Fiesta 552788 Cilindro compacto ADN-20-25-I-P-A

Número de orden: 552788

Serie: Compact cylinder, ADN series, ISO 21287 obediente

Tamaño del orificio: 20 milímetros

Ataque: 25 milímetros

Amortiguación: Adjustable pneumatic cushioning at both ends

Piston rod thread: hilo interno

Piston magnet: With magnetic ring (compatible with magnetic proximity switches)

Opciones de montaje: Multiple accessories available; frente, rear, foot and flange mounting

Working medium: aire comprimido, filtered (lubricated or non-lubricated)

Presión de funcionamiento: 0.6 … 10 bar

Temperatura ambiente: -20 … +80 ℃

Tamaño del puerto: G1/8

📌 Desglose del código del modelo

adn: Compact cylinder series

20: Aburrir 20 milímetros

25: Ataque 25 milímetros

I: Internal thread on piston rod

PAG: Pneumatic cushioning

A: Integrated magnetic ring

📎 Common Compatible Accessories

Magnetic proximity switch: Serie PYME-8 (PYME-8-K-LED-24)

Mounting accessories: Foot bracket HBN, flange FBN, trunnion SNCU

Piston rod couplings: I-type coupling, Y-type coupling

🔁 Reemplazo & Substitution Information

Reemplazo de la misma serie: Use ADN with identical specification and order number. Old model ADVU is legacy compact cylinder with different construction; mounting dimensions are not directly interchangeable.

Alternativa doméstica: Select domestic compact thin cylinder, verify mounting hole pitch, aburrir, ataque, rod thread and air port position.

📋 Typical Applications

Montaje automatizado, líneas transportadoras, accesorios de herramientas, estaciones de clasificación, short-stroke pushing and clamping for 3C equipment.

Troubleshooting Guide for Fiesta ADN-20-25-I-P-A (552788)

Precaution: Cut off air supply, release pressure and lock the air supply switch before maintenance to prevent unintended movement. This model is designed for lifetime lubrication; additional oiling is not required. Dry filtered non-lubricated compressed air is recommended.

Secuencia de solución de problemas: Air supply → Solenoid valve & tubing → Flow control → Mechanical alignment → Cylinder body → Magnetic switch

Cylinder does not move at all

Suministro de aire: Low pressure (recommended 0.4~0.6 MPa), clogged filter, condensed water in FRL unit, shut-off main valve. Measure pressure at cylinder port and compare with main gauge.

circuito de control: No output from solenoid valve, burnt coil. Test valve via manual override; check for missing PLC signals.

Blocked air circuit: G1/8 port, throttle fully closed, crushed tubing. Disconnect tube and check exhaust flow.

Agarrotamiento mecánico: Jammed load, misaligned guide, binding piston rod. Disconnect load and test cylinder independently with air supply.

Cylinder internal fault: Stuck piston seal, foreign debris inside barrel. Manually push rod; obvious resistance or immobility indicates jam.

Erratic movement, judder, resbalón

Incorrect throttling: Meter-in throttling easily causes chattering. Meter-out throttling is preferred. Mount one-way flow regulators on exhaust ports and adjust gradually.

Tubing issues: Undersized tubing, long piping leading to large pressure drop. Shorten hoses or increase tube diameter.

Desalineación: Load guide not coaxial with piston rod. Use floating joint to eliminate rigid binding.

Contaminated piston rod: Dust or metal shavings scratch wiper seal. Clean rod; install protective boot for dusty environments.

Unstable supply pressure: Install upstream air reservoir for pressure stabilization.

Insufficient thrust, fails to reach end position

Low supply pressure or large transient pressure drop; add upstream air tank.

Premature hard stop from external limit: Adjust stopper. Avoid piston hard impact against external mechanical stops.

Internal leakage: Worn piston seal causing cross-port leakage. Síntoma: Rod slowly retracts under holding pressure, obvious loss of force.

Over-tight cushion screw: Cushion screw screwed too deep restricts exhaust; fine-adjust cushion screw.

Fuga de aire (externo / interno)

Fitting leakage: Uneven tube cut, incomplete insertion, poor thread sealing. Test with soapy water.

Front end external leakage: Worn wiper / rod seal, scratches on piston rod.

End cap leakage: Aged O-rings on front/rear end caps.

