Schneider XY2CH13250 Latching Emergency-Stop Rope-Pull Switch

Explicația modelului: XY2CH series, booted push-button reset, 1NC+1NO, without indicator lamp; XY2CH13250H29 = cable entry thread changed to M20; standard version is Pg13.5.

Comparison with XY2CH13290: 13250 features only one safety NC contact; 13290 adopts dual-channel safety with two NC contacts — this is the core difference.

Specificații de bază

Terminal Assignment

⚠️ Critical: Only one safety NC contact; no second hardware safety channel.

Stare normală: 21-22 închis, 13-14 deschide. Pulling the rope triggers mechanical latching: 21-22 opens, 13-14 se inchide. Restore by pressing the blue reset push-button.

Wiring Schemes

Schema 1: High-Safety Level (PL e requires safety-relay monitoring)

1. Sârmă 21-22 (NC) to one input channel of safety relay.
2. Sârmă 13-14 (NU) to PLC DI for alarm feedback signal.

Since the hardware provides only one NC channel, Category 4 / PL e can only be achieved when the safety relay implements contact short-circuit monitoring. Without monitoring, max achievable safety level is PL c.

❗Do NOT externally parallel contacts; hardware only supplies one safety contact.

Schema 2: Low-risk general-purpose equipment (PL e not satisfied)

Sârmă 21-22 in series into equipment emergency-stop circuit; 13-14 for alarm feedback.

Suitable for light-duty general-purpose conveyors. Strictly prohibited for high-risk conveyor systems.

Măsuri de precauție pentru cablare

1. Use only one cable entry; fit sealing plugs on the remaining two unused entries, otherwise IP65 protection is lost.
2. Connect metal housing reliably to PE protective earth.
3. Tighten terminals strictly to 0.8-1.2 N·m to avoid loose connections.

Instalare mecanică

Mechanical installation requirements are identical to XY2CH13290. Refer to the full installation manual below:

1. Max rope span 30 m; use φ3-5 mm plastic-coated steel wire rope.
2. End-position tension spring is mandatory. Rope breakage shall also trigger emergency stop.
3. First deflection pulley shall be mounted 100 mm away from switch body. Install rope clamps/support points every 5 m.
4. Mount onto rigid metal brackets only; allow slight rope sag — do not over-tension nor allow excessive slack.

Pre-power-on Commissioning (de-energised, multimeter test)

1. Reset completed: 21-22 închis, 13-14 deschide.
2. Pull rope to trigger latching: 21-22 deschide, 13-14 închis.
3. Press reset push-button to restore contact states.
4. Test actuation at multiple positions all along the rope path to confirm reliable triggering even at far-end positions.

Comparație de modele: XY2CH13250 vs XY2CH13290

Selection Reminder: Prefer 13290 for belt conveyors and heavy-duty lines; 13250 is acceptable for light-duty general-purpose machines.

Equivalent Replacement Models

1. Original Schneider variantă: XY2CH13250H29 (M20 thread version)
2. Alternative interne:

ELCO SR1-SN (1NC+1NO)

Schmersal ZQ700-11

Depanare comună

1. Unintended nuisance tripping: Excessive rope tension, bracket vibration. Reduce tension via turnbuckle; reinforce mounting structure.
2. No actuation from far-end pull: Insufficient rope tension, seized deflection pulleys. Adjust tension; service pulleys.
3. Cannot reset after tripping: Persistent tensile load remains on rope. Release rope residual tension before pressing reset button.

Tip de produs: Latching emergency-stop rope-pull safety switch. Pulling the steel wire rope triggers emergency stop with mechanical latching; manual reset is mandatory. Applied to long-run conveyors, linii de asamblare, mașini de ambalare, belt conveyors and other machinery safety protection.

General Core Specifications

Model Naming & Main XY2CH Variants

XY2CH + numeric suffix. Suffix defines contact configuration, reset type, pilot-lamp option and thread specification.

