コンタクタ,サーキットブレーカー,ソーラーインバーター,電気メーター,太陽電池
This is a 3-way/2-way solenoid proportional modulating valve with DN20 (3/4″) スレッド接続と Kvs 値 5.0 m3/h. 24V AC/DC電源で動作します, 選択可能な制御信号付き: 0-10V / 2-10V / 4-20ミリアンペア. It features a positioning time of less than 2 秒, a resolution of 1:1000 and an IP54 protection rating. It is designed for mixing and straight flow control of cold and hot water in closed HVAC systems.
- 型式コードの説明
| コードセグメント | 説明 |
| MXG | 製品シリーズコード: MX stands for solenoid actuator; G stands for external thread connection, suitable for cold and hot water systems |
| 461 | Model type code: ACVATIX™ series solenoid control valve, PN16 pressure rating |
| 0.2 | Nominal diameter DN: 20mm (3/4 インチ) |
| -5 | Kvs flow coefficient: 5.0 m3/h (flow rate of cold water at 1 bar pressure differential) |
| (Suffix P) | Optional version: For media containing mineral oil (SAE05…SAE50) |
| (サフィックス U) | Optional version: Equipped with NPT thread fitting set |
- 主な技術仕様
| カテゴリ | 仕様 | 備考 |
| 基本パラメータ | ||
| バルブの種類 | Switchable 3-way mixing valve / 2-way straight valve | Not applicable for diverting service |
| 接続タイプ | External thread G1¼B (ISO 228-1) | DN20 corresponds to 3/4 インチ |
| Nominal Pressure | PN16 (1.6MPa) | マックス. working pressure: 1000kPa |
| 流量係数 | Kvs=5.0 m³/h, Cv=5.9 | Cold water at 5-30℃, 1 bar pressure differential |
| Actuator Parameters | ||
| 電源 | AC/DC 24V ±20% (SELV/PELV) | 頻度: 45-65Hz |
| 制御信号 | DC 0/2-10V or DC 4-20mA (DIP switch selectable) | 入力インピーダンス: ≥100kΩ (voltage signal), 100おお (current signal) |
| Position Feedback | DC 0-10V (Load resistance >500おお) | Non-wear inductive measurement |
| Positioning Time | < 2 秒 | 素早い応答 |
| Stroke Resolution | 0.736111111 | 高い調整精度 |
| 保護クラス | IP54 | Dustproof and splash-proof |
| Valve Body Parameters | ||
| バルブボディ材質 | Cast iron EN-GJL-250 (GG25) | プラグ: CrNi steel; シート: 真鍮 |
| シール材質 | EPDM (標準) / FPM (タイプP) | For different media |
| 中温 | 1-130℃ | For cold and hot water systems |
| Leakage Rate | A→AB: ≤0.02% Kvs; B→AB: ≤0.2% Kvs | At Δp=0.1MPa |
| 取付位置 | Vertical to horizontal installation available | No special angle restrictions |
| Fail-Safe Function | Port A→AB closes automatically upon power loss (スプリングリターン) | Safety protection feature |
| 物理パラメータ | ||
| 寸法 (L1×L2×L3×H2) | 95×47.5×52.5×260mm | Under straight flow status |
| 重さ | 4.2kg |
- 全シリーズモデルリスト
| モデル | DN | クヴス (m3/h) | 接続タイプ | 適用媒体 | 備考 |
| MXG461.15-0.6 | 15 | 0.6 | External thread | 寒い & お湯 | スタンダードモデル |
| MXG461.15-1.5 | 15 | 1.5 | External thread | 寒い & お湯 | スタンダードモデル |
| MXG461.15-3.0 | 15 | 3 | External thread | 寒い & お湯 | スタンダードモデル |
| MXG461.20-5.0 | 20 | 5 | External thread | 寒い & お湯 | 現行モデル |
| MXG461.25-8.0 | 25 | 8 | External thread | 寒い & お湯 | スタンダードモデル |
| MXG461.32-12 | 32 | 12 | External thread | 寒い & お湯 | スタンダードモデル |
| MXG461.40-20 | 40 | 20 | External thread | 寒い & お湯 | スタンダードモデル |
| MXG461.50-30 | 50 | 30 | External thread | 寒い & お湯 | スタンダードモデル |
| MXG461.XX-XXP | 15-50 | 0.6-30 | External thread | Mineral oil | Version for oil media |
| MXG461.XX-XXU | 15-50 | 0.6-30 | External thread | 寒い & お湯 | Version with NPT fittings |
| MXF461.XX-XX | 15-65 | 0.6-50 | フランジ | 寒い & お湯 | Flanged version |
- クロスブランド & Replacement Model Reference
| カテゴリ | モデル | Matching Rate | 違い |
| シーメンスの同等モデル | MXG461.20-5.0P | 100% | Only seal material changed to FPM, suitable for mineral oil |
| MXG461.20-5.0U | 100% | Supplied with NPT thread fittings for easier installation | |
| MXF461.20-5.0 | 95% | Flanged connection type, different mounting method | |
| 国内代替品 | Muyi MVC20-5.0 | 90% | Identical functions, 約. 60% of Siemens price, response time 2-3s |
