클래식 레거시 모델, 에 중단됨 1997. 시중에 판매되는 중고 부품 또는 재고 예비 부품만 사용 가능.
시리즈: H3BA 다중 모드 솔리드 스테이트 타이머, 8-핀 원형 소켓 (MY 릴레이 베이스와 호환 가능), 다중 작동 모드, wide time range with analog knob setting
- 모델 코드 설명
H3BA: 시리즈명, 다기능 고체 타이머
8: 8-핀 원형 소켓 버전 (the 11-pin variant of the same series is H3BA without suffix 8)
구별: H3BA-8 ≠ H3BA-N8H (N8H is a later upgraded 8-pin model with partial functional differences)
- 핵심사양
- 작동 모드: 4 multi-function modes (에이: 온 딜레이, 비: 섬광, OFF-initiated, 지하 2층: 섬광, ON-initiated, 제이: One-shot). Selectable via DIP switch on unit; self-reset, 외부 리셋 단자 없음.
- 시간 범위 (multi-range switchable)
0.05~1.2s / 1.2~12s / 0.12~1.2min / 1.2~12min / 0.12~1.2h / 1.2~12h, 6 selectable time units, continuously adjustable via knob.
- 출력 접점: SPDT timed contact, resistive load AC250V 5A
- 정격 공급 전압: AC100/110V, AC200/220V, DC24V (defined by model suffix)
- 정확성: Voltage influence ≤±0.5%FS; temperature influence ≤±2%FS
- 주변 조건: -10℃~+55℃, humidity 35~85% non-condensing
- 설치: 패널 플러시 장착. Matched with 8P round base (P3G-08 등.), surface mounting also available.
- 핀 할당 (8-pin round base, top view)
Standard MY relay compatible 8-pin base
핀 2, 7: Power supply terminals
핀 1, 3, 4: Timed SPDT contact (흔한 / NC / 아니요)
핀 5, 6, 8: Second set of timed SPDT contact (for some versions)
메모: Pin definition of legacy H3BA-8 is identical to newer H3CR-A8, critical for replacement.
- 권장 교체 모델 (오므론 official recommendation)
- 직접 교체: H3CR-A8 (8-pin multi-function, pin-compatible, full coverage of H3BA-8 functions, reuse existing base, most common upgrade solution)
- If instantaneous contact required: H3CR-A8E
- 국내 대안: 8-pin multi-function timers (예를 들어. ST3PA-B). Verify pinout and modes carefully.
- Troubleshooting for second-hand spare parts inspection
- Power indicator off after power-up: Check voltage on pin 2 & 7; inspect base contact and pin oxidation; internal power circuit failure (electrolytic capacitor aging is common failure for legacy units).
- Inaccurate / drifting timing: Degraded internal electrolytic capacitor, the most frequent fault of old H3BA timers.
- No contact switching upon timeout: Damaged internal solid-state trigger circuit or burnt contacts.
- 재설정 실패: 최소 전원 끄기 재설정 시간 ≥0.1s; 전원을 끈 후 전원을 빠르게 순환하면 재설정 실패가 발생할 수 있습니다..
- 간섭으로 인한 잘못된 작동: 별도의 전원 케이블과 타이머 제어선; 서지 흡수 장치를 설치하다.
- 선택 & 교체 노트
- 공급 전압을 엄격하게 일치시키십시오. AC220V 및 DC24V 버전은 호환되지 않습니다..
- 작동 모드 요구 사항 확인: H3BA-8은 플래싱 및 원샷을 지원합니다.. 플래싱/원샷이 필요하지 않은 경우 일반 온 딜레이에 대해서만 단순화된 모델.
- 접점등급: 저항 부하의 경우 최대 5A. 접촉기 또는 솔레노이드 밸브와 같은 유도 부하용 중간 릴레이 추가.
- 중고 조달의 위험: 수십년 동안 단종됨, 커패시터 노화는 내재된 위험입니다.. 승인 전에 전원 켜기 번인 테스트 수행.
