั่นอย่างรุนแรง, ก๊าซที่มีฤทธิ์กัดกร่อนรุนแรง (จำเป็นต้องมีการป้องกันที่อยู่อาศัยเพิ่มเติม).
  2. การวินิจฉัยระยะไกล, การสื่อสารฮาร์ต, ต้องปรับอัตโนมัติ → อัปเกรดเป็น IP8001.
  3. ผีเสื้อโรตารี / บอลวาล์ว → เลือก IP8100.
  4. ฝุ่นหนัก, อากาศเครื่องมือที่ไม่บริสุทธิ์ (มีความเสี่ยงสูงที่จะเกิดการอุดตันของหัวฉีด).

SMC IP8000 — รายการตรวจสอบการเลือก

ใช้ได้กับตัวกำหนดตำแหน่งอิเล็กโทรนิวเมติกเชิงกลเชิงเส้น IP8000; ใช้ IP8100 สำหรับการใช้งานแบบโรตารี่; รุ่นอัจฉริยะ IP8001 มีกฎการเลือกแยกต่างหาก.

  1. แอคชูเอเตอร์ & ข้อมูลพื้นฐานของวาล์ว
ตรวจสอบรายการข้อกำหนดในการคัดเลือก & หมายเหตุ
ประเภทแอคชูเอเตอร์ตัวกระตุ้นนิวแมติกไดอะแฟรมจังหวะเชิงเส้น (การแสดงเดี่ยว / การแสดงสองครั้ง). ไม่ใช่สำหรับวาล์วปีกผีเสื้อ/บอลวาล์วแบบหมุน.
จังหวะก้านวาล์ว10~85mm; ยืนยันจังหวะที่เกิดขึ้นจริง. Out-of-range travel invalid; too small stroke degrades feedback lever accuracy.
Actuator Action□ Single-acting (ฤดูใบไม้ผลิกลับมา), replace internal feedback spring inside positioner
□ Double-acting (no spring, bidirectional air supply), replace internal feedback spring
ประเภทวาล์วSingle-seat / cage / cage-guided modulating control valves; modulating service, not on/off valve
Stem Diameter & Mount BracketDIN/IEC 60534-6-1 / NAMUR standard. Verify feedback linkage and yoke accessories. Excessive stem wobble causes oscillation.
  1. กระบวนการ & สภาพการทำงาน
ตรวจสอบรายการข้อกำหนดในการคัดเลือก & หมายเหตุ
Process Mediaน้ำ, ไอน้ำ, อากาศ, general chemical fluids. Evaluate housing protection for highly corrosive media.
Explosion-proof Requirement□ Standard non-explosion (safe area)
□ ExdⅡBT5 explosion-proof (พื้นที่อันตราย, ขีด จำกัด อุณหภูมิ: -20~60℃; standard model -20~80℃)
อุณหภูมิแวดล้อมมาตรฐาน: -20℃ ~ +80 ℃; ป้องกันการระเบิด: -20℃ ~ +60 ℃. Heat insulation required for over-temperature sites.
Enclosure Protectionมาตรฐาน IP65; IP66 optional (suffix X310). IP65+ recommended for outdoor, สภาพแวดล้อมที่ชื้นและมีฝุ่นมาก.
การสั่นสะเทือนNo resonance from 5~200Hz. Reinforce linkage under heavy vibration to avoid continuous hunting.
Control Requirement4~20mA analog continuous modulation; No HART, no auto-tuning. Manual zero/span calibration needed.
  1. Air Supply System Check (Highest Failure Source)
ตรวจสอบรายการข้อกำหนดในการคัดเลือก & หมายเหตุ
Supply Pressure Range0.14~0.7 เมกะปาสคาล. Stable pressure; pressure fluctuation easily triggers valve oscillation.
Air Qualityแห้ง, ทำความสะอาด, oil-free compressed air. Pre-install air filter regulator (เอเอฟอาร์) to remove water, oil and dust. Dust environment easily clogs nozzle.
Air Port ThreadG1/4 / RC1/4 / 1/4เอ็นพีที; gauge port Rc1/8. Confirm thread before ordering.
  1. Electrical Check
ตรวจสอบรายการข้อกำหนดในการคัดเลือก & หมายเหตุ
สัญญาณอินพุตDC 4~20mA; ความต้านทานอินพุต 23515. Match signal source load capacity.
Electrical EntryG1/2 / M20*1.5 / 1/2เอ็นพีที. Explosion-proof model requires explosion-proof cable gland.
สายไฟ2-wire 4-20mA. Polarity matters; reversed polarity causes no operation. Shielded cable recommended for long distance, single-end grounding.
  1. Auxiliary Accessories Selection

□ Pressure gauge: 0=0.3MPa, 3=1.0MPa (select based on output pressure range)

□ คันตอบรับ, yoke linkage (จับคู่กับจังหวะแอคชูเอเตอร์)

□ ตัวควบคุมตัวกรองอากาศ, ท่ออากาศ

□ ตัวยึดและตัวยึด

□ เคเบิลแกลนด์ป้องกันการระเบิด (จำเป็นสำหรับรุ่นป้องกันการระเบิด)

