Siemens 6EP1437-2BA10 Industrial Power Supply - คอนแทคเตอร์,เบรกเกอร์,อินเวอร์เตอร์พลังงานแสงอาทิตย์,มิเตอร์ไฟฟ้า,แบตเตอรี่พลังงานแสงอาทิตย์

วีแชท: +86-13184948252 วอทส์แอพพ์: 0086-13811255435 อีเมล: kent@bestcontactor.com

เกี่ยวกับ ติดต่อ |

 Siemens 6EP1437-2BA10 Industrial Power Supply - คอนแทคเตอร์,เบรกเกอร์,อินเวอร์เตอร์พลังงานแสงอาทิตย์,มิเตอร์ไฟฟ้า,แบตเตอรี่พลังงานแสงอาทิตย์

ข่าวข่าวการค้า

Siemens 6EP1437-2BA10 Industrial Power Supply

Siemens 6EP1437-2BA10 SITOP POWER 40 สามเฟส พาวเวอร์ซัพพลายอุตสาหกรรม

  1. รายละเอียดรหัสรุ่น

6EP1437-2BA10

6อีพี: Standard industrial power supply series of SITOP

1437: High-power three-phase AC model, 40A output platform

2: Basic standard version (without redundant diagnostic interface)

ปริญญาตรี: การติดตั้งราง DIN, 24เอาต์พุต VDC

10: 3-phase 400–500V input, 40ก / 960W output specification

  1. พารามิเตอร์ทางไฟฟ้าหลัก

ด้านอินพุต (3-Phase Industrial Grid)

Input format: 3×400~500V AC, 3-phase 5-wire L1/L2/L3/PE

ความถี่: 50/60เฮิรตซ์

Voltage dip tolerance: Minimum 340V for 2 seconds without output collapse

Wire gauge for input terminals: 0.5~4mm² solid/stranded copper wire

Output Side (Standard Industrial 24VDC)

จัดอันดับเอาท์พุท: 24กระแสตรง / 40ก, total power 960W

Adjustable output voltage range: 22.8~26.4V (tweaked via potentiometer at bottom)

ระลอกคลื่น & เสียงรบกวน: Ripple <150mVpp, peak noise <240mVpp

Output terminals: Dual groups of +/terminals for parallel connection; wire gauge 0.5~10mm²

Parallel expansion: Two identical units can be directly paralleled for max. 80เอาท์พุท

ฟังก์ชั่นการป้องกัน (Full-condition Protection)

  1. ป้องกันการลัดวงจร: Automatic hiccup current limiting, auto-recovery after fault clearance
  2. การป้องกันแรงดันไฟฟ้าเกิน (OVP): Output cut-off when voltage >27V
  3. การป้องกันการโอเวอร์โหลด (OLP): Current limiting at 120% จัดอันดับปัจจุบัน
  4. การป้องกันอุณหภูมิเกิน (OTP): Shutdown on overheat, auto-restart after cooling down
  5. Protection against input phase loss, surge and industrial EMC interference

III. เครื่องกล & ข้อมูลจำเพาะด้านสิ่งแวดล้อม

การติดตั้ง: Vertical installation on standard 35mm DIN rail

ขนาดโดยรวม (กว้าง × สูง × ลึก): 160 × 125 × 121 มม

น้ำหนักสุทธิ: ประมาณ. 2.0 กก

ระดับการป้องกัน: IP20 (for cabinet installation only)

อุณหภูมิในการทำงาน: 0~+55°C (full power derating required above 55°C)

พื้นที่จัดเก็บ / อุณหภูมิการขนส่ง: -25℃~+85℃

ความชื้น: 5%~95%RH, ไม่มีการควบแน่น

การรับรอง: ซีอี, แอล, GL marine certification; compliant with EN61010, EN61000 industrial EMC standards

