UNI-T UT81B Oscilloscope Multimeter - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

วีแชท: +86-13184948252 วอทส์แอพพ์: 0086-13811255435 อีเมล: kent@bestcontactor.com

เกี่ยวกับ ติดต่อ |

 UNI-T UT81B Oscilloscope Multimeter - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

มิเตอร์ไฟฟ้า/

UNI-T UT81B Oscilloscope Multimeter

สถานะ: Discontinued Old monochrome, single-channel oscilloscope multimeter (oscilloscope + multimeter 2-in-1). Do not confuse it with the new colour dual-channel UT81B+. Oscilloscope Specifications Bandwidth: 8 MHz Real-time sampling rate: 40 MSa/s Vertical sensitivity: 20 mV/div ~ 500 V/div (1-2-5 ลำดับ) Vertical accuracy: ±(5%+1) Timebase accuracy: ±(0.01%+1) คุณสมบัติ: Auto setup, waveform storage, USB waveform upload to ...

  • รายละเอียดสินค้า

สถานะ: ยกเลิก

Old monochrome, single-channel oscilloscope มัลติมิเตอร์ (oscilloscope + multimeter 2-in-1). Do not confuse it with the new colour dual-channel UT81B+.

  1. Oscilloscope Specifications

แบนด์วิธ: 8 เมกะเฮิรตซ์

Real-time sampling rate: 40 MSa/s

Vertical sensitivity: 20 mV/div ~ 500 V/div (1-2-5 ลำดับ)

Vertical accuracy: ±(5%+1)

Timebase accuracy: ±(0.01%+1)

คุณสมบัติ: Auto setup, waveform storage, USB waveform upload to PC, trigger adjustment

  1. DMM Multimeter Specifications (3999 counts)

DCV: 400 mV ~ 1000 วี, accuracy ±(0.8%+8)

เอซีวี: 4 วี~ 750 วี, accuracy ±(1%+15)

DCA: 400 μA ~ 10 ก, accuracy ±(1%+8)

ACA: 400 μA ~ 10 ก, accuracy ±(1.5%+8)

ความต้านทาน: 400 Ω ~ 40 MΩ, ±(1%+5)

ความจุ: 40 nF ~ 100 ไมโครเอฟ, ±(3%+8)

Extra functions: Diode test, เสียงบี๊บต่อเนื่อง, ความถี่, duty cycle (0.1%~99.9%)

  1. การเปรียบเทียบแบบจำลอง (Critical to avoid mistakes)
แบบอย่างOscilloscope Channelsแบนด์วิธแสดงสถานะ
UT81Bช่องเดียว8 เมกะเฮิรตซ์Monochrome LCDยกเลิก
UT81Cช่องเดียว16 เมกะเฮิรตซ์Monochrome LCDยกเลิก
UT81B+ช่องคู่100 เมกะเฮิรตซ์ColourActive new model, with signal generator
  1. การใช้งาน & ข้อจำกัด

✅เหมาะสำหรับ: Simple waveform inspection in industrial control, power supply ripple, รีเลย์ / low-frequency inverter signals, appliance repair, portable on-site commissioning

❌ข้อจำกัด: ช่องเดียว, low bandwidth, monochrome screen, no built-in signal generator, ยกเลิกแล้ว. For high-frequency or dual-channel requirements, choose UT81+ series.

  1. อินเทอร์เฟซ & เครื่องประดับ

ขั้วอินพุต: 10ก, mA/μA, คอม, SCOPE (BNC for oscilloscope)

การสื่อสาร: ยูเอสบี, bundled PC software for waveform export

แหล่งจ่ายไฟ: Battery-powered handheld unit

  1. การอ้างอิงการเลือกทางเลือก

If you need a replacement for the UT81B:

Similar handheld oscilloscope multimeter: UT82B (50 เมกะเฮิรตซ์, ช่องทางเดียว)

ช่องคู่ + signal generator: UT81C+ / UT81D+

UNI-T UT81B (Old Monochrome Model) Practical Tutorial Collection

คำเตือนที่สำคัญ: Most online videos cover the UT81B+ (new colour dual-channel version). Its buttons and menus are different from this discontinued old UT81B. All content below applies to the old single-channel UT81B, for industrial repair, อินเวอร์เตอร์, power ripple and relay signal debugging.

  1. Document Tutorials (Authoritative, priority reading)
  2. Original factory English manual (UT81A/B)

Covers button definitions, menus, ranges, triggering, cursors, การสื่อสารผ่านยูเอสบี, battery and fuse replacement. It is the only official document for this meter. Search PDF with keyword: `UT81A/B OPERATING MANUAL`

It fully describes: MODE toggle between multimeter DMM and oscilloscope SCOPE, AUTO setup, AUTO/NORM/SHOT trigger modes, waveform storage (สูงสุด 10 ชุด), backlight and contrast settings.

