コンタクタ,サーキットブレーカー,ソーラーインバーター,電気メーター,太陽電池
Siemens 6EP1437-2BA10 SITOP POWER 40 三相 産業用電源
- モデルコードの内訳
6EP1437-2BA10
6EP: Standard industrial power supply series of SITOP
1437: High-power three-phase AC model, 40A output platform
2: Basic standard version (without redundant diagnostic interface)
BA: DINレール取付, 24VDC出力
10: 3-phase 400–500V input, 40あ / 960W output specification
- コアの電気パラメータ
Input Side (3-Phase Industrial Grid)
Input format: 3×400～500V AC, 3-phase 5-wire L1/L2/L3/PE
頻度: 50/60Hz
Voltage dip tolerance: Minimum 340V for 2 seconds without output collapse
Wire gauge for input terminals: 0.5～4mm² solid/stranded copper wire
Output Side (Standard Industrial 24VDC)
Rated output: 24VDC / 40あ, total power 960W
Adjustable output voltage range: 22.8～26.4V (tweaked via potentiometer at bottom)
リップル & ノイズ: Ripple ＜150mVpp, peak noise ＜240mVpp
Output terminals: Dual groups of +/terminals for parallel connection; wire gauge 0.5～10mm²
Parallel expansion: Two identical units can be directly paralleled for max. 80A output
保護機能 (Full-condition Protection)
- 短絡保護: Automatic hiccup current limiting, auto-recovery after fault clearance
- 過電圧保護 (OVP): Output cut-off when voltage ＞27V
- 過負荷保護 (OLP): Current limiting at 120% 定格電流
- Over-temperature Protection (OTP): Shutdown on overheat, auto-restart after cooling down
- Protection against input phase loss, surge and industrial EMC interference
Ⅲ. 機械式 & 環境仕様
取り付け: Vertical installation on standard 35mm DIN rail
全体の寸法 (幅×高さ×奥行き): 160 × 125 × 121 mm
Net weight: 約. 2.0 kg
保護クラス: IP20 (キャビネット設置のみ)
動作温度: 0～+55°C (full power derating required above 55°C)
ストレージ / 輸送温度: -25℃～+85℃
湿度: 5%～95%RH, 結露なし
認証: CE, UL, GL marine certification; compliant with EN61010, EN61000 industrial EMC standards
- Comparison Table of Same-Series 3-Phase Power Supplies
| 注文番号. | 入力 | 24V Output | 力 | 位置決め |
| 6EP1436-2BA10 | 3AC 400–500V | 20あ | 480W | Medium-capacity 3-phase power supply |
| 6EP1437-2BA10 | 3AC 400–500V | 40あ | 960W | High-power standard 3-phase power supply |
| 6EP1437-3BA00 | 3AC 400–500V | 40あ | 960W | Equipped with relay signal output (fault contacts 13/14) |
- 端子の定義
- Input terminals: L1, L2, L3, PE (3 フェーズ + protective earth)
- Output terminals: Dual sets of +24V, 0V (parallel for current sharing)
- Voltage trimming potentiometer: Located at bottom; adjust with flat screwdriver
- 表示灯: Solid green = normal output; オフ / flashing = fault (位相損失, 短絡, 過熱)
- 典型的なアプリケーションシナリオ
- Large PLC control cabinets (S7-1500/400, full-station power supply for ET200SP distributed I/O)
- Multi-axis servo systems, inverter control stations, ロボットワークステーション
- 包装, 物流仕分け, automotive welding & assembly production lines
- 水処理, 風力, 冶金, cement and other high-power industrial control equipment
- Centralized 24V power supply scenarios requiring 3-phase industrial incoming power and high current loads
Ⅶ. 交換 & Capacity Expansion Solutions
- Upgraded same-spec model: 6EP1437-3BA00 (with fault relay contacts for PLC diagnostic connection)
- Capacity expansion: Parallel two 6EP1437-2BA10 units for max. 80あ / 1920W output
- Downsized alternative: 6EP1436-2BA10 (20あ / 480W) for half-load applications
VIII. 設置禁止事項 & トラブルシューティングガイド
Forbidden Operations (Critical Restrictions)
- Horizontal or upside-down mounting is strictly prohibited; blocked cooling air duct triggers rapid over-temperature protection
- Long-term power-on with direct output short circuit will cause continuous hiccup power derating
- Long-term operation with missing input phase accelerates aging of internal power components
- Do not install alongside high-power inverters without partition plates to avoid EMC interference
Common Fault Matrix
| 現象 | 根本的な原因 | 対策 |
| Green light off, no 24V output | 3-phase power loss, サーキットブレーカーが落ちた, internal overheating | Check 3-phase incoming voltage; power off and cool down then restart; clean dust in air duct |
| Green light flashing, output voltage drop | Output overload / 短絡 | Disconnect loads and locate short circuit by segmentation; limit total load within 40A |
| Output voltage below 23V under load | Undersized cables causing excessive voltage drop | Thicken 24V main cables; add auxiliary power supplies nearby |
| Frequent over-temperature shutdown | Ambient temp ＞55℃, clogged air duct, fully enclosed cabinet | Install cabinet cooling fan, lower ambient temperature, reserve ≥50mm top & bottom ventilation clearance |
Official Overall Dimensions of シーメンス 6EP1437-2BA10 (SITOP POWER 40 3-Phase 40A Power Supply)
- Overall Unit Dimensions (幅×高さ×奥行き, ユニット: mm)
160 × 125 × 121 mm
幅 (horizontal along DIN rail): 160 mm
身長 (vertical cooling air flow direction): 125 mm
深さ (cabinet depth direction): 121 mm
Net weight: 約. 2.0 kg
- Dimension Differentiation of Confusable Same-Series Models (Avoid Errors in Procurement & Cabinet Layout)
| 注文番号. | 仕様 | 幅×高さ×奥行き (mm) | 重さ |
| 6EP1436-2BA10 | 3-phase 20A | 90 × 125 × 120 | 1.6 kg |
| 6EP1437-2BA10 | 3-phase 40A (without fault contacts) | 160 × 125 × 121 | 2.0 kg |
| 6EP1437-3BA00 | 3-phase 40A (with fault relay) | 160 × 125 × 121 | 2.0 kg |
| 6EP1437-2BA20 (New PSU300S Series) | New generation 40A | 145 × 145 × 150 | 3.1 kg |
- Cabinet Installation Clearance Requirements
- 取付レール: Standard 35mm TH35 DIN rail, 垂直設置 (terminals downward)
- トップ & bottom ventilation clearance: Reserve at least 40mm for heat dissipation; derating mandatory if ambient temp exceeds 55℃
- Side-by-side mounting: Units of same model can be tightly arranged without extra spacing
補足
Dimensions such as 250×180×92 and 145×145×150 shown on some foreign websites belong to the new PSU300S model 6EP1437-2BA20, which is incompatible with the legacy 6EP1437-2BA10. Cabinet cutout and DIN rail layout cannot be shared between them.