  1. Comparison Table of Same-Series 3-Phase Power Supplies
หมายเลขคำสั่งซื้อ.ป้อนข้อมูล24V Outputพลังการวางตำแหน่ง
6EP1436-2BA103AC 400–500V20ก480วMedium-capacity 3-phase power supply
6EP1437-2BA103AC 400–500V40ก960วHigh-power standard 3-phase power supply
6EP1437-3BA003AC 400–500V40ก960วEquipped with relay signal output (fault contacts 13/14)
  1. นิยามเทอร์มินัล
  2. Input terminals: L1, L2, L3, วิชาพลศึกษา (3 เฟส + protective earth)
  3. Output terminals: Dual sets of +24V, 0วี (parallel for current sharing)
  4. Voltage trimming potentiometer: Located at bottom; adjust with flat screwdriver
  5. ไฟแสดงสถานะ: Solid green = normal output; ปิด / flashing = fault (การสูญเสียเฟส, ไฟฟ้าลัดวงจร, ความร้อนสูงเกินไป)
  6. สถานการณ์การใช้งานทั่วไป
  7. Large PLC control cabinets (S7-1500/400, full-station power supply for ET200SP distributed I/O)
  8. Multi-axis servo systems, inverter control stations, เวิร์กสเตชันหุ่นยนต์
  9. บรรจุภัณฑ์, การเรียงลำดับโลจิสติกส์, การเชื่อมยานยนต์ & assembly production lines
  10. การบำบัดน้ำ, พลังงานลม, โลหะวิทยา, cement and other high-power industrial control equipment
  11. Centralized 24V power supply scenarios requiring 3-phase industrial incoming power and high current loads

ปกเกล้าเจ้าอยู่หัว. การทดแทน & Capacity Expansion Solutions

  1. Upgraded same-spec model: 6EP1437-3BA00 (with fault relay contacts for PLC diagnostic connection)
  2. Capacity expansion: Parallel two 6EP1437-2BA10 units for max. 80ก / 1920W output
  3. Downsized alternative: 6EP1436-2BA10 (20ก / 480ว) for half-load applications

8. Installation Prohibitions & คู่มือการแก้ไขปัญหา

Forbidden Operations (Critical Restrictions)

  1. Horizontal or upside-down mounting is strictly prohibited; blocked cooling air duct triggers rapid over-temperature protection
  2. Long-term power-on with direct output short circuit will cause continuous hiccup power derating
  3. Long-term operation with missing input phase accelerates aging of internal power components
  4. Do not install alongside high-power inverters without partition plates to avoid EMC interference

Common Fault Matrix

ปรากฏการณ์สาเหตุที่แท้จริงมาตรการรับมือ
Green light off, no 24V output3-phase power loss, เบรกเกอร์สะดุด, internal overheatingCheck 3-phase incoming voltage; power off and cool down then restart; clean dust in air duct
Green light flashing, output voltage dropOutput overload / ไฟฟ้าลัดวงจรDisconnect loads and locate short circuit by segmentation; limit total load within 40A
Output voltage below 23V under loadUndersized cables causing excessive voltage dropThicken 24V main cables; add auxiliary power supplies nearby
Frequent over-temperature shutdownAmbient temp >55℃, clogged air duct, fully enclosed cabinetInstall cabinet cooling fan, lower ambient temperature, reserve ≥50mm top & bottom ventilation clearance

Official Overall Dimensions of ซีเมนส์ 6EP1437-2BA10 (SITOP POWER 40 3-Phase 40A Power Supply)

  1. Overall Unit Dimensions (กว้าง × สูง × ลึก, หน่วย: มม)

160 × 125 × 121 มม

ความกว้าง (horizontal along DIN rail): 160 มม

ความสูง (vertical cooling air flow direction): 125 มม

ความลึก (cabinet depth direction): 121 มม

น้ำหนักสุทธิ: ประมาณ. 2.0 กก

  1. Dimension Differentiation of Confusable Same-Series Models (Avoid Errors in Procurement & Cabinet Layout)
หมายเลขคำสั่งซื้อ.ข้อมูลจำเพาะกว้าง × สูง × ลึก (มม)น้ำหนัก
6EP1436-2BA103-phase 20A90 × 125 × 1201.6 กก
6EP1437-2BA103-phase 40A (without fault contacts)160 × 125 × 1212.0 กก
6EP1437-3BA003-phase 40A (with fault relay)160 × 125 × 1212.0 กก
6EP1437-2BA20 (New PSU300S Series)New generation 40A145 × 145 × 1503.1 กก
  1. Cabinet Installation Clearance Requirements
  2. Mounting rail: Standard 35mm TH35 DIN rail, การติดตั้งในแนวตั้ง (terminals downward)
  3. สูงสุด & bottom ventilation clearance: Reserve at least 40mm for heat dissipation; derating mandatory if ambient temp exceeds 55℃
  4. Side-by-side mounting: Units of same model can be tightly arranged without extra spacing

หมายเหตุเพิ่มเติม

Dimensions such as 250×180×92 and 145×145×150 shown on some foreign websites belong to the new PSU300S model 6EP1437-2BA20, which is incompatible with the legacy 6EP1437-2BA10. Cabinet cutout and DIN rail layout cannot be shared between them.

ก่อนหน้า:

ทิ้งคำตอบไว้

ฝากข้อความ