Schneider ATV650D30N4 Variable Speed Drive

(Altivar Process ATV650)

Model code explanation: ATV650 = Altivar Process IP55 wall-mounted ドライブ; D30 = 30 kW normal duty rating; N4 = 3-phase 380~480V, without integrated input disconnect switch (version with switch carries suffix E: ATV650D30N4E)

✅ Core Electrical Specifications
定格電力: 30 kW normal duty / 22 kW heavy duty (40HP / 25HP)
供給: 3-phase 380…480V, 50/60 Hz
Output current, 通常の勤務: 61.5 あ; heavy duty current: 39.2 あ (4 kHz carrier frequency)
フレームサイズ: フレームB (Frame B covers 30~45 kW range)
Enclosure rating: IP55, wall-mounted design for local field installation, no additional control cabinet required
冷却: 強制空冷
Compatible motors: Asynchronous motors, synchronous reluctance motors
EMCフィルター内蔵: クラスC2 (motor cable ≤50 m), Class C3 (motor cable ≤150 m)

✅ Interfaces & コミュニケーション
Integrated Dual-port Ethernet (Modbus TCP) + RS485 Modbus
デジタル I/O: 8 から, 3 configurable relay outputs
アナログI/O: AI / へ; on-board process PID, flow estimation, energy metering dashboard
拡大: Supports Profibus-DP, プロフィネット, EtherNet/IP communication option cards
標準付属品: Chinese graphic keypad, QR code for maintenance access, equipment asset monitoring, drift alarm, 停止&Go energy-saving function

✅ Typical Applications
Water supply pumps, wastewater pumps, 空調ファン, 冷却塔, chemical fluid handling, air compressors and other process fluid loads. Focused on energy saving, asset management and predictive maintenance; 埃っぽいものに適した, humid field environments (IP55)

✅ Cross-series Comparison & 交換品
1. ATV650D30N4E: Same power rating, with integrated load disconnect switch
2. ATV630D30N4: Same power rating, IP20 cabinet-mounted bare drive (no outer enclosure)
3. アップグレード交換: ATV660D30N4; for heavy-duty impact loads, select ATV950

✅ Important Notes
IP55 units have stricter heat dissipation requirements; reserve vertical ventilation clearance above and below when wall mounting
Dual rating mode (通常業務 / ヘビーデューティ) can be switched in parameter group 5.2
Commissioning software: ソームーブ, firmware version V4.6IE47

ATV650 (Altivar Process ATV600 Series) Fault Code List
1. 供給 & Input Side Faults
1. IPF / IPL Input phase loss / 3-phase unbalance
原因: 入力位相が欠落しています, ヒューズが切れた, severe 3-phase voltage unbalance, 3-phase detection enabled incorrectly for single-phase supply
救済策: Check incoming circuit breaker / ヒューズ; set IPL to nO to disable phase loss detection if running on single-phase supply

2. OVF DC bus overvoltage
原因: Mains voltage too high, deceleration time too short, regenerative energy from high-inertia loads
救済策: 減速時間を長くする; fit braking resistor; activate adaptive deceleration brA

3. ObF Overvoltage stall (trip due to excessive DC bus voltage)
原因: 急減速, high load inertia, excessive regenerative energy
救済策: 減速時間を延長する; enable stall prevention; ブレーキユニットを取り付ける + resistor

4. UVF DC bus undervoltage
原因: Mains dip, momentary power loss, loose incoming connections, contactor chatter
救済策: 電源を確認してください; extend undervoltage delay; improve wiring connections

5. PHF Supply phase sequence error
救済策: Swap any two incoming phases L1/L2/L3

2. 出力 & Motor Side Faults
1. OCF Output overcurrent
原因: Motor locked rotor, shorted output cable, motor insulation breakdown, rapid acceleration/deceleration
救済策: Disconnect motor and run no-load test; reduce acceleration/deceleration ramps; test cable insulation to earth with megger

2. SCF Output short-circuit / 地絡
原因: Damaged motor cable shorted to earth, motor winding earth fault, failed drive IGBT
救済策: Disconnect motor and test drive output separately; measure motor winding insulation to earth

3. OPF2 / OPF Output phase loss (モーター欠相)
原因: Loose motor terminals, open output contactor, small motor running at light load
救済策: Tighten motor wiring; disable OPL phase loss detection if an output contactor is used; disable phase loss protection for small motors

4. OLF Motor thermal overload
原因: Continuous overloading, ロックされたローター, motor thermal current ITH parameter set too low
救済策: 負荷を軽減する; adjust motor thermal current ITH; wait for motor to cool before reset

5. OLC Drive hardware current limit overload
救済策: 負荷を軽減する; check output for short circuits; lower carrier frequency

6. OTF1 / OTF2 Motor PTC thermistor overheat
原因: Motor winding overtemperature, broken or shorted PTC probe
救済策: Check motor temperature; measure PTC resistance; disable this protection if no temperature probe is fitted

