OMRON E8EB-10C 범용 압력 센서 - 접촉기,회로 차단기,감지기,인코더,PLC,변환기

위챗: +86-13184948252 왓츠앱: 0086-13811255435 이메일: kent@bestcontactor.com

에 대한 연락하다 |

OMRON E8EB-10C 범용 압력 센서 - 접촉기,회로 차단기,감지기,인코더,PLC,변환기

PLC/

OMRON E8EB-10C 범용 압력 센서

제품 유형: Integrated Pressure Sensor (압력 스위치) | 상태: Discontinued by Manufacturer Omron E8EB series integrated pressure sensor with analog + 스위칭 출력, positive pressure type, NPN 출력. ✅ Core Specifications Pressure Range: 0~1 MPa (0~10 kgf/cm², 0~142 psi) 전원공급장치: DC24V Switch Output: NPN 오픈 컬렉터; 맥스. 부하 전류 80 엄마, 맥스. voltage DC30V ...

  • 제품 세부정보

제품 유형: 통합 압력 센서 (압력 스위치) | 상태: 제조업체에 의해 단종됨

옴론 E8EB series integrated pressure sensor with analog + 스위칭 출력, positive pressure type, NPN 출력.

✅ 핵심사양

압력 범위: 0~1 MPa (0~10 kgf/cm², 0~142 psi)

전원공급장치: DC24V

스위치 출력: NPN 오픈 컬렉터; 맥스. 부하 전류 80 엄마, 맥스. voltage DC30V

Linear Analog Output: 1~5 V, Output impedance 20Ω, 최소. load resistance 10 kΩ

응답 시간: ≤5 ms

현재 소비: 20 엄마

압력 포트: RC(PT)1/4

보호 등급: IP54

작동 온도: -10℃~+55℃ (착빙 없음); 저장: -25℃~70℃

지시자: 빨간색 LED (lights up when output is ON)

케이블: 표준 2m 리드선

메디아: Dry air, 비부식성 가스 (Not suitable for corrosive liquid)

📌 Model Code Explanation (E8EB Series)

E8EB = Series Code

10 = Range 0~1MPa

C = NPN output; Suffix B = PNP (Model E8EB-10B)

01 = 0~0.1MPa; N0 = Vacuum type

🔁 Official Replacement Model: E8F2-B10C

목E8EB-10C (구형 모델)E8F2-B10C (대사)
압력 범위0~1MPa0~1MPa
산출NPN 오픈 컬렉터 + 1~5V linear analogNPN, dual independent switch outputs + 1~5V linear analog
현재 소비20엄마70엄마
부하 전류80엄마30엄마
조정Potentiometer adjustment, 디지털 디스플레이 없음디지털 디스플레이 + 막대 그래프, one-touch teaching setup
장착 치수Different footprint and mounting holesCannot be plug-and-play; bracket and piping need modification

⚠️ 중요 공지: Direct plug-in replacement is NOT feasible. 부하 용량, current draw and mounting dimensions differ; PLC wiring logic must be verified.

🧾 Pin Assignment (4-Core Cable)

갈색: DC24V+

파란색: 0다섯 (접지)

하얀색: ON/OFF Switch Output (NPN)

검은색: 1~5V Linear Analog Output

🛠️ Troubleshooting Checklist

  1. 출력 없음: Check 24V supply and blue wire ground; confirm pressure exceeds set threshold
  2. Abnormal analog signal: Load resistance ≥10kΩ; low-resistance loads are prohibited
  3. LED가 켜지지 않음: Pressure not reaching actuation point, or incorrect hysteresis setting
  4. 신호 드리프트: Water/oil contamination in air source, out-of-range temperature, or pressure surge exceeding full scale

📎 Supplementary Information

사용된 / second-hand units are still available on the aftermarket; 새로운 원본 재고 없음

HS 코드 참조: 90262090 (Gas pressure measuring sensor)

대체 모델: E8F2 series, E8CC series digital pressure sensors

E8EB-10C → E8F2-B10C Retrofit Wiring List (4-core old → 5-core new)

E8EB: 4-핵심; E8F2-B10C: 5-핵심 (dual switch outputs + 1~5V analog), NPN, 0~1MPa, DC24V

Goal: Retain the original circuit: 1 switch signal + 1~5V analog; leave the second output unused and insulated.