  1. เกณฑ์การยกเว้น (อย่าเลือก IP8000 หากมี)
  2. โรตารี่วาล์ว (ผีเสื้อ / วีบอลวาล์ว) → ใช้ IP8100
  3. การสื่อสารฮาร์ต, การวินิจฉัยระยะไกล, ต้องปรับอัตโนมัติ → ใช้ IP8001
  4. แหล่งอากาศที่ไม่บริสุทธิ์ซึ่งมีฝุ่นหนามาก, น้ำมันและคอนเดนเสท
  5. จังหวะวาล์ว >85มม. หรือ <10มม
  6. การกัดกร่อนอย่างหนัก, การสั่นสะเทือนที่รุนแรงโดยไม่มีมาตรการป้องกัน
  7. ตัวอย่างการเลือก (การอ้างอิงรหัสรุ่น)

IP8000-3 (1.0เกจ MPa) + ป้องกันการระเบิด + พอร์ตอากาศ G1/4 + M20 ทางเข้าไฟฟ้า

IP8000-301: 1.0เกจ MPa, ที่อยู่อาศัยมาตรฐาน, ชุดประกอบคันโยกมาตรฐาน

  1. การตรวจสอบก่อนการติดตั้ง
  2. ท่อลมถูกไล่ออกจนหมดเพื่อขจัดตะกรันและเศษจากการเชื่อม.
  3. คันตอบรับใกล้ 90° ที่ 50% สัญญาณ (12มิลลิแอมป์).
  4. ไม่มีการรั่วไหลของแอคชูเอเตอร์; แรงเสียดทานของการบรรจุจะต้องไม่มากเกินไป.
  5. สายดินหุ้มฉนวน; แยกเส้นทางออกจากสายไฟเพื่อหลีกเลี่ยงการรบกวน VFD.

SMC IP8000 Electro-Pneumatic Valve Positioner — Maintenance Manual

Applicable to IP8000 mechanical linear E/P positioner; Pre-work safety: Disconnect 4~20mA signal, shut off air supply and vent pressure. Never open housing under pressure.

  1. ช่วงเวลาการบำรุงรักษา (รายวัน / รายไตรมาส / ประจำปี)

1) Daily Routine Inspection (per shift / daily visual check)

  1. Check housing for air leakage, การควบแน่น, corrosion and loose fittings.
  2. Observe two pressure gauges for stable readings; watch for fluctuation/hunting.
  3. Check valve stem movement: smooth travel, ไม่ติดหรือมีเสียงรบกวนผิดปกติ.
  4. Drain condensate from air filter regulator in a timely manner.
  5. Check mounting bracket, feedback linkage and bolts for looseness.

Warning sign: Gauge needle jumping continuously, valve hunting → inspect feedback mechanism or nozzle blockage first.

2) การบำรุงรักษารายไตรมาส (ทั้งหมด 3 เดือน)

  1. Inspect filter element of air filter regulator; replace if contaminated.
  2. Check feedback lever, yoke and pin shafts: apply minimal grease (อย่าหล่อลื่นมากเกินไป! ไขมันส่วนเกินดักจับฝุ่นและหัวฉีดอุดตัน).
  3. ขันฮาร์ดแวร์ให้แน่น: สลักเกลียวยึดตำแหน่ง, อุปกรณ์ท่อและเทอร์มินัลบล็อก.
  4. การทดสอบการทำงาน: อินพุต 4mA, 12มิลลิแอมป์, 20มิลลิแอมป์, บันทึกค่าเบี่ยงเบนเป็นศูนย์และช่วง.
  5. ตรวจสอบสายเคเบิลและต่อมสายเคเบิล; ตรวจสอบให้แน่ใจว่ามีการปิดผนึกครบถ้วน, ไม่มีน้ำเข้า.

3) ยกเครื่องประจำปี (ปีละครั้ง; ทั้งหมด 6 เดือนภายใต้สภาวะที่ไม่เอื้ออำนวย)

  1. ถอดชิ้นส่วนหน่วย, ที่อยู่อาศัยภายในสะอาด, มุ่งเน้นไปที่หัวฉีด, ลูกนกและตัวจำกัดวาล์วนำร่อง (จุดล้มเหลวสูงสุด).
  2. ถอดประกอบและตรวจสอบโอริง; เปลี่ยนชุดซีลเต็มหากมีอายุ, แข็งหรือแตก.
  3. ตรวจสอบขดลวดมอเตอร์ทอร์คว่ามีสีเปลี่ยนไปจากความร้อนสูงเกินไปหรือไม่; ตรวจสอบช่องว่างหัวฉีด-ลูกนก.
  4. ปรับเทียบศูนย์และสแปนอีกครั้ง, บันทึกข้อมูลการสอบเทียบ.
  5. ตรวจสอบท่ออากาศ; เปลี่ยนท่อเก่า.
  6. ตรวจสอบเพิ่มเติมสำหรับรุ่นป้องกันการระเบิด: พื้นผิวรอยต่อระเบิดไม่เสียหาย, ปะเก็นไม่บุบสลาย, สอดคล้องกับช่องว่างที่ทนไฟ.