1. Reset Types

131xx: Flat push-button reset

132xx: Booted dust-protected push-button reset (most common industrial type)

134xx: Key-operated reset

2. Contact Configurations

XY2CH13250: 1NC+1NO, booted push-button reset

XY2CH13270: 2NC, dual safety normally-closed contacts

XY2CH13290: 2NC+1NO (cele mai populare; 2 safety NC + 1 signal NO)

XY2CH13450: 1NC+1NO, key-reset

XY2CH13293: 2NC+1NO, with 24 V pilot lamp

Suffix H29 = cable-entry thread changed to M20; default = Pg13.5.

Principiul de funcționare

1. Pull steel wire rope → internal mechanism latches mechanically; safety NC contacts positive-open.
2. Machine shuts down; no automatic reset.
3. After fault clearance, reset via push-button / cheie; contacts restore for machine restart permission.

⚠️ Notă: Rope-run ends must be fitted with tension springs, rope clamps and deflection pulleys. Avoid over-tightening or excessive slack. Rope-clamp spacing ≤ 5 m recommended.

Aplicații tipice

Transportoare cu bandă, linii de producție, linii de ambalare, sisteme de sortare, long workstations, mining conveying equipment. Operators can trigger emergency stop by pulling the rope anywhere along the protected span.

XY2C Family Series Differentiation

XY2CH: Zamak zinc-alloy body, stainless-steel cover, max 30  m rope length, IP65, high mechanical endurance.

XY2CE: Carcasa din plastic, economy-grade, max 2 × 50  m bidirectional rope pull.

XY2CJ: Higher-grade IP66/IP67 protection for heavy-dust and wash-down environments.

Domestic-brand Reference Replacements

ELCO: SR-series rope-pull E-stop switches

Omron: D4A-N rope-pull switches

Contrinex / Schmersal: ZQ-series rope-pull safety switches

General Fault-Finding

1. Frequent nuisance tripping: Excessive rope tension, seized pulleys, deformed mounting brackets.
2. Resetarea eșuată: Mechanism jammed; residual rope tension not released.
3. Open-circuit safety loop: Terminale libere; verify tightening torque 0.8-1.2 N·m.

Schneider XY2CH13290 (Telemecanique Rope-Pull Emergency-Stop Switch)

Contacte: 2NC+1NO, booted push-button reset, no pilot lamp; max rope length 30  m; IP65; Pg13.5 cable entries. Suffix H29 = M20 thread.

1. Terminal Assignment

Non-actuated state: 21-22 închis, 31-32 închis, 13-14 deschide.

Rope-pull latching: 21-22 şi 31-32 open simultaneously; 13-14 se inchide. Reset only via blue local push-button.

2. Wiring Schemes

Scheme A: Safety-relay connection (achieve PL e / Cat.4 / SIL3 — Recommended)

1. Feed independent dual NC channels 21-22 şi 31-32 separately into dual-channel safety-relay inputs. Never externally short-circuit the two NC contacts — this invalidates safety rating.
2. Sârmă 13-14 NO contact to PLC digital input for rope-pull-triggered alarm.
3. Cuplul de strângere a bornei: 0.8-1.2 N·m. Conductor: 0.34-1 mm² single-wire / max 0.75 mm² for two-wire parallel.
4. Cable glands: 3 × Pg13.5; use one only; seal remaining two with blanking plugs to preserve IP65.

Scheme B: Simplified stand-alone wiring (PL e not satisfied, for basic stop-function only)

Wire both NC contacts in series into emergency-stop circuit; NO for alarm output. Cannot reach Category 4; only for low-hazard machinery.

⚠️ Important: This is a mechanically latched device. It will NOT auto-reset after rope-pull actuation; manual push-button reset is required.

