OMRON CP1W-8ER Pure Output Expansion Module - Contactor,întrerupător de circuit,senzor,Codificator,PLC,Convertor

Wechat: +86-13184948252 Whatsapp: 0086-13811255435 E-mail: kent@bestcontactor.com

Despre Contact |

OMRON CP1W-8ER Pure Output Expansion Module - Contactor,întrerupător de circuit,senzor,Codificator,PLC,Convertor

PLC/

OMRON CP1W-8ER Pure Output Expansion Module

CP1W: Expansion unit for CP1 series 8: 8 points E: Expansion R: Relay normally open (NU) output Type: Pure output expansion module, no input points Core Specifications Number of output points: 8-point relay NO output Rated current per channel: 2 O (sarcină rezistivă) Output voltage range: AC/DC 4.5~30 V (passive relay contact) On/off delay: aproximativ. ...

  • Detalii despre produs

CP1W: Expansion unit for CP1 series

8: 8 puncte

E: Expansiune

R: Relay normally open (NU) ieșire

Tip: Pure output expansion module, no input points

Specificații de bază

Number of output points: 8-point relay NO output

Rated current per channel: 2 O (sarcină rezistivă)

Output voltage range: AC/DC 4.5~30 V (passive relay contact)

On/off delay: aproximativ. 15 Domnișoară

Consumul de energie: 5 În DC 0.21 O; 24 În DC 0.13 O

Dimensiuni: W66 × H90 × D50 mm

Greutate: aproximativ. 250 g

Certificari: CE, UL, CSA

Lifecycle status: Activ, not discontinued

Compatibil CPU Units

CP1E / CP1H / CP1L (CP1 series PLC); also compatible with legacy CPM1A/CPM2A

Nota: 20-point CP1E CPU does not support expansion. Only 30/40/60-point CPUs can connect CP1W expansion units.

Cross-model Comparison (for selection)

CP1W-8ER: 8-ieșire releu punctual (passive, AC/DC universal)

CP1W-8ET: 8-point NPN transistor output (Doar DC24V)

CP1W-8ED: 8-punctul DC24V input module

CP1W-16ER: 16-ieșire releu punctual

Ghid de cablare

  1. Two independent common terminals: COM0 (00~03), COM1 (04~07)
  2. Relay is dry contact: connect AC L / DC+ to COM as required, then wire the load to the contact terminal
  3. Nu conduceți direct motoare de mare putere; add intermediate contactors
  4. Pentru sarcini inductive (electrovalve, bobine), install freewheeling diodes (DC) or RC snubbers (AC) to extend relay life.

Depanare

Nicio acțiune de ieșire:

1) Check if the expansion cable is firmly plugged in and the CPU recognizes the expansion unit

2) Verify the I/O address assignment (expansion I/O follows the previous unit’s address sequentially)

3) Measure COM power supply and check for open circuits in the load loop

Permanent ON for one channel: relay contact welding; replace the point or the whole module

No output on all channels: expansion function disabled, too many expansion units, or damaged cable.

Opțiuni de înlocuire

  1. Înlocuire directă: CP1W-8ER (preferat, no program modification needed)
  2. Transistor alternative: CP1W-8ET (for high-frequency switching and DC loads; cannot handle AC)
  3. Alternativă internă: CP1-bus compatible 8-point relay expansion module (verify bus protocol and address mapping)

Service Life of CP1W-8ER (Limited by relay contacts)

Official rated life per relay channel

  1. Durata de viata mecanica (funcționare fără sarcină): ≥20 million operations
  2. Durata de viata electrica (2 A resistive load): ≥100.000 de operații

Key point: Electrical life is the bottleneck, not the PCB. Sarcini inductive (electrovalve, bobine de contactor) drastically shorten service life down to 20,000~50,000 cycles. Snubber circuits will improve this.

Time Estimation (for project evaluation)

1 operation per minute: 100,000 cycles ≈ 19 ani

1 operation per 10 secunde: 100,000 cycles ≈ 2.8 ani

1 operation per second: 100,000 cycles ≈ 27 ore

For equipment with continuous ON state and rare switching: contact wear is minimal. In clean, temperature-controlled cabinets, the PCB, cable and terminals can run stably for 8~15 years. Service life is halved in high-temperature, medii umede și prăfuite.

Two Types of Service Life

Contact life: limited by switching cycles; failure symptoms: contact welding or poor contact

Module body life: PCB, cable and drive circuit; aging depends on environmental conditions, no fixed cycle rating.

