Bently Nevada 3500/92-A04-B01-C00 Communication Gateway Module

상표: Bently Nevada (Baker Hughes), part of the 3500 Series TSI Machinery Protection System, full-height rack card, base part number: 138629-01; Official Name: Communication Gateway (commonly referred to as communication module in the industry). It collects all monitoring data within the 3500 rack and transmits it externally to DCS/PLC or host computer.

1. 모델 코드 설명: 3500/92-A04-B01-C00

3500: 3500 Machinery Protection TSI System

/92: Communication Gateway Module (replaces legacy 3500/90; compared with 3500/91M, it supports custom Modbus register configuration)

A04: Segment A = Serial Submodule Option, 04 = RS485 Modbus RTU Interface

B01: Segment B = Certification Option, 01 = With CSA NRTL/C Safety Certification

C00: Segment C = Additional Option, 00 = No extra options

Key Distinctions

3500/91중: EGD protocol gateway, focused on Ethernet broadcast

3500/92: Supports custom Modbus register mapping, the most widely used TSI external communication card for projects

3500/92-A04: RS485 serial port only; A01 = RS232; A02 = RS422

1. 핵심 기술 사양

III. 핵심 기능

1. Rack data aggregation and forwarding: Collect real-time values, alarm status and module fault information of all monitoring cards (진동, displacement, 온도, 등.) in the rack and output externally.
2. Dual communication interfaces: RJ45 Ethernet + RS485 serial port can work simultaneously. Ethernet is used for PC configuration / System1; RS485 Modbus RTU connects to DCS.
3. Flexible Modbus register configuration: Custom register allocation, select measurement points, set range scaling to adapt to DCS address planning, support uploading alarm bits, channel status and rack trip signals.
4. 이벤트 & timestamp upload: Alarm trigger and card fault come with timestamps for unit event recording on host computer.
5. Module self-diagnosis: Backplane communication fault, Ethernet/serial link fault, card self-check abnormality. OK indicator triggers alarm and writes information into rack event log.
6. 일반적인 애플리케이션 시나리오

Bently Nevada 3500/33-A01-B00 16-Channel Relay Module

TSI protection systems for steam turbines, 압축기, fans and large pumps; applied in petrochemical, thermal power and coal chemical industries.

목적: Serve as the data interface between TSI system and DCS, transmit shaft vibration, axial displacement, differential expansion, rotating speed, temperature and other process & protection measurement points to DCS graphics and history database.

메모: 3500/92 only transmits data and does NOT participate in protection trip logic. Hardwired trip contacts rely on 3500/33 relay card.

1. 설치 & Configuration Guidelines
2. Rack Slot: Right-hand slot of RIM. Single or multiple 92 gateways can be configured in one rack. Communicate via backplane; verify rack version compatibility before installation.
3. 배선사양

이더넷: Shielded twisted pair cable, industrial switch, isolated independent network. Do not mix with DCS control network.

RS485 Modbus: Shielded twisted pair cable, match terminal resistor at bus end, single-point grounding to reduce interference.

3. Configuration Procedure

Connect rack via Rack Configuration software;

Enter 3500/92 기준 치수, enable Modbus, configure serial parameters (주소, 전송 속도, 둥가);

Open Modbus register mapping tool, select measurement points, set range scaling and generate custom register table;

Download configuration to rack; test register reading with Modbus simulator, verify values and alarm bits.

4. 시운전: Confirm OK indicator steady on, TX/RX lights blink for backplane communication; then test Modbus polling on DCS side.
5. Common Troubleshooting Checklist
6. OK indicator off / flashing: Hardware fault of card, abnormal rack backplane communication. Re-seat the card and inspect RIM module.
7. Ethernet connection failure: 손상된 케이블, mismatched IP subnet, firewall interception. Check PC IP and 3500/92 port IP.
8. DCS cannot read RS485 Modbus data: Mismatched Modbus slave address, 전송 속도, parity check; terminal resistor not enabled; multi-point grounding of bus; register map not downloaded.
9. Value deviation: Incorrect range scaling parameters during configuration.
10. No data for partial measurement points: Corresponding channel measurement points are not added to register mapping table.

Ⅶ. 시리즈 비교 & 모델 선택