| Chuanyi ZDLP-20K | 85% | Electric actuator, slightly lower accuracy, IP65 rating | |
| Imported Competitors | Honeywell V5011P2010 | 90% | Similar structure and price, positioning time around 2s |
| Danfoss AVTA20-50 | 85% | Slightly different flow characteristics, operating temperature 2-120℃ |
- アプリケーション環境 & 業界の事例
5.1 該当するシナリオ
HVAC システム: Cold/hot water mixing control and fan coil unit temperature regulation for commercial buildings, ホテルと病院
地域暖房: Secondary hot water temperature control for residential communities and office parks
Industrial Temperature Control: Water flow regulation for chillers and heat pumps, cooling systems for data centers
プロセス冷却: Temperature control loops for plastic molding machines and printing equipment
5.2 推奨されないシナリオ
Media with solid particles (A pre-filter with filtration accuracy ≥100μm is required)
Vacuum systems or working conditions with high pressure differential (>300kPa)
Diverting flow applications (For mixing and straight flow only)
Corrosive media (Select MXG461S stainless steel version)
5.3 代表的な応用例
場合 1: HVAC System of Commercial Complex
Project: HVAC water system renovation for a 30-floor shopping mall
応用: Cold and hot water mixing control for air handling units on each floor, 合計 80 sets of MXG461.20-5.0
結果: Temperature control accuracy improved to ±0.5℃, エネルギー消費量の削減 18%, response speed tripled
場合 2: Industrial Water Chiller
装置: 500RT screw chiller
応用: Chilled water outlet temperature control (7℃), 4 units operated in parallel
特徴: Matched with Siemens PLC for 0-10V proportional control, water temperature fluctuation stabilized below 0.3℃
- トラブルシューティング & メンテナンスガイド
| 故障現象 | 考えられる原因 | トラブルシューティングの手順 | ソリューション |
| バルブが作動しない | 1. No power supply | 1. 端子電圧を測定する (24V±20%) | 1. 電源回路の修理 |
| 2. Missing control signal | 2. Check 0-10V/4-20mA control signal | 2. Inspect controller output | |
| 3. Actuator failure | 3. Manual operation test (Turn handwheel clockwise) | 3. Replace ASE1 electronic module | |
| Poor regulating accuracy | 1. Position offset | 1. Perform auto-calibration (Long press calibration button) | 1. Recalibrate the valve |
| 2. Incorrect valve characteristic setting | 2. Check DIP switch (リニア / 等しいパーセンテージ) | 2. Reset DIP switch | |
| 3. Impurities in medium | 3. Inspect filter cleanliness | 3. Clean the filter | |
| Excessive leakage | 1. Aged seals | 1. Check seal condition | 1. Replace EPDM seals |
| 2. Worn valve seat | 2. Measure leakage under closed status | 2. Replace valve seat assembly | |
| 3. Excessive pressure differential | 3. Confirm system pressure differential ≤300kPa | 3. Install bypass valve to reduce pressure difference | |
| 異常なフィードバック信号 | 1. Faulty feedback wiring | 1. Measure feedback terminal voltage (0-10V) | 1. Repair feedback wiring |
| 2. Damaged electronic module | 2. Check module indicator lights | 2. Replace electronic module | |
| 3. Defective inductive sensor | 3. Inspect sensor connection | 3. Replace inductive sensor |
メンテナンススケジュール
| メンテナンス品 | サイクル | Operation Content |
| 目視検査 | 毎月 | Check valve body and actuator for damage and loose connections |
| フィルターの掃除 | 四半期ごと | Clean inlet filter to prevent impurity ingress |
| Auto-Calibration | 半年ごと | Execute auto-calibration to ensure positioning accuracy |
| Seal Inspection | 毎年 | Check seal aging and replace if necessary |
| オーバーホール | 毎 3 年 | Dismantle for internal inspection and replace wearing parts |
- 選定ガイドライン
- 3 つの主要な選択要素: DN size (match pipeline) → Kvs flow rate (meet system demand) → Medium type (Standard type for cold/hot water, Type P for mineral oil)
- Signal Selection: DC 0-10V for general control; DC 4-20mA for long-distance transmission (強力な干渉防止)