Life Extension Tips

  1. Add freewheeling diodes (DC) or RC snubbers (AC) for inductive loads such as solenoid valves and contactors.
  2. Keep load current below 1 O; avoid continuous full-load (2 O) operare.
  3. For high-frequency switching (cycles within seconds), use CP1W-8ET transistor output instead of ER relay modules.
  4. Regularly inspect expansion cables and terminals for oxidation and loose connections.

Full List of OMRON CP1W Expansion Units (CP1E / CP1H / CP1L Compatible)

Nota: CP1W units are bus-connected expansion modules (daisy-chained with flat cable). CIF, ADB and DAB boards are CPU side option boards (not bus expansion units). 20-point CP1E cannot use expansion units; only 30/40/60-point CP1E, CP1H and CP1L-M support CP1W expansion.

  1. Digital Input Only Units
ModelDescriere
CP1W-8ED8-point DC24V input (NPN/PNP universal)
  1. Digital Output Only Units (CP1W-8ER listed here)
ModelDescriere
CP1W-8ER8-point relay NO output, 2 O
CP1W-8ET8-point NPN (sinking) ieșire tranzistor, 0.3 O
CP1W-8ET18-point PNP (sourcing) ieșire tranzistor, 0.3 O
CP1W-16ER16-point relay NO output, 2 O
CP1W-16ET16-point NPN transistor output, 0.3 O
CP1W-16ET116-point PNP transistor output, 0.3 O
CP1W-32ER32-point relay NO output, 2 O
CP1W-32ET32-point NPN transistor output, 0.3 O
CP1W-32ET132-point PNP transistor output, 0.3 O
  1. Mixed I/O Units (Intrare + Output integrated)
ModelDescriere
CP1W-20EDR112 DC inputs + 8 ieșiri releu
CP1W-20EDT12 DC inputs + 8 NPN transistor outputs
CP1W-20EDT112 DC inputs + 8 PNP transistor outputs
CP1W-40EDR24 DC inputs + 16 ieșiri releu
CP1W-40EDT24 DC inputs + 16 NPN transistor outputs
CP1W-40EDT124 DC inputs + 16 PNP transistor outputs
  1. Analog I/O Units (Voltaj / Current signal)
ModelDescriere
CP1W-AD0414 AI, rezoluţie 1/6000; voltage/current selectable
CP1W-AD0424 AI, rezoluție înaltă 1/12000
CP1W-DA0212 LA, rezoluţie 1/6000
CP1W-DA0414 LA, rezoluţie 1/6000
CP1W-DA0424 LA, rezoluție înaltă 1/12000
CP1W-MAD112 AI + 1 LA, rezoluţie 1/6000
CP1W-MAD424 AI + 2 LA, rezoluție înaltă 1/12000 (cele mai populare)
  1. Temperature Input Units (Termocuplu / Pt RTD)
ModelDescriere
CP1W-TS0012-channel thermocouple (K/J type)
CP1W-TS0022-channel Pt100/Pt1000 RTD
CP1W-TS0032-channel multi-function: thermocouple / RTD / intrare analogică
CP1W-TS00412-channel thermocouple (for oven & injection molding multi-point temperature monitoring)
  1. Accesorii (Expansion Cable)
ModelDescriere
CP1W-CN81180 cm extension cable; short cable (6 cm) included with each module

Suplimentar: CPU Side Option Boards (NOT Bus Expansion Units)

These plug directly into the CPU side slot and cannot be daisy-chained on the I/O bus:

CP1W-CIF01: RS232C

CP1W-CIF11: Non-isolated RS422/485

CP1W-CIF12 / CIF12-V1: Opto-isolated RS422/485

CP1W-CIF41: Ethernet option board

CP1W-DAM01: LCD display panel

CP1W-ADB21 / DAB21V / MAB221: Small analog option boards

Ghid de selecție rapidă

  1. High-frequency switching, electrovalve, servo pulse output → Choose ET / ET1 transistor models, do not use ER relay modules
  2. AC220V loads with infrequent switching → Select ER relay models
  3. Thermocouple temperature measurement: TS001; Pt RTD: TS002; multi-point temperature monitoring: TS004
  4. I/O analogic: MAD42 (4-in 2-out) este de preferat; new projects select high-resolution AD042 / DA042

 

Prev:

Următorul:

Lasă un răspuns

Lăsaţi un mesaj