Основная информация
Модель: 200FEE
Тип: BS88 Part4 / IEC60269-4 high-speed bolted dual-barrel предохранитель, класс аР (for semiconductor protection only)
Номинальный ток: 200А
Электрические характеристики
IEC Rating: 690В и / 500В Вашингтоне
UL Rating: 700В и / 500В Вашингтоне
Разрывная способность: 200тот (AC rms); 50kA @500V DC
Предварительная дуга I²t: 1900; Общий клиринг I²t: 7100@415В, 11400@660V
Power Dissipation: 52Вт
No built-in fuse indicator; external kits TI700, MAI / MBI microswitch assemblies are available
Монтажные размеры
Монтажный болт: М8
Terminal Centre Spacing: 71мм
Строительство: Offset dual-barrel, bolt-connected blade terminals (blade end × blade end)
Общий размер: 187ширина мм, 100мм в длину, 22mm high, Вес нетто: 89.6г
Разрешения & Стандарты
CE, РоХС, UL признан
Стандарты: BS88 Part4, МЭК 60269-4
Типичные применения
Short-circuit protection for frequency converters, выпрямители, DC busbars, приводы постоянного тока, thyristors and IGBT power semiconductors
Reference Models in the Same Series (FEE Series)
100FEE, 125FEE, 160FEE, 200FEE, 250FEE, 315FEE, и т. д.. Same design logic, only rated current differs
Примечания по замене
This is a BS88-4 aR high-speed semiconductor fuse. For domestic alternatives, проверять: aR classification, I²t value, отключающая способность, M8 mounting and 71mm centre spacing. Ordinary gG/gL distribution fuses cannot be used as substitutes.
The 200FEE (FEE series BS88 Part4 aR high-speed dual-barrel fuse) has no original standard moulded fuse holder.
It is designed as M8 bolt-on blade terminals (blade end). The standard installation method is direct mounting onto busbars. Holders such as RS200H (Red Spot) are not required (RS200H is for BS88-2 gG distribution fuses and is incompatible with FEE high-speed semiconductor fuses).
Дополнительные аксессуары (Not Holders – Indicator / Microswitch Kits)
TI700: Fuse indicator kit (indicator flag + клип)
MAI: Microswitch adapter (fuse blown alarm signal)
MBI: Microswitch adapter (alternative construction)
Two Engineering Solutions
- Standard Solution (Most common for VFD / DC busbars)
Direct busbar mounting with M8 bolts, 71mm terminal centre spacing. TI700 / MAI / MBI may be fitted for blown-fuse signalling as required.
- IP20 Enclosed Holder (Альтернативное решение)
No original Bussmann holder is available. Only third-party bolt-on high-speed fuse holders can be selected. Mandatory selection criteria:
Compatible with M8 terminals, 71mm centre spacing, rated ≥200A, 690В, класс аР, breaking capacity ≥200kA
All FEE series models (100FEE /125FEE /160FEE /200FEE /250FEE /315FEE) adopt the same busbar bolt-on design; no original holders are supplied.
200FEE (FEE Series BS88 Part4) Момент затяжки при установке & Tightening Specification
Примечание: The manufacturer datasheet does not specify torque for this individual model. The values below are industry standard practice for Eaton BS88 fuses and busbar connections, widely used for VFD and DC bus projects.
Размер болта: М8 (coarse pitch 1.25), 8.8 grade galvanized bolts preferred
✅ Recommended Torque: 10 Н·м (±1 N·m)
Acceptable Range: 9 Н·м (мин) ~ 12 Н·м (Макс)
Do not exceed 12 Н·м: risk of deforming fuse copper terminals and uneven contact surfaces. Torque below 9 N·m causes high contact resistance, overheating and nuisance blowing.
- Washer Stack Order (from busbar outwards)
Busbar → Fuse blade terminal → Plain washer → Spring washer → Nut
Запрещенный: Spring washer between fuse terminal and copper busbar; stacking multiple lugs on one side of a fuse terminal.
- Contact Surface Preparation (Critical – aR high-speed fuses are sensitive to contact resistance)
- Clean copper busbar and fuse terminal contact faces: remove oxidation with scouring pad / fine abrasive paper until bright, then wipe with isopropyl alcohol.
- A thin layer of conductive grease (joint compound) разрешено. Do not apply thick layers, to avoid creepage risk from excess grease squeezing out.
- Contact surfaces must be fully mated, free of burrs, gaps and trapped debris.
- После установки, contact resistance can be checked with a micro-ohmmeter; target per terminal: <50мОм.
- Tightening Procedure
- Hand-thread first to align the fuse, keep both terminals parallel and centred.
- Tighten with a torque wrench in one smooth movement; avoid repeated back-and-forth adjustment.
- Mark the bolt/nut with paint after torque is achieved for tamper/loosening check.
- Thermal recheck: after initial energising and 2 hours of load operation, power off and recheck torque. Annual inspection is recommended for long-term service.
- Аксессуары (TI700 / MAI / MBI)
Microswitches and indicator flags are clip-on accessories. They do not share the main circuit M8 bolts. Do not squeeze or pull the fuse body during fitting; do not alter the compression of the main electrical joint.
- Запрещенные действия
Do not use A2-70 stainless steel bolts and over-torque (stainless steel has lower yield strength and is prone to thread stripping).
Do not use impact wrenches for final tightening.
Do not force uneven or mismatched busbar thicknesses together.
Do not apply mechanical load or pry on the fuse body.
- Common for All FEE Series
100FEE /125FEE /160FEE /200FEE /250FEE /315FEE all use M8 terminals with the same 10 N·m torque specification.
Контактор,автоматический выключатель,датчик,Кодер,ПЛК,Конвертер





















NH42-63-318x560.png)