บริการที่รุนแรง (ฝุ่น, ความชื้น, น้ำเสีย, กระดาษ): ลดระยะเวลาการบำรุงรักษาลงครึ่งหนึ่ง.

  1. การบำรุงรักษาส่วนประกอบสำคัญ

✅หัวฉีด & ลูกนก (แหล่งที่มาของข้อผิดพลาดที่พบบ่อยที่สุด)

  1. การทำความสะอาด: ใช้ลวดไนลอน/ทองแดงละเอียด 0.2 มม. เพื่อค่อยๆ ล้างช่องหัวฉีด. อย่าเกาพื้นผิวหัวฉีดด้วยลวดเหล็กแข็ง.
  2. เป่าฝุ่นด้วยลมอัดแห้งที่ความดันต่ำ (≤0.2MPa). ห้ามล้างตัวกำหนดตำแหน่งภายในด้วยของเหลว.
  3. พื้นผิวบานกระทุ้งปราศจากรอยขีดข่วนและการปนเปื้อนของน้ำมัน. รอยขีดข่วนทำให้เกิดการล่าสัตว์อย่างต่อเนื่อง; เปลี่ยนชุดประกอบลิ้นปีกนกหัวฉีด.
  4. ความต้องการ: อากาศในเครื่องมือต้องแห้งและปราศจากน้ำมัน. ฟิล์มน้ำมันบนแผ่นปีกหัวฉีดทำให้เกิดการดริฟท์และการสั่น.

✅ ชุดประกอบคันป้อนกลับ

  1. ใช้สารหล่อลื่นเพียงเล็กน้อยกับสลักเพลาและเดือย; ไม่มีจาระบีหนัก.
  2. ตรวจสอบการเชื่อมโยงเพื่อดูการเสียรูป; ไม่ติดขัดระหว่างการเคลื่อนตัวของก้าน.
  3. ที่ 50% สัญญาณ (12มิลลิแอมป์), คันโยกควรอยู่ใกล้ 90°. ปรับการติดตั้งใหม่หากมุมเบี่ยงเบนไปมาก.

✅ซีล (โอริง)

โอริงมีอายุและแข็งตัวภายใต้ความผันผวนของอุณหภูมิที่สูงและการทำงานต่อเนื่อง.

Apply thin layer of TORAY SH45 silicone grease when replacing O-rings, avoid over-application.

Prevent scratches on O-ring grooves during assembly.

✅ Electrical Section

  1. Inspect 4~20mA 2-wire terminals for oxidation and looseness; การต่อสายดินปลายด้านเดียวสำหรับสายเคเบิลที่มีฉนวนหุ้ม.
  2. Explosion-proof model: power cut before cover removal. Do not damage flameproof mating surface; seal gasket and cable gland must remain sealed.
  3. Separate signal cables from power cables to avoid VFD interference.
  4. Long-Term Shutdown Preservation (Out of service >1 month)
  5. Shut off air supply and vent pressure; disconnect 4-20mA signal.
  6. Set valve to mid-position (50% เปิด) to reduce long-term single-side spring stress.
  7. Drain condensate from air filter.
  8. Cover housing for dust protection to avoid dust accumulation on nozzle-flapper.
  9. Purge air piping and re-calibrate zero & span before recommissioning.
  10. การดำเนินการต้องห้าม (คำเตือนที่สำคัญ)

❌ Open positioner housing under pressure or powered condition

❌ Blast nozzle-flapper assembly with high-pressure compressed air

❌ Apply large amount of grease (traps dust and clogs nozzle)

❌ Flush internal parts with liquid (only wipe housing exterior with damp cloth)

❌ Force feedback lever; may deform torque motor and cam

❌ Use instrument air with oil, water and heavy contaminants

  1. Post-Maintenance Verification Procedure

Follow sequence after maintenance:

  1. Apply air supply, verify all air joints leak-free.
  2. Connect 4~20mA signal generator.
  3. 4mA → zero calibration; 20mA → span calibration; repeat 2~3 cycles.
  4. Test linearity at midpoint 12mA; confirm no oscillation or lag.
  5. Record calibration data and file maintenance log.
  6. Quick Fault Reference During Maintenance
  7. Valve hunting / small cycling: หัวฉีด/ลูกนกสกปรก; มุมคันโยกข้อเสนอแนะที่ไม่ถูกต้อง; อากาศที่จ่ายไม่เสถียร.
  8. ศูนย์ดริฟท์: ควบแน่นในอากาศ; การรั่วไหลของโอริงเล็กน้อย; การอุดตันของหัวฉีดเล็กน้อย.
  9. Insufficient output pressure: วาล์วนักบินติดอยู่; clogged air filter.
  10. ฮิสเทรีซิสขนาดใหญ่: พีวอทติดและมีแรงเสียดทานสูง; แรงเสียดทานการบรรจุมากเกินไปของแอคชูเอเตอร์.

ก่อนหน้า:

ต่อไป:

ทิ้งคำตอบไว้

ฝากข้อความ