- HS 코드 참조
85364900 (타임 릴레이, 전자기 / 무접점 지연 릴레이)
H3BA-8 교체 모델 목록 (추천 우선순위별로 정렬)
기존 H3BA-8: 8-핀 원형 플러그, 4 모드 (A 온 딜레이 / B OFF 스타트 플래시 / B2 ON 스타트 플래시 / J one-shot), DPDT timed contacts, reusable base P3G-08/PF085A
✅ OMRON Original Preferred Replacements (direct plug into existing base, 우선 사항)
- H3CR-A8【Official first choice, highly recommended】
Pinout fully compatible with H3BA-8, legacy P3G-08 base can be reused without rewiring
기능: 전체 범위 4 basic modes (A/B/B2/J), time range 0.05s~300h, analog knob setting, DPDT timed contacts, AC250V 5A
차이점: Body approx.12mm shorter than H3BA-8. Panel mounting clip needs replacement with Y92H-8 (PF085A base) / Y92H-7 (PL08 base). Electrical wiring unaffected.
애플리케이션: Most equipment retrofits, original logic unchanged.
- H3CR-A8E (version with instantaneous contacts)
Same pin compatibility with original base; adds one set of instantaneous contacts, matching capability of legacy H3BA-8H
Selection scenario: Choose A8E if circuit requires combined instantaneous + delayed output; not required for simple delay / flashing logic.
콘택트 렌즈: Timed DPDT + instantaneous SPDT
- H3BA-N8H (H3BA series upgraded successor)
Same H3BA second generation, 8-pin round base compatible; more modes (including mode A/H), time range 1.2s~300h
특징: Switchable between【dual timed DPDT】or【timed SPDT + instantaneous SPDT】
주의: Not fully equivalent to legacy H3BA-8. DIP switch logic differs. Requires mode re-calibration after replacement. Better for new projects. H3CR-A8 preferred for direct retrofit of old machines.
⚠️ OMRON Alternatives (단순화된 기능, not recommended for seamless direct swap)
H3Y-2-C: 8-핀, only simple on-delay, no flashing or one-shot. Only suitable for mode A (지연 시) 애플리케이션, cannot run cyclic flashing. Function incomplete.
H3CR-A8S: 트랜지스터 출력 유형, no relay contacts. Cannot directly replace contact circuits. Only for low-level PLC input signals, not for driving contactors or solenoid valves.
🇨🇳 Domestic Alternatives (비용 절감, 기본 호환, verify pinout)
All 8-pin round socket (P3G-08), pin wiring same as OMRON, 4-mode multi-function timer
- ST3PA-B (most common domestic model, 4 모드, 0.05s~300h, 5연락처)
- JSZ3A-B: Domestic 8-pin multi-function timer, specs benchmark H3CR-A8
위험 참고 사항: Domestic units have larger temperature drift and inferior long-term stability vs OMRON. Use caution for critical equipment.
선택 비교표
| 모델 | 상표 | Base Reuse | 모드 | 콘택트 렌즈 | 응용 시나리오 |
| H3CR-A8 | 오므론 | ✅ Direct plug-in | A/B/B2/J 4 모드 | DPDT timed | Retrofit of legacy equipment (첫 번째 선택) |
| H3CR-A8E | 오므론 | ✅ Direct plug-in | A/B/B2/J 4 모드 | Timed DPDT+Instantaneous SPDT | Circuits requiring instantaneous contacts |
| H3BA-N8H | 오므론 | ✅ | Multiple modes including H mode | Switchable timed/instantaneous | 새로운 프로젝트, mode reconfiguration acceptable |
| ST3PA-B | 국내의 | ✅ | 4 모드 | DPDT timed | Non-critical circuits, cost-down retrofit |
| H3Y-2-C | 오므론 | ✅ | Only on-delay | DPDT timed | No flashing / one-shot, limited function |
키 교체 참고사항
- 전압이 일치해야 합니다.: AC220V / AC110V / DC24V are not interchangeable, most common mistake.
- 딥스위치 설정: H3CR-A8 DIP logic matches legacy H3BA-8. Always re-verify mode after replacement.
- 접점등급: Max 5A resistive load. Add intermediate relay for inductive loads like contactors and solenoid valves.
- 장착 클립: H3CR-A8 더 짧은 몸체. 원래 패널 리테이너 클립은 재사용할 수 없습니다.; Y92H 시리즈 클립은 별도로 판매됩니다., 전기 배선에 영향을 미치지 않습니다.
OMRON H3BA 전체 시리즈 모델 목록 (단종된 기존 1세대 + H3BA-N 업그레이드 세대)
주목: 1세대 H3BA (H3BA / H3BA-8 / H3BA-8H) 에 중단됨 1997. H3BA-N / H3BA-N8H는 동일한 시리즈의 이후 업그레이드 버전입니다., 일부 재고가 아직 남아 있습니다.. H3BA-X 단순화된 단일 지연 변형도 존재합니다..