  1. Third-party notes (industrial community)

Search keyword: `UT81B handheld oscilloscope multimeter repair notes`. Many appliance and inverter repair technicians share practical cases: measuring switching power supply ripple, PWM drive waveforms, relay pull-in chatter.

  1. Step-by-step Practical Tutorials

✅ Tutorial 1: Basic switching + probe compensation (mandatory first step)

  1. สายไฟ: Connect BNC oscilloscope probe to the SCOPE port. Attach the black clip to circuit ground, hook the probe tip to the test point. Set the probe to ×1 or ×10, and match the attenuation setting in the menu.
  2. เปิดเครื่อง. Press MODE to switch between [DMM Multimeter Mode] ↔ [SCOPE Oscilloscope Mode].
  3. Enter oscilloscope mode, press AUTO: auto-adjust vertical range, timebase and trigger. Always use AUTO for unknown signals.
  4. Probe compensation: The old UT81B has no built-in calibration square wave! You need a signal source or known standard square wave to calibrate the probe, otherwise waveform edges will be distorted.

✅ Tutorial 2: Core Oscilloscope Menus (UT81B monochrome menu)

RANGE menu: F1 move waveform up / F2 move waveform down / F3 increase V/div / F4 decrease V/div

BASE menu: F1 move waveform left / F2 move waveform right / F3 increase timebase s/div / F4 decrease timebase

TRIG trigger menu: อัตโนมัติ (baseline runs without valid signal), NORM (waveform only appears when trigger condition is met), SHOT single capture (for pulses and transient spikes, very useful for industrial work); F1/F2 adjust trigger level, rising / falling edge

MEAS cursor measurement: Enable cursors to manually read peak-to-peak value and period. The old UT81B has no automatic measurement readout, all values must be calculated manually with cursors — this is the biggest difference from UT81B+.

SAVE: Store waveforms, ขึ้นไป 10 screens for later recall

SYSTEM: แสงไฟ, beeper, auto power-off, ตัดกัน

✅ Tutorial 3: USB PC waveform upload tutorial (common pain point)

  1. Matching legacy software: UT81 series PC software (not compatible with new UT81+ software)
  2. Connect USB cable between PC and UT81B, switch the meter to oscilloscope mode
  3. Select the corresponding COM port in software, read waveforms, save screenshots and export data

Pitfall: วิน10 / Win11 often lacks the old USB-to-serial driver, CH340 driver is required; compatibility is poor on Win11.

✅ Tutorial 4: High-frequency industrial application scenarios

  1. Switching power supply ripple measurement

การมีเพศสัมพันธ์: AC coupling (remove DC offset), timebase 20 μs ~ 100 ไมโครวินาที, vertical setting 20 mV/div. Keep the ground clip lead as short as possible to reduce interference. Bandwidth limit 8 เมกะเฮิรตซ์, high-frequency ripple cannot be measured accurately.

  1. Inverter PWM and relay pull-in waveform

Use SHOT single-shot trigger to capture transient spikes at power-on; select rising edge triggering. Pay attention to common ground to avoid damaging the meter.

  1. Switch between multimeter and oscilloscope

Press MODE back to DMM to measure voltage, resistance or capacitance without changing instruments, convenient for on-site troubleshooting.

✅ Tutorial 5: Common troubleshooting

Waveform drifting, hard to trigger: Switch to NORM trigger, adjust trigger level manually, verify solid ground connection

Waveform amplitude too small: Check that probe attenuation matches menu setting (×10 probe without menu setting will give 10× reading error)

AUTO function fails: AUTO does not work when timebase >50 นางสาว, parameters must be adjusted manually

Dim screen: Adjust contrast in SYSTEM menu

  1. Video Search Tips (Avoid mixing models)

Search on Bilibili / Douyin with these keywords to distinguish old and new versions:

  1. ที่ต้องการ: `Old UT81B monochrome oscilloscope multimeter demo`
  2. ทางเลือก: `UT81C handheld oscilloscope tutorial` (UT81C shares nearly identical menu logic with UT81B, เท่านั้น 16 MHz bandwidth, suitable for reference)

❌ Do NOT search: `UT81B+`, interface and buttons are completely different and will confuse you.

General oscilloscope theory videos are applicable; vertical scale, timebase and trigger principles are universal.

  1. Learning Roadmap
  2. Read the original manual first and get familiar with buttons and menus (the monochrome UI has limited text and is confusing for new users)
  3. Practice with 50 Hz mains waveform to master AUTO, triggering and cursors
  4. Learn SHOT single capture (most valuable for industrial troubleshooting)
  5. Finally practise USB waveform upload to PC

ก่อนหน้า:

ทิ้งคำตอบไว้

ฝากข้อความ