3. Mechanical Installation Key-Points
4. Steel wire rope: φ3-5 mm plastic-coated; max total length 30  m; fit tension springs at both ends.
5. Rope clamps: install every ≤ 5  m; add deflection pulleys to prevent rope-to-housing friction.
6. Rope tension: evitați strângerea excesivă (nuisance tripping) and excessive slack; permit minor sag.
7. Suport de montare: rigid metal construction; no flexible supports. Switch can accept rope entry from left or right side.
8. Temperatura mediului ambiant: −25 ℃ ~ +70 ℃.
9. Dimensiuni generale (mm)

Corp: W 68 × H 95 × D 201 (including reset button and rope-pull lever mechanism)

Orificii de montare: two M8 mounting holes on both sides.

5. Original Schneider Equivalent-variant Selection Table

6. Pin-to-pin Compatible Domestic Replacements
7. Schmersal ZQ 900-22 (2NC+1NO, push-button reset)
8. ELCO SR2-SN (2NC+1NO)
9. Contrinex SN21-RPL-30M

Memento de înlocuire: Verificați configurația contactului, reset type, max rope length and protection rating.

7. Depanare
8. Frequent nuisance tripping: Excessive rope tension, seized pulleys, deformed brackets, heavy machine vibration. Reduce rope tension; inspect deflection pulleys.
9. Cannot reset after tripping: Residual rope tension keeps mechanism locked. Release rope tension before pressing reset button.
10. Intermittent open safety circuit: Under-torqued terminals. Retighten terminals to 0.8-1.2 N·m; re-crimp conductors.
11. Water ingress damage: Unused cable entries not sealed with blanking plugs.

Complete Installation Operating Guide for Schneider XY2CH-Series Rope-Pull Emergency-Stop Switches

Modele aplicabile: XY2CH13290, XY2CH13270, XY2CH13250 etc. Complies with EN/ISO 13850, IEC 60947-5-5, Machinery-Safety Directives.

⚠️ Safety Precondition: Perform all installation, wiring and commissioning with equipment de-energised under Lock-Out-Tag-Out (INIMA). This is a tension-type rope-pull switch; proper pre-tension is required. Rope breakage shall also trigger emergency-stop protection.

1. Pregătirea înainte de instalare

1.1 Instrumente & Accessories List

1.2 Environmental Verification

1. Temperatura de functionare: −25 ℃ ~ +70 ℃; Clasament IP65. Avoid heavily corrosive and high-impact locations.
2. Max effective rope-protected length 30  m. Install an additional rope-pull switch if span exceeds this limit.
3. Operating rope height above ground: 0.6-1.1 m, easily reachable by personnel; no obstacles obstructing the rope path.
4. All mounting brackets must be rigid metal. Thin-sheet / flexible supports are forbidden; vibration will cause false triggering.
5. Mechanical-body Mounting Procedure
6. Secure the switch body

Fasten with M8 bolts through the two side mounting holes onto rigid machine frame; tightening torque 4 N·m. Align switch rope-exit direction with rope routing; do not twist the rope-pull lever mechanism.

Maintain 100 mm distance between switch body and first deflection-support point. Larger distance causes insufficient actuation stroke.

2. Fit deflection pulleys

Fit deflection pulleys wherever the rope changes direction. Total deflection-angle sum ≤ 180°. Sharp bends and hard kinks are prohibited.

Install support / rope-clamp assemblies every 5 m along straight runs to limit rope sag.

Pulleys shall rotate freely without binding. Rope must not rub against machine frames or enclosures.

3. Steel-wire-rope & end-spring assembly (pas critic)

1) Attach one rope end to the XY2CH rope-pull eyelet.

2) Thread rope through all deflection pulleys.

3) Fit end-position tension spring at the far rope end. Anchor the spring’s opposite end to rigid machine frame. Omission of this spring is a major safety hazard — pulling towards the switch will fail to trigger E-stop.

4) Secure rope with at least two rope clamps. Do not clamp over the sheath-stripping transition zone.

5) Adjust total rope tension via turnbuckle: keep rope moderately taut with minor sag. Do not over-tighten; do not allow excessive slack.

Over-tension: vibration-induced nuisance tripping. Under-tension: no reliable actuation from far-end positions.

4. Mechanical acceptance check

Rope free of twist, kinks and abrasion. Avoid large-area sheath stripping to prevent corrosion.