Internal leakage diagnosis: Pressurize one chamber; continuous exhaust from the opposite chamber confirms damaged piston seal. If cylinder barrel is scored, repair is not feasible; replace cylinder directly.

Nota: ADN compact barrels are thin-walled. Once scratched, seal replacement will quickly leak again.

Magnetic switch false triggering, no detection or signal loss (magnetic version)

Mismatched switch: SME-8 series is required for ADN magnetic rings.

Posición de montaje: Switch outside travel range or loose mounting.

Magnetic interference: Nearby iron blocks, strong magnets or metal brackets. Increase clearance.

Sobretemperatura: Operating range -20~+80℃; out-of-range temperature causes unstable switch behaviour.

Damaged magnetic ring: Cracked or demagnetised piston magnet (extraño, usually after heavy impact).

Wiring fault: Low 24V supply, broken wire or short circuit.

Heavy impact, rebound, loud end-of-stroke noise

Improper cushion setting: Excess cushion opening → impact; cushion fully closed → rebound. Adjust both cushion screws slowly for smooth stopping.

Excessive meter-out flow, alta velocidad. Reduce flow regulator setting first, then fine-tune cushion.

High load inertia exceeding built-in cushion capacity. Add external hydraulic shock absorber.

Preventive Maintenance Checklist
Air quality: Condensate, oil sludge and dust (ADN is sensitive to contaminants).
Piston rod condition: Scratches, rust and dust accumulation.
Coaxial alignment: Recheck alignment after every fixture change.
Magnetic switch mounting and wiring tightness.
Cushion setting: Vibration may loosen cushion screws over time.
Repair Decision Guidance

Only O-rings and rod seal worn, barrel undamaged: Festo original repair kit can be used for seal replacement.

Vástago de pistón rayado, scored barrel or deformation: Replace cylinder 552788 directly, repair is not recommended.

Do not add lubricating oil arbitrarily; excess oil attracts dust and accelerates seal wear.

Quick Diagnostic Tip

Disconnect load and supply air directly to cylinder:

✅ Smooth operation under no load → Fault source: Desalineación, load or external limit

❌ Still weak, juddering or leaking under no load → Fault source: Cylinder seal, barrel or cushion assembly

Festo ADN is a modular configurable cylinder. Available bores: 12/16/20/25/32/40/50/63/80/100/125 milímetros; stroke range 5 mm～500 mm. Options include A (external thread) / I (internal thread), P/PPS cushion, magnetic ring A, Q anti-rotation, S2 double rod, EL end lock, KP clamping, S1 reinforced rod, S6 high temperature, S11 low friction, R3 corrosion resistance, etc.. Tens of thousands of combinations exist; a complete master list is not available. Abajo: coding rule + frequently used base models (A-P-A / I-P-A, including your 552788) + order number table + definición de sufijo.

ADN Model Coding (Metric, ISO21287)

ADN-Bore-Stroke-Rod Thread-Cushion-Magnet-[Opciones]

adn: Double-acting compact cylinder

A: Piston rod external thread; I: Piston rod internal thread

PAG: Standard adjustable pneumatic cushion; PPP: Self-adjusting pneumatic cushion

A: Integrated magnetic ring for SME-8 switches

q: Square anti-rotation rod; T2: Double-ended piston rod; S20: Hollow double rod

EL: End position lock; KP: Clamping unit; T1: Reinforced piston rod

T6: High-temperature seal up to 120℃; S11: Baja fricción; R3: Heavy corrosion resistance; TT: Low-temperature seal (-40℃)

Standard Base Model: ADN-xx-xx-A-P-A (External Thread, Magnet, Adjustable Cushion)