  1. Wire Color Matching Table
E8EB-10C (오래된, 4-핵심)기능E8F2-B10C (새로운, 5-핵심)기능Connection Plan
갈색DC24V+갈색DC24V+✅ Direct connection
파란색0V 접지파란색0V 접지✅ Direct connection
하얀색Switch Output OUT1 (NPN)하얀색 (아웃1)스위치 출력 1 (NPN)✅ Connect to original PLC input point (keep original pressure signal logic)
검은색1~5V Analog Signal회색1~5V Analog Output✅ Original black wire → new grey wire
—해당 없음하얀색 (아웃2)Independent Switch Output 2 (NPN)⚠️ Leave unused, wrap with insulation; short-circuit strictly forbidden

중요한 알림: The analog output on E8F2 is the grey wire NOT the white wire, this is the most common wiring mistake. If analog signal is not required, insulate the grey wire separately.

  1. 배선 절차
  2. Cut off all power; confirm PLC and sensor power circuits are fully de-energized
  3. Disconnect old sensor terminals and record Brown/Blue/White/Black channel mapping
  4. 전원 회로: Brown to Brown, Blue to Blue (DC24V 공급)
  5. Switch signal: Original white wire → E8F2 OUT1 white wire (match original PLC logic)
  6. 아날로그 신호: Original black (1~5V) → E8F2 grey wire
  7. E8F2 OUT2 white wire: Seal with heat-shrink tube/insulation tape, keep isolated
  8. Inspect wiring for short circuits and exposed copper before powering on.
  9. Parameter Differences & PLC Program Verification Checklist (필수적인)
목E8EB-10CE8F2-B10CRetrofit Risk Point
Current Draw20엄마70엄마Recheck 24V power supply capacity; insufficient margin will cause voltage drop
Switch Load Capacity80엄마30엄마PLC digital input is fine; if the original circuit drives a relay directly, the relay cannot be reused; 부하 전류를 줄인다
Thread PortRC(PT)1/4아르 자형(PT)1/8Must install reducing adapter; cannot thread directly
설치Original bracket28mm 패널 / E89-F3 bracketHole positions do not match; new holes or adapter plate required
설정방법Potentiometer adjustment메뉴 / teaching setupPressure setpoints and hysteresis must be reconfigured; old potentiometer values are invalid
출력 채널Single switchTwo independent switchesProgram only uses OUT1; disable OUT2
  1. Power-On Commissioning Sequence
  2. No-load power-on first; confirm E8F2 digital display lights up normally
  3. 메뉴 진입: Set actuation mode, pressure setpoint and hysteresis to match the original E8EB values
  4. Pressurize and test: Verify OUT1 triggers PLC input correctly
  5. Analog test: 0MPa ≈1V, 1MPa≈5V; confirm linear reading on PLC analog channel
  6. Stabilize signal: Enable anti-chatter filter to prevent false triggering caused by air pressure fluctuation.
  7. 빠른 문제 해결

No analog reading: Grey wire disconnected or misconnected to OUT2 white wire

Cannot drive load: Load current exceeds 30mA rating

No switching action: Parameters not reconfigured; factory default values differ from old sensor

공기 누출: Thread mismatch; missing reducing adapter

Full Commissioning Procedure: E8EB-10C Upgrade to E8F2-B10C (Match Original System Logic)

목적: OUT1 replaces the old E8EB switch point; grey wire 1~5V analog keeps the original PLC analog channel; OUT2 remains unused.

버튼: 세트 (Confirm/Enter), Up ▲, Down ▼; Press and hold SET for 2s to enter main menu; short press SET for pressure setting.

단계 1: 사전 전원 확인 (Prevent PLC Input Burnout)

  1. 배선 확인: 갈색=24V+, 파란색=0V, White=OUT1, Grey=Analog, OUT2 white wire fully insulated
  2. Load check: E8F2 NPN output max. 30엄마. Do not drive relays directly. Add an intermediate relay if the old circuit had a relay load
  3. 관: Install PT1/8 to PT1/4 reducing adapter with thread sealant; test for air leakage before commissioning
  4. Air source: Use dry compressed air free of excessive water and oil; working pressure cannot exceed 1MPa full scale
  5. PLC 측: Analog input impedance ≥10kΩ; low-resistance loads are prohibited.