- 1세대 H3BA (유산, 단종; 귀하의 H3BA-8은 이 그룹에 속합니다)
| 모델 | 다리 | 출력 기능 | 핵심 기능 |
| H3BA | 11-핀 라운드 | DPDT timed contacts | 4 다중 모드: A 온 딜레이 / B OFF 시작 플래시 / B2 ON 개시 플래시 / J 원샷 |
| H3BA-8 | 8-핀 라운드 | DPDT timed contacts | 4 다중 모드 (당신의 모델) |
| H3BA-8H | 8-핀 라운드 | 시간 제한 + 즉각적인 접촉 | 4 한 세트의 순간 출력을 갖춘 다중 모드 |
| H3BA-FA | 단자대 종류 (소켓 없음) | DPDT timed | Only on-delay, 깜박임 없음/원샷 |
| H3BA-8S | 8-핀 라운드 | 트랜지스터 출력 | 4 모드, 트랜지스터 출력, no relay contacts |
전압 접미사 분석: AC100/110V, AC200/220V, DC24V. 예: H3BA-8 AC220V, H3BA-8 DC24V.
- 업그레이드된 H3BA-N 시리즈 (H3BA 2세대, 같은 가족)
| 모델 | 다리 | 출력 기능 | 핵심 기능 |
| H3BA-N | 11-핀 | DPDT timed | 6 작동 모드, 다기능 타이머 |
| H3BA-N8H | 8-핀 | 전환 가능: 듀얼타임 / 시간 제한 + 동시에 일어나는 | 6 모드, 8-핀 라운드 베이스 P3G-08 레거시 H3BA-8 베이스와 호환 가능, supports instantaneous contact switching |
| H3BA-X8HA / X8HB / X8HC | 8-핀 | 시간 제한 + instantaneous SPDT | On-delay only, no flashing or one-shot. Different max time ranges: HA=12h / HB=30h / HC=60h |
Voltage suffix also AC110V / AC220V / DC24V.
- Same Platform Derivative Series (H3B family, frequently compared during selection)
Same base footprint as H3BA-N, different functional positioning, not part of H3BA series, often quoted together for procurement
- H3BF-N / H3BF-N8: 듀얼 타이머 (two independent timing stages)
- H3BG-N / H3BG-N8 / H3BG-N8H: Star-delta starter dedicated timer
- H3BH-N / H3BH-N8: Off-delay timer
- H3BA Series Model Coding Rules (Quick model decoding)
H3BA: 시리즈 코드, multi-function analog solid-state timer
Numeric suffix: 8 = 8-pin round socket; no number = 11-pin round socket
접미사 H: Version with instantaneous contacts
Suffix S: 트랜지스터 출력 (no relay contacts)
Suffix N: 2세대 업그레이드 버전 (H3BA-N)
Suffix X: Simplified variant, on-delay only, no flashing or one-shot
HA/HB/HC: Time range differentiation for H3BA-X internal settings
- H3BA Series Official Replacement Summary Table
| Original H3BA Model | OMRON 공식 권장 교체품 |
| H3BA (11-레거시 핀) | H3CR-A (11-핀) |
| H3BA-8 (8-레거시 핀, 당신의 모델) | H3CR-A8 (8-핀, 첫 번째 선택) |
| H3BA-8H (즉각적인 접촉으로) | H3CR-A8E |
| H3BA-N 11핀 | H3CR-A |
| H3BA-N8H | H3CR-A8E |
- 선정 비고
- 레거시 H3BA / H3BA-8 완전 단종, 오직 잉여 / 중고품. 내부 전해 커패시터 노화는 고유한 고장 모드입니다..
- H3BA-N8H는 H3BA-8과 동일한 8핀 베이스를 사용합니다., 하지만 DIP 스위치 모드 로직은 레거시 H3BA-8과 다릅니다.. 직접 교체하는 경우 모드를 다시 보정하십시오..
- H3BA-X 시리즈는 H3BA-8을 대체할 수 없습니다., B/B2/J 깜박임 및 원샷 모드 누락; 단순 온 딜레이만 가능.
접촉기,회로 차단기,감지기,인코더,PLC,변환기



















NH42-63-318x560.png)