3. Drive Overheating Faults
1. OHF Drive heatsink overtemperature (common fault)
原因: Failed cooling fan, clogged filter, insufficient mounting clearance, 周囲温度が高い, heavy dust accumulation
救済策: Clean air filter; check cooling fan; set fan permanent ON mode; maintain vertical ventilation clearance; monitor heatsink temperature parameter THD

2. OHFd DC reactor overtemperature
救済策: 負荷を軽減する; improve enclosure ventilation

4. Braking Circuit Faults
1. bUF Braking circuit fault
原因: Open braking resistor, failed braking IGBT, 配線が緩んでいる
救済策: Check braking resistor resistance and connections; test braking unit at no load

2. bOF Braking resistor overload
救済策: Select higher resistance braking resistor; 減速時間を延長する

5. Safety Circuit Faults (STO 安全トルクオフ)
1. SAFF STO safety circuit fault
原因: Mismatched timing between STOA and STOB (time difference >1 s), broken wiring, internal hardware fault
救済策: Check both STO wiring paths; ensure STOA and STOB switch simultaneously; both paths must be shorted together for bypass

2. SdF Safety function active (normal stop, not a hardware fault)
状態: STO terminals open, drive locked; reset only after restoring STO wiring

6. コミュニケーション & Analog Signal Faults
1. CnF1~CnF4 Communication link fault (Modbus TCP / RS485)
原因: Damaged Ethernet cable, incorrect termination resistor, IPアドレスの競合, electrical noise interference
救済策: Inspect cables; use shielded communication cable; verify IP settings; reduce baud rate

2. AIF Analog input wire break (4–20 mA current signal)
原因: Broken sensor cable, 開回路, signal below 4 ミリアンペア
救済策: Check transmitter and signal wiring; lower wire-break threshold if required

3. AOF Analog output fault

7. Internal Hardware Faults (InF series, generally hardware damage)
1. InF8 Internal power supply fault (power board supply abnormal)
救済策: Full power cycle; repeated fault = replace power board

2. InFL (InF21) Real-time clock fault, keypad communication failure
救済策: Remove keypad, remove battery and re-power; replace keypad; if fault persists, 制御基板を交換する

3. InF1~InF7, InF9~InF30 Other internal hardware errors
救済策: 電源を入れ直します; fault cannot be cleared → control board / power board damaged, requires repair or replacement

8. Process-specific Faults (ポンプ / fluid functions exclusive to ATV650)
1. iPPF Low inlet pressure protection (dry-run / low suction protection)
原因: Insufficient inlet pressure, faulty pressure transmitter, protection threshold set too high
救済策: Check pipeline suction pressure; calibrate pressure transducer; reduce low-pressure threshold

2. HPF High pressure protection, LPF Low pressure protection, FLF Flow fault

3. DryF Dry-run protection (pump running without fluid)
救済策: Verify pump suction availability; adjust dry-run current threshold

9. Other General Faults
1. FrF Frequency feedback fault (encoder wire break)
2. USF Motor autotune failed on power-up
3. CLF Cooling circuit fault (water-cooled versions only)
4. tJF Motor stall protection

10. Fault Reset Methods
1. Auto-reset: Enable automatic retry via parameter Atr
2. 手動リセット: Assign DI terminal function rSF for remote reset; reset via keypad
3. Internal hardware faults (InF codes): Require full power cycle; some faults need board replacement

Model Prefix Rules
ATV650: Altivar Process IP55 wall-mounted variable speed drive (3-相380~480V)
U: Low power range (0.75~7.5 kW); D: Medium power range (11~90 kW); C: High power floor-standing unit (110 kW以上, IP54)
N4: Without integrated disconnect switch; N4E: With integrated load disconnect switch
Enclosure rating: All wall-mounted units = IP55; floor-standing C models = IP54

Wall-mounted IP55 Full Model List (N4 without switch / N4E with switch, main domestic variants)
Frame A (0.75～22 kW)

フレームB (30～45 kW, includes your D30N4)

Frame C (55～90 kW)

High Power Floor-standing Units (C range, IP54, 垂直設置)
Model format: ATV650CxxN4F (all fitted with disconnect switch)
110/132/160/200/250/315 kW:
ATV650C11N4F, C13N4F, C16N4F, C20N4F, C25N4F, C31N4F

Confusable Series Comparison
1. ATV650: IP55 wall-mounted, for local field installation (the series you are using)
2. ATV630: Same power rating, IP20 cabinet bare drive, no outer enclosure
3. ATV660: Newer generation, upgrade replacement for ATV650
4. ATV950: 耐久性の高いドライブ, for shock loads other than fans and pumps

Additional Key Information
Suffix U = low power; D = medium power; C = high power floor-standing
Suffix E = integrated load disconnect switch; no E = no switch
Standard features for all units: Dual-port Modbus TCP + RS485, built-in Class C2/C3 EMC filter, Chinese graphic keypad, STO 安全トルクオフ