Bussmann 200FEE 고속 반도체 퓨즈 - 접촉기,회로 차단기,감지기,인코더,PLC,변환기

위챗: +86-13184948252 왓츠앱: 0086-13811255435 이메일: kent@bestcontactor.com

에 대한 연락하다 |

Bussmann 200FEE 고속 반도체 퓨즈 - 접촉기,회로 차단기,감지기,인코더,PLC,변환기

전기 같은/

Bussmann 200FEE 고속 반도체 퓨즈

기본정보모델: 200FEE Brand: Eaton Bussmann Type: BS88 Part4 / IEC60269-4 high-speed bolted dual-barrel fuse, AR 수업 (for semiconductor protection only) 정격전류: 200A Electrical Specifications IEC Rating: 690뷔와 / 500V DC UL Rating: 700뷔와 / 500V DC Breaking Capacity: 200그만큼 (AC rms); 50kA @500V DC Pre-arcing I²t: 1900; 총 청산 I²t: ...

  • 제품 세부정보

기본정보

모델: 200FEE

상표: 이튼 부스만

유형: BS88 Part4 / IEC60269-4 high-speed bolted dual-barrel 퓨즈, AR 수업 (for semiconductor protection only)

정격전류: 200에이

전기 사양

IEC Rating: 690뷔와 / 500DC에서

UL Rating: 700뷔와 / 500DC에서

차단 용량: 200그만큼 (AC rms); 50kA @500V DC

사전 아크 I²t: 1900; 총 청산 I²t: 7100@415V, 11400@660V

전력 소비: 52여

No built-in fuse indicator; external kits TI700, MAI / MBI microswitch assemblies are available

장착 치수

장착 볼트: M8

Terminal Centre Spacing: 71mm

건설: Offset dual-barrel, bolt-connected blade terminals (blade end × blade end)

Overall Size: 187폭이 mm, 100mm 길이, 22mm high, 순중량: 89.6g

승인 & 표준

CE, RoHS 규제, UL 인정

표준: BS88 Part4, IEC 60269-4

일반적인 응용 분야

Short-circuit protection for frequency converters, 정류기, DC busbars, DC 드라이브, thyristors and IGBT power semiconductors

동일한 시리즈의 참조 모델 (FEE Series)

100FEE, 125FEE, 160FEE, 200FEE, 250FEE, 315FEE, 등. Same design logic, only rated current differs

교체 노트

This is a BS88-4 aR high-speed semiconductor fuse. For domestic alternatives, 확인하다: aR classification, I²t value, 차단 용량, M8 mounting and 71mm centre spacing. Ordinary gG/gL distribution fuses cannot be used as substitutes.

The 200FEE (FEE series BS88 Part4 aR high-speed dual-barrel fuse) has no original standard moulded fuse holder.

It is designed as M8 bolt-on blade terminals (blade end). The standard installation method is direct mounting onto busbars. Holders such as RS200H (Red Spot) are not required (RS200H is for BS88-2 gG distribution fuses and is incompatible with FEE high-speed semiconductor fuses).

옵션 액세서리 (Not Holders – Indicator / Microswitch Kits)

TI700: Fuse indicator kit (indicator flag + 클립)

MAI: Microswitch adapter (fuse blown alarm signal)

MBI: Microswitch adapter (alternative construction)

Two Engineering Solutions

  1. Standard Solution (Most common for VFD / DC busbars)

Direct busbar mounting with M8 bolts, 71mm terminal centre spacing. TI700 / MAI / MBI may be fitted for blown-fuse signalling as required.

  1. IP20 Enclosed Holder (대체 솔루션)

No original Bussmann holder is available. Only third-party bolt-on high-speed fuse holders can be selected. Mandatory selection criteria:

Compatible with M8 terminals, 71mm centre spacing, rated ≥200A, 690다섯, AR 수업, breaking capacity ≥200kA

All FEE series models (100FEE /125FEE /160FEE /200FEE /250FEE /315FEE) adopt the same busbar bolt-on design; no original holders are supplied.

200FEE (FEE Series BS88 Part4) 설치 토크 & Tightening Specification

메모: The manufacturer datasheet does not specify torque for this individual model. The values below are industry standard practice for Eaton BS88 fuses and busbar connections, widely used for VFD and DC bus projects.

볼트 크기: M8 (coarse pitch 1.25), 8.8 grade galvanized bolts preferred

✅ Recommended Torque: 10 N·m (±1 N·m)

Acceptable Range: 9 N·m (분) ~ 12 N·m (최대)

Do not exceed 12 N·m: risk of deforming fuse copper terminals and uneven contact surfaces. Torque below 9 N·m causes high contact resistance, overheating and nuisance blowing.

  1. Washer Stack Order (from busbar outwards)

Busbar → Fuse blade terminal → Plain washer → Spring washer → Nut

금지: Spring washer between fuse terminal and copper busbar; stacking multiple lugs on one side of a fuse terminal.

  1. Contact Surface Preparation (Critical – aR high-speed fuses are sensitive to contact resistance)
  2. Clean copper busbar and fuse terminal contact faces: remove oxidation with scouring pad / fine abrasive paper until bright, then wipe with isopropyl alcohol.
  3. A thin layer of conductive grease (joint compound) 허용된다. Do not apply thick layers, to avoid creepage risk from excess grease squeezing out.
  4. Contact surfaces must be fully mated, free of burrs, gaps and trapped debris.
  5. 설치 후, contact resistance can be checked with a micro-ohmmeter; target per terminal: <50mΩ.
  6. Tightening Procedure
  7. Hand-thread first to align the fuse, keep both terminals parallel and centred.
  8. Tighten with a torque wrench in one smooth movement; avoid repeated back-and-forth adjustment.
  9. Mark the bolt/nut with paint after torque is achieved for tamper/loosening check.
  10. Thermal recheck: after initial energising and 2 hours of load operation, power off and recheck torque. Annual inspection is recommended for long-term service.
  11. 부속품 (TI700 / MAI / MBI)

Microswitches and indicator flags are clip-on accessories. They do not share the main circuit M8 bolts. Do not squeeze or pull the fuse body during fitting; do not alter the compression of the main electrical joint.

  1. 금지된 행위

Do not use A2-70 stainless steel bolts and over-torque (stainless steel has lower yield strength and is prone to thread stripping).

Do not use impact wrenches for final tightening.

Do not force uneven or mismatched busbar thicknesses together.

Do not apply mechanical load or pry on the fuse body.

  1. Common for All FEE Series

100FEE /125FEE /160FEE /200FEE /250FEE /315FEE all use M8 terminals with the same 10 N·m torque specification.

이전:

다음:

답장을 남겨주세요

메시지를 남겨주세요