- Installation Tips: Follow the flow direction marked on the valve body; do not use as diverting valve; 4-wire connection for power and signal ensures higher stability
- Fault Judgment: Automatic shutdown after power loss (スプリングリターン) is a standard safety function; manual operation can quickly verify mechanical performance
- 注文情報
スタンダードモデル: MXG461.20-5.0 (BPZ:MXG461.20-5.0)
推奨アクセサリ: ALG203 thread fitting set (3 union nuts + 3 ガスケット + 3 平座金), Z155/20 blind flange set
Replacement Module: ASE1 electronic module (Applicable for DN15-32)
Supplementary Application Description
MXG461.20-5.0 is a DN20 solenoid proportional modulating valve with Kvs=5.0. It is mainly used for continuous and precise temperature control in closed cold and hot water systems. Featuring fast positioning (<2s) and high resolution (1:1000), it is only applicable for mixing and straight flow, not for diverting service.
- 空調設備 & 冷凍 (Primary Application)
Air Handling Units / Fresh Air Units: Proportional regulation of cold/hot water coils to stabilize supply air temperature (±0.5℃)
Fan Coil Units (FCU): Terminal temperature control for high-rise and commercial buildings, available for 2-way on/off or 3-way mixing flow
Chilled Water Systems: Water temperature regulation and bypass mixing control for chillers
Cooling Tower Control: Stabilize cooling water temperature and save energy
Computer Room Precision Air Conditioning: High-precision water temperature control for data center and equipment room cooling
- 地域暖房 & Boiler Systems
Heat Exchanger Stations: Secondary hot water temperature regulation and mixing loop control
Radiant Floor Heating: Limit supply water temperature (35–45℃) and prevent overheating via 3-way mixing
Boiler Load Control: Stabilize hot water outlet temperature and follow system load changes
Domestic Hot Water (DHW): Mix cold and hot water to provide constant-temperature water (例えば. 45–55℃)
- Industrial Process & Special Media
プロセス冷却: Precise cooling water temperature control for injection molding machines, printing machines and lasers
Mold Temperature Controllers: Proportional regulation for thermal oil and hot water circuits (Type P for mineral oil)
食べ物 & 製薬産業 (Sanitary Application): Closed-loop temperature control for pure water and hot water
Solar Water Heating Systems: Mix water from solar collectors and return water for constant water supply
- Typical Circuit Applications
3-way Mixing (Combining Flow): Mix high-temperature primary water and low-temperature secondary water to stabilize supply water temperature (most common application)
2-way Straight Flow: On/off or proportional regulation for coil/equipment inlet, automatic shutdown upon power loss for safety
Bypass / Differential Pressure Control: Stabilize system pressure difference and balance flow under partial load
- Disqualified Application Scenarios
❌ Media with solid particles (Pre-filter ≥100μm required)
❌ Diverting flow service (Mixing and straight flow only)
❌ Vacuum conditions, high pressure differential (>300kPa) or highly corrosive media
❌ Steam systems (Operating medium: cold/hot water and thermal oil, 1–130℃)
- Application Matching Based on Core Advantages
素早い応答 (<2s): Ideal for systems with fluctuating load requiring rapid temperature stabilization, such as HVAC terminals and process cooling
High Resolution (1:1000): Suitable for high-precision temperature control scenarios including precision air conditioning, pharmaceutical and electronic manufacturing
電源オフの安全性 (Port A→AB Closed): Safety loop for heating and hot water systems to avoid overheating and scalding risks