Aburrir	Ataque	Modelo	Número de pedido.
12	5	ADN-12-5-A-P-A	536200
12	10	ADN-12-10-A-P-A	536204
12	15	ADN-12-15-A-P-A	536206
12	20	ADN-12-20-A-P-A	536208
12	25	ADN-12-25-A-P-A	536210
16	5	ADN-16-5-A-P-A	536220
16	10	ADN-16-10-A-P-A	536224
16	15	ADN-16-15-A-P-A	536226
16	20	ADN-16-20-A-P-A	536228
16	25	ADN-16-25-A-P-A	536230
20	5	ADN-20-5-A-P-A	536240
20	10	ADN-20-10-A-P-A	536244
20	15	ADN-20-15-A-P-A	536246
20	20	ADN-20-20-A-P-A	536248
20	25	ADN-20-25-A-P-A	536250
25	5	ADN-25-5-A-P-A	536260
25	10	ADN-25-10-A-P-A	536264
25	15	ADN-25-15-A-P-A	536266
25	20	ADN-25-20-A-P-A	536268
25	25	ADN-25-25-A-P-A	536270
32	5	ADN-32-5-A-P-A	536280
32	10	ADN-32-10-A-P-A	536284
32	15	ADN-32-15-A-P-A	536286
32	20	ADN-32-20-A-P-A	536288
32	25	ADN-32-25-A-P-A	536290
40	5	ADN-40-5-A-P-A	536300
40	10	ADN-40-10-A-P-A	536304
40	15	ADN-40-15-A-P-A	536306
40	20	ADN-40-20-A-P-A	536308
40	25	ADN-40-25-A-P-A	536310
50	10	ADN-50-10-A-P-A	536324
50	20	ADN-50-20-A-P-A	536328
50	25	ADN-50-25-A-P-A	536330
63	10	ADN-63-10-A-P-A	536344
63	20	ADN-63-20-A-P-A	536348
63	25	ADN-63-25-A-P-A	536350

Standard Base Model: ADN-xx-xx-I-P-A (Internal Thread, same style as 552788)

Aburrir	Ataque	Modelo	Número de pedido.
12	5	ADN-12-5-I-P-A	536201
12	10	ADN-12-10-I-P-A	536212
12	15	ADN-12-15-I-P-A	536213
12	20	ADN-12-20-I-P-A	536214
12	25	ADN-12-25-I-P-A	536215
16	5	ADN-16-5-I-P-A	536221
16	10	ADN-16-10-I-P-A	536232
16	15	ADN-16-15-I-P-A	536233
16	20	ADN-16-20-I-P-A	536234
16	25	ADN-16-25-I-P-A	536235
20	5	ADN-20-5-I-P-A	536241
20	10	ADN-20-10-I-P-A	536252
20	15	ADN-20-15-I-P-A	536253
20	20	ADN-20-20-I-P-A	536254
20	25	ADN-20-25-I-P-A	552788
25	5	ADN-25-5-I-P-A	536261
25	10	ADN-25-10-I-P-A	536272
25	15	ADN-25-15-I-P-A	536273
25	20	ADN-25-20-I-P-A	536274
25	25	ADN-25-25-I-P-A	536275
32	5	ADN-32-5-I-P-A	536281
32	10	ADN-32-10-I-P-A	536292
32	15	ADN-32-15-I-P-A	536293
32	20	ADN-32-20-I-P-A	536294
32	25	ADN-32-25-I-P-A	536295
40	5	ADN-40-5-I-P-A	536301
40	10	ADN-40-10-I-P-A	536312
40	15	ADN-40-15-I-P-A	536313
40	20	ADN-40-20-I-P-A	536314
40	25	ADN-40-25-I-P-A	536315
50	10	ADN-50-10-I-P-A	536332
50	20	ADN-50-20-I-P-A	536334
50	25	ADN-50-25-I-P-A	536335
63	10	ADN-63-10-I-P-A	536352
63	20	ADN-63-20-I-P-A	536354
63	25	ADN-63-25-I-P-A	536355

Common Suffix Definitions for Special Versions

q: Square anti-rotation rod (ejemplo: ADN-20-25-Q-P-A)

T2: Double-ended piston rod

S20: Hollow double rod

EL: End position locking cylinder

KP: Integrated clamping unit

PPP: Self-adjusting pneumatic cushion, replaces standard P cushion

S11: Low-friction version for low-force applications

T6: High-temperature seal, up to 120℃

R3: Heavy-duty corrosion-resistant coating for washdown/humid environments

TT: Low-temperature seal, down to -40℃

Notas adicionales
Longer stroke variants (30/40/50/80/100…500 mm), bores 80/100/125, inch variants, and special options such as Q/S2/EL/KP are numerous. This table covers frequently used short-stroke base models.
AEN is single-acting variant (not part of ADN series). ADNGF is guided compact cylinder, different product line.
Legacy compact cylinder ADVU has different mounting geometry and cannot be swapped directly.