Full-rope-travel movement is smooth without binding.

Verifica: rope breakage will cause spring retraction and trigger emergency-stop.

3. Electrical Wiring Procedure

XY2CH13290 terminals: 21-22 NC1; 31-32 NC2; 13-14 NU. Metal housing includes PE earth terminal. Housing must be reliably connected to PE protective earth.

1. Remove four cover screws and open housing.
2. Cable-entry handling:

Standard units: 3 × Pg13.5 threaded entries; H29 variants: M20.

Use only one entry for control-cable feed-through. Tighten original sealing blanking plugs on the other two unused entries (torque 1 N·m). Failure destroys IP65 protection and causes water ingress.

3. Cablajul terminalului (for PL e / Cat.4 / SIL3 safety-loop):

Feed dual safety NC contacts 21-22 şi 31-32 into separate safety-relay dual-channel inputs. Never externally short-circuit the two NC contacts — safety rating will be lost.

Sârmă 13-14 NO contact to PLC input for rope-pull-trigger-alarm signal.

Secțiunea conductorului: single-wire 0.34-1 mm²; max 0.75 mm² for two-wire parallel. Terminal tightening torque 0.8-1.2 N·m.

4. Connect PE protective-earth wire to housing earth terminal for EMC and shock-hazard protection.
5. Refit cover and evenly tighten four cover screws.

❗Simplified wiring (not for high-hazard machinery): Series-connect both NC contacts into general-purpose emergency-stop circuit. This provides only basic stop-function and does not achieve Category 4 safety rating. For low-risk equipment only.

4. Pre-power-on Static Commissioning (de-energised, multimeter measurements)
5. Normal reset-completed state

Multimeter readings: 21-22 închis, 31-32 închis; 13-14 deschide.

2. Manually pull rope to trigger mechanical latching

Multimeter readings: 21-22 deschide, 31-32 deschide; 13-14 închis.

Latching is maintained; contacts will not auto-recover.

3. Press blue booted reset push-button; contacts return to initial status.
4. Simulate actuation at multiple positions along rope path: near switch, mid-span and far-end. Reliable latching actuation must occur at every position.

Poor far-end actuation: reduce rope tension or check for seized pulleys.

5. Simulate rope breakage: spring retraction must trigger emergency-stop latching.
6. Live-machine Functional Test
7. Energise machine and safety-relay system.
8. Test 1: Pull rope near switch → controlled machine shutdown; safety-relay fault indication. Manual reset at switch body AND safety-relay reset are required before machine restart. No automatic-power-on after supply restoration permitted.
9. Test 2: Pull rope at mid-span and far-end positions. Confirm controlled emergency-stop at all points.
10. Test 3: Verify PLC alarm signal (13-14 NU) correctly reports rope-pull-trigger events.
11. Criterii de acceptare a instalării
12. Mecanic: Rigid mounting brackets, free-running pulleys, intact tension springs, correct rope tension, no mechanical interference or friction.
13. Protecţie: All unused cable entries sealed with blanking plugs; cover screws tightened; PE-earth connection intact.
14. Electric: Dual-channel NC contacts fed independently to safety-relay inputs (no external short-circuit). Multimeter test sequences fully compliant.
15. Funcţional: Reliable latching E-stop from any rope-span position; manual-only reset; rope-break triggers emergency-stop.
16. Installation-related Fault-Finding Table

8. Periodic-maintenance Requirements (to be documented in machine-maintenance manual)
9. Weekly visual inspection: rope abrasion, loose rope clamps, deformed springs, loose mounting brackets.
10. Monthly full-functional test: trigger emergency-stop at multiple rope-span positions.
11. Quarterly inspection: re-verify terminal torque and PE-earth integrity; inspect rope-sheath wear.
12. Immediately replace steel-wire rope if wire-strand breakage or sheath damage is observed.

Supplementary note: XY2CH shall not be treated as a general-purpose limit switch. Permanent rope anchoring without end-position tension spring constitutes a serious safety violation.