단계 2: No-Load Power On & Zero Reset (Zero Pressure Condition)

  1. Power the sensor alone, without air pressure applied, wait for display stabilization
  2. Zero point reset (zero pressure calibration): Press ▲+▼ simultaneously to reset zero reading

메모: Zero reset must be done at zero pressure; calibration under pressure will lead to permanent drift.

단계 3: Basic Parameter Setup (Hold SET 2s to enter main menu)

  1. 단위 (unt): Select MPa (consistent with old sensor; kPa is also acceptable)
  2. 작동 모드 (m-a): Select HYS (Hysteresis Mode, same as E8EB); avoid Window Mode
  3. 출력 논리 (ope): NPN, 평상시 열림 (아니요); output ON when pressure exceeds set value
  4. Anti-chatter Filter: Set to STND (기준); select longer filtering if air pulsation is severe to avoid signal chattering
  5. 구하다: Hold SET 2s to return to measurement screen.

Only configure OUT1; leave OUT2 parameters unchanged as it remains unused.

단계 4: Pressure Setpoint Configuration (2 옵션: Manual Input / Teaching Mode; Teaching is Recommended)

옵션 A: 2-Point Teaching (Best for replicating old E8EB trigger points)

  1. Short press SET to enter pressure setting → select OUT1 → select 2-point teaching
  2. Slowly raise pressure to ON actuation pressure, stabilize and press SET to save the ON point
  3. Slowly reduce pressure to OFF release pressure, stabilize and press SET to save hysteresis OFF point
  4. Hold SET to save and exit.

예: Original E8EB turns ON at 0.5MPa and OFF at 0.4MPa; teach these two pressure values directly on site.

옵션 B: Manual Value Entry (If original setpoints are known)

  1. Short press SET → enter OUT1 ON value → adjust value with ▲▼
  2. Press SET to switch to OUT1 OFF value → set hysteresis (끄다 < 에)
  3. Press SET again to jump to OUT2; skip without modification
  4. Hold SET to save and exit.

Recommended hysteresis: Keep consistent with original setting to avoid frequent cycling; factory default hysteresis = 3%FS (30kPa for 0~1MPa range).

단계 5: Switch Output Test (아웃1, PLC Digital Input)

  1. Gradually increase pressure; check E8F2 OUT1 indicator + PLC 입력: ON when pressure ≥ setpoint
  2. Gradually reduce pressure; input turns OFF when pressure drops below OFF threshold
  3. Repeat 3 times to confirm:

No flickering or intermittent signal

Trigger action fully consistent with the old sensor

No premature or delayed switching

문제 해결: Frequent chattering → increase filter time and hysteresis; no action → reverse NO/NC output logic.

단계 6: 1~5V Analog Channel Calibration (Grey Wire, 중요한 단계)

범위: 0~1MPa = 1V ~ 5V

0MPa: Theoretical output ≈1.0V

0.5MPa: Theoretical output ≈3.0V

1.0MPa: Theoretical output ≈5.0V

시운전 단계:

  1. Zero pressure: Confirm PLC analog reading ≈1V
  2. Pressurize to 0.5MPa and cross-check reading
  3. Full scale 1MPa: Verify output ≈5.0V

⚠️ 중요 참고 사항: E8F2 analog output is pre-calibrated for linearity. No re-calibration on PLC side is required. If deviation occurs, redo zero reset first and check load resistance.

단계 7: Full System On-Line Test (Automatic Machine Cycle)

  1. Switch equipment to automatic mode; verify pressure interlock and alarm logic work correctly
  2. Run continuously for 5~10 minutes; confirm output stays stable under pressure fluctuation
  3. Record actuation pressure, hysteresis and filter parameters in engineering change records
  4. Add pressure buffer/throttle on the air inlet if pressure surge occurs to prevent overpressure damage.

단계 8: 오류 문제 해결 표

징후근본 원인치료
OUT1 never switches ONON setpoint too high; NO/NC logic reversedRecheck set value; modify ope output mode
Switch signal flickers continuouslyAir source pulsation; filter time too shortExtend response filter; increase hysteresis value
Analog signal stuck fixed at 1VGrey wire broken/disconnected; load resistance too lowInspect grey wire; ensure PLC input resistance ≥10kΩ
Zero reading drifts constantlyZero reset performed under pressure; air contains water/oilRe-zero at zero pressure; install air filter for moisture removal
Output stays permanently ON after power-upOFF value set higher than ON value (parameter reversed)Ensure OFF pressure < ON pressure
PLC input channel burned outLoad current exceeds 30mA ratingRemove direct relay drive; 중간 릴레이 추가

Full Model List of OMRON General-Purpose Gas Pressure Sensors (영적인 / 압축기 / 진공, Dry Air Only)

메모: All models are Gauge Pressure. 산출: NPN/PNP switch + 1~5V analog. Split into Discontinued Legacy Models + Official Replacement Models, suitable for spare part replacement, BOM & foreign trade.

접미사 정의: C=NPN; B=PNP; A01=0~100kPa; B10=0~1MPa; AN0=Vacuum 0~-101kPa.

  1. E8EB Series (디스플레이 없음, 전위차계 조정, 중단됨)

4-core lead wire, RC1/4 thread, single switch + 1~5V analog; 20mA current draw, 최대. load 80mA.

모델압력 범위산출
E8EB-01기음0~100kPa (0.1MPa)NPN
E8EB-01비0~100kPa (0.1MPa)PNP
E8EB-10C0~1MPaNPN (Main Model in This Retrofit)
E8EB-10B0~1MPaPNP
E8EB-N0C2B0~-100kPa VacuumNPN
E8EB-N0B2B0~-100kPa VacuumPNP
  1. E8F2 Series (디지털 디스플레이, official replacement for E8EB/E8CC, 중단됨)

5-코어 케이블, PT1/8 thread, dual independent switch outputs + 1~5V analog; 70mA 전력 소비; single channel max. load 30mA; one-touch teaching programming.

모델압력 범위산출
E8F2-A01C0~100kPaNPN (E8EB-01C Replacement)
E8F2-A01B0~100kPaPNP
E8F2-B10C0~1MPaNPN (Direct replacement for E8EB-10C)
E8F2-B10B0~1MPaPNP
E8F2-AN0C0~-101kPa VacuumNPN
E8F2-AN0B0~-101kPa VacuumPNP
  1. E8CC Series (Slim digital type, predecessor of E8EB, 중단됨)

With digital display, single switch + 1~5V analog; DIN 레일 장착; replaced by E8F2.

모델압력 범위산출
E8CC-A01C0~100kPaNPN
E8CC-B10C0~1MPaNPN
E8CC-AN0C0~-101kPa VacuumNPN
  1. E8MS / E8M Split Type (Sensor Head + 제어 장치, 중단됨)

Pure 1~5V analog signal without built-in switch; requires E8M controller for multi-channel pressure acquisition.

모델압력 범위유형
E8MS-010~100kPaPositive Pressure Probe
E8MS-100~1MPaPositive Pressure Probe
E8MS-N00~-101kPa VacuumVacuum Probe
E8MS-N1-101~101kPa Compound PressureCompound Pressure Transducer
E8M-100~1MPaE8M Independent Probe
E8M-N00~-101kPa VacuumVacuum Probe
E8M-A10~1000PaMicro Differential Pressure
  1. E8AA Series (Stainless Steel Diaphragm Special Model, 중단됨)

Limited use for liquid / slightly corrosive gas applications.

모델압력 범위
E8AA-M050~500kPa
E8AA-M100~1MPa
  1. E8Y / E8Y-L Micro-Pressure Sensors (Differential Pressure for Duct & 팬, Not General Pneumatic Type)

Pa-level low pressure (200Pa ~5kPa); some models with 4-20mA output; used for air duct and filter differential pressure monitoring only.

✅ Cross Reference Table (Spare Part Replacement Priority)

구형 모델권장 교체주요 차이점
E8EB-01기음E8F2-A01CPT1/8 thread, 듀얼 출력, load current reduced to 30mA
E8EB-10CE8F2-B10CFull retrofit plan covered above
E8EB-N0C2BE8F2-AN0CVacuum pressure type
E8CC-A01CE8F2-A01CDifferent mounting footprint

📌 General Notes

  1. 메디아: Dry non-corrosive air; Not for liquid or strong corrosive gas
  2. Analog Output Standard: 1~5V (1V at zero pressure, 5V at full scale)
  3. Thread Spec: E8EB = RC1/4; E8F2 = R1/8; reducing adapter is mandatory for retrofit
  4. 전원공급장치: DC24V
  5. All listed models are discontinued; 유일한 잉여 재고 & 중고 유닛 사용 가능. New projects shall select the latest OMRON E8F series.

이전:

답장을 남겨주세요

메시지를 